Table of Contents
Advertisement
Quick Links
®
DYE Precision Inc.
USA 10637 Scripps Summit Ct. San Diego, CA 92131 P 858-536-5183 F 858-536-5191
EUROPE Unit 1, ZK Park, 23 Commerce Way, Croydon, Surrey CRO 4ZS United Kingdom
P +44 (0) 20-8649-6330 F +44 (0) 20-8649-6339
ASIA 3F-2, No. 287, Jung Jeng Rd., Luju Hsiang, Taoyuan 338, Taiwan (R.O.C.)
P +886-3-312-6540 F +886-3-311-8723
www.dyepaintball.com
©2005 DYE Precision, Inc. The stylized "dye" logo, the "Sphere" logo, the "DM6" logo, FUSE bolt and Hyper
2
are either registered trademarks, trademarks, design trademarks, patents or pending patents of DYE Precision, Inc.
Covered by U.S. Patent # 5,613,483. Additional patents pending.
Advertisement
Table of Contents
Related Manuals for dye DM6
Summary of Contents for dye DM6
- Page 1 P +886-3-312-6540 F +886-3-311-8723 www.dyepaintball.com ©2005 DYE Precision, Inc. The stylized “dye” logo, the “Sphere” logo, the “DM6” logo, FUSE bolt and Hyper are either registered trademarks, trademarks, design trademarks, patents or pending patents of DYE Precision, Inc. Covered by U.S. Patent # 5,613,483. Additional patents pending.
-
Page 2: Table Of Contents
BOARD SETTINGS AND FUNCTIONS ................... . . PAGE 04 INCLUDED WITH YOUR DM6 FUSE BOLT . -
Page 3: Quick Reference
W A R N I N G Air Supply - The DM6 should be operated using air/nitrogen gas only. This air needs to be supplied to the Hyper 2 ™ in-line regulator at a regulated pressure of no more than 850 psi. -
Page 4: Board Settings And Functions
Firing the DM6 There are two DIP switches mounted on the board of the DM6 (See figure 2). The first one is used for the ABS As soon as the marker is turned on and the LED’s turn from blue to either red or green, the DM6 is ready setting and the second one is used to access a configuration mode used to change the other four settings. - Page 5 [When Anti Chop Eye (ACE) is deactivated] The ROF setting is used to set the maximum rate of fire of the DM6. The values do not correspond directly to a certain nament use, it is recommended to change the battery for each tournament. When changing your battery, take special Balls Per Second (BPS) value.
-
Page 6: Fuse Bolt
If you do not grease the bolt, you will run the risk of damaging o-rings. This will create excessive friction and drag on the bolt, ultimately resulting in breaking the bolt. When greasing the DM6 Fuse™ bolt, pay special attention to all o-rings that are on the bolt and that ride on a surface of the bolt. The first seven o-rings listed below should be The FUSE™... -
Page 7: On/Off Valve
7 Main seal (mounted in the seal retainer) FIGURE 1 FIGURE 2 The On/Off knob is located under the barrel in the front of the DM6 (see figure 2). Using the on/off is simple. To turn 3 Piston spring 8 Seal retainer o-ring (010 BN70) the gas off, turn the knob so that is is facing sideways. -
Page 8: Hyper
(see figure 3). When the bolt tip O-ring passes these acrylic pieces, it sweeps off any dirt, grease or paint The Hyper 2 ™ has eight components and six o-rings that could be blocking the eyes. Normally it is enough to just fire the DM6 to clean anything blocking the eyes. If this does not 1 Retaining cap... - Page 9 • Using a 3/32" allen key, turn the front frame screw counterclockwise one full turn 14 LPR premature wear on the microswitch, • Finally, turn out the back frame screw and slide the frame back and down until it comes off the DM6 resulting in failure. 15 LPR Cap To connect the frame follow above steps in reverse order.
-
Page 10: Trouble Shooting Guide
If it comes from somewhere around the solenoid, the first thing to do is to turn the costs. Warranty card and proof of purchase must be submitted to Dye Precision for warranty to be in effect. This warranty is not transferable. This warranty does not cover on/off knob to the off position.
Need help?
Do you have a question about the DM6 and is the answer not in the manual?
Questions and answers