SAFETY INFORMATION This service manual is intended for qualified service technicians ; it is not meant for the casual do- it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair complex products such as those covered by this manual. Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty.
Page 3
[Important Check Points for Good Servicing] In this manual, procedures that must be performed during repairs are marked with the below symbol. Please be sure to confirm and follow these procedures. 1. Product safety Please conform to product regulations (such as safety and radiation regulations), and maintain a safe servicing environment by following the safety instructions described in this manual.
2. EXPLODED VIEWS AND PARTS LIST NOTES: Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List. mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation.
Page 7
PACKING SECTION parts List Mark No. Description Part No. Mark No. Description Part No. Package, Pad 792WHA0604 > Cord Set AC See Contrast table (2) Polyethylene Bag See Contrast table (2) Cord, RCA Pin 06CPBA2006 Gift Sheet 791WHA0108 Remote Control VXX2914 Package See Contrast table (2)
2.3 05 DVD MECHA SECTION Cannot supply separately. If the repair is needed, replace the Lubricating Oil LOADER SUB ASS'Y. GYA1001 Daifree GEM1036 Lubricating Oil GYA1001 CD2001 PCB610 (LOADING MOTOR PCB ASS'Y) CD2302 Do not replace the parts. Because, minute adjustments are needed if this condition is disassembled further more.
Page 11
05 DVD MECHA SECTION parts List Mark No. Description Part No. Loading Motor PCB Assy A2F101A610 Gear,Middle 92P100117A > Loading Motor 1515S98004 Pulley,Motor 92P100097A > FEED Motor 1515S98004 Cord Jumper (24P)(CD2001) 122H0O2305 Cord Jumper (CD2302) 122H051602 Insulator (F) 92P200013A Belt,Loading 92P200015A Insulator (R) 92P200016A...
J8004 DIGITAL OUT COAXIAL IC8004 IC8003 Audio DAC Audio LPF J8003 2 ch & AMP V-OUT L AUDIO OUT V-OUT R J8002 S_Y OUT S VIDEO OUT S_C OUT R/CR out J8001 G/Y out B/CB out VIDEO V out POWER PCB ASSY CVBS IC8002 Video Driver...
Page 15
÷ When ordering service parts, be sure to refer to "EXPLODED VIEWS and PARTS LIST" or "PCB PARTS LIST". ÷ The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. ÷...
Page 23
NOTE : THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK. R8070 B8003 MMZ1608R102CT AUDIO DAC 2CH IC8004 PCM1742KEG/2K BCKIN MCLK DATA R8035 (DA) 2.2K LRCKIM JACK MUTE CTL Q8014 KTA1504S_Y_RTK C8068 C8036 0. 1 B ZERO L MUTE CTL R8065...
Page 31
: VIDEO SIGNAL ROUTE : VIDEO SIGNAL ROUTE (R ch) : VIDEO SIGNAL ROUTE (G ch) : VIDEO SIGNAL ROUTE (B ch) : AUDIO SIGNAL ROUTE (L ch) J8101 MRC-021V-07_A R 8114 21PIN_R 220 + - 1% R 8115 21PIN_L 220 + - 1% L8101 21PIN_CTL...
4. PCB CONNECTION DIAGRAM 4.1 LOADING and SW PCB ASSYS NOTE FOR PCB DIAGRAMS : 1. Part numbers in PCB diagrams match those in the schematic 3. The parts mounted on this PCB include all necessary parts for diagrams. several destinations. 2.
5. PCB PARTS LIST NOTES: Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List. mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. When ordering resistors, first convert resistance values into code form as shown in the following examples.
Page 47
Mark No. Description Part No. Mark No. Description Part No. C4034 CC 22 PF 50V CH CS0PCH4H1J C8001 CC 0.1 UF 25V B CS0PB0315K C4035 CC 0.1 UF 25V B CS0PB0315K C8002 CC 1 UF 10V B CS0PB0N16K C4039 CC 1 UF 10V B CS0PB0N16K C8003 CC 1 UF 10V B CS0PB0N16K...
Page 50
Mark No. Description Part No. Mark No. Description Part No. C506 CE 2.2 UF 50V E50HU52R2M IC503 IC PQ070XF01SZH I0GA9XF010 IC504 PS2561AL1-1-V(W) 000220002W C507 CC 0.01 UF 50V F CS0PF0414Z Q501 KTC3875S_Y_RTK TCAA3875SY C508 CC 680 PF 50V CH CS0PCH4U2J C509 CE 10 UF 50V E02LU5100M Q502 KTC3209_Y_AT...
Page 51
Mark No. Description Part No. Mark No. Description Part No. R528 RC 22K OHM 1/4W R002T4223J W24024 JUMPER IN PCB 1230T10001 R529 R,METAL OXIDE 220 OHM 1W R3X181221J W24025 JUMPER IN PCB 1230T07501 R530 RC 560 OHM 1/4W R002T4561J W24026 JUMPER IN PCB 1230T05001 W24027 JUMPER IN PCB 1230T05001...
6. ADJUSTMENT 6.1 WHEN REPLACING DVD DECK WHEN REPLACING DVD DECK [ Removing the DVD Deck ] Before removing Pick Up PCB and DVD PCB connector, short circuit the position shown in Fig. 1 using a soldering iron. If you remove the DVD Deck with no soldering, the Laser may be damaged. [ Installing the DVD Deck ] Remove all the soldering on the short circuit position after the connection of Pick Up PCB and DVD PCB connector.
6.2 TEST MODE POWER ON POWER DVD test disc Test mode remote control (GGV1025) unit (GGF1381) DISC SET <TRAY OPEN> <TRAY CLOSE> OPEN/CLOSE OPEN/CLOSE DVD disc (Player) (Player) TEST MODE: PLAY CHECK An address is displayed <PLAY> DVD, CD TEST Press the play key ) of the normal remote control unit.
6.3 DISC REMOVAL METHOD DISC REMOVAL METHOD AT NO POWER SUPPLY Remove the Top Cabinet and Front Cabinet. (Refer to item 1 of the DISASSEMBLY INSTRUCTIONS.) Rotate the Main Gear in the direction of the arrow by hand. (Refer to Fig. 1) Draw the Tray.
7. GENERAL INFORMATION 7.1 DIAGNOSIS 7.1.1 TEST MODE IN Test Mode Functional Specification 1 Test mode entry In the power ON state, press the [ESC] (A8-5F) key and [TEST / RANDOM] (A8-5E) key in order of the Test mode remote control unit.
7.1.2 DISPLAY SPECIFICATION OF THE TEST MODE Character in bold : Item name : Information display 0 Disc sensing [DSC – ∗ ∗ ∗] 1 Address indication The address being traced is displayed in number. The type of discs loaded is displayed. (as for the DVD, indication of decimal number is possible.) [DVD], [CD ], [VCD], [ DVD : ID indication (hexadecimal number, 8 digits)
7.1.3 FUNCTIONAL SPECIFICATION OF THE SHORTCUT KEY Only during normal playback, the following shortcut keys can be assigned by pressing a required key after pressing the ESC key of the remote control unit. To quit, press the ESC key Remote Control Remote Command Contents Conditions...
7.1.4 SPECIFICATION OF MODEL INFORMATION DISPLAY To display model information : Press the ESC key then the CHAP key. To close the model information display : Press the ESC key. • Display contents AREA : WY REGION : 2 ROM NUMBER YAD5215B Don't care.
7.1.5 FUNCTIONAL SPECIFICATION OF THE SERVICE MODE • Display during Service Mode To enter Service Mode, press the CHP/TIM key while holding the ESC key pressed. To quit, press the ESC key. Service mode display 1 ID Address 2 Error rate (always displayed), in exponential notation ERROR RATE : ∗...
7.1.6 METHOD FOR DIAGNOSING DEGRADATION OF THE LDS ON THE PICKUP ASSY Case when this diagnosis is required : When playback of any disc, including a test disc (DVD: GGV1025, CD: STD-905), cannot be performed How to diagnose In the case mentioned above, degradation of the laser diodes (LDs) mounted on the PICKUP Assy is suspected. Measure the voltage between the two ends of one of the resistors mentioned below.
7.1.7 TROUBLE SHOOTING Symptoms Diagnosis Contents Possible Defective Points The power is not turned on. Check the voltage of AT+3.3V, –28V and FLDC on the POWER POWER PCB ASSY SUPPLY Unit. Are wires of output connector (POWER PCB ASSY) and CP4003 Connector / cable (DVDM Assy) disconnected or damaged ? OPERATION 2 Assy...
Page 62
Symptoms Diagnosis Contents Possible Defective Points Does the voltage of CP2302-pin 3 and pin 1 on the DVD MT Assy A tray cannot be opened. Tray SW change normally ? (An opening screen is Pin 5 (SW2(TRIN)): Tray is fully closed: "L" displayed on the monitor) Pin 3 (SW1(TROUT)): Tray is fully opened: "L"...
7.2 DISASSEMBLY REMOVAL OF MECHANICAL PARTS AND P.C. BOARDS 1-3: DVD DECK (Refer to Fig. 1-3) Short circuit the position shown in Fig. 1-3 using a soldering iron. If you remove the DVD Deck with no 1-1: TOP CABINET/FRONT CABINET/OPERATION soldering, the Laser may be damaged.
REMOVAL OF DVD DECK PARTS NOTE In case of the Traverse Ass'y, install it from (1) to (4) in NOTE order. (Refer to Fig. 2-2-B) 1. Do not disassemble the DVD DECK PARTS except In case of the Traverse Ass'y installation, hook the wire listed parts here.
Page 65
NOTE 2-4: RACK LOADING/MAIN GEAR/PULLEY GEAR (Refer to Fig. 2-4-A) In case of the Pulley Motor installation, check if the value Unlock the support 1 and remove the Gear Pulley. of the Fig. 2-3-B is correct. When installing the wire of the Loading Motor PCB Ass'y, Remove the Gear Main.
Page 66
NOTE 1. In case of the Clamper Ass'y installation, install Feed Motor correctly as Fig. 2-5-B. Gear Motor Plate Clamper Check Lock Clamper Traverse Ass'y Gear Feed Fig. 2-5-B 2-6: HOLDER TRAVERSE/INSULATOR (F)/INSULATOR (R) (Refer to Fig. 2-6-A) Rack Feed Ass'y Gear Middle Remove the Holder Traverse.
Page 67
Switch PCB Ass'y ~ FEED MOTOR ~ WHITE (4) BROWN (3) • Install wire from(1) to (4) in order. ~ SPINDLE MOTOR ~ YELLOW (2) GREEN (1) Fig. 2-7-D Check Hook Traverse Ass'y Check Hook Check Hook Check Hook • Loosen the wirein the direction of the arrows. Fig.
7.3 IC INFORMATION • The information shown in the list is basic information and may not correspond exactly to that shown in the schematic diagrams. List of IC MT1389FE, LA6565, PT6315 MT1389FE (DVD MT ASSY: IC4002) • MPEG / MICON / RF-AMP Pin Arrangement (Top view) AGND DVDA...
Page 69
• MPEG / MICON / RF-AMP Microcomputer Block Diagram Debug CVBS, Y/C 108Mhz Port Component TV Encoder Module Videop RF Amplifier Video DAC Servo IO Servo Motor Processor Video Drive Processor interlacer Spindle Control FLASH MPEG-1/2 Audio JPEG Memory Video Decoder Controller DRAM System...
Page 70
MT1389FE/C2-L (DVD MT ASSY : IC4002) • MPEG/MICON/RF-AMP CPU Pin Function Pin Name Pin Function Pin Name Pin Function Serial interface port 3 data-out AGND – Analog ground Version AD input port 4 DVDA AC coupled input path A GPIO Serial interface port 3 data-in DVDB AC coupled input path B...
Page 71
Pin Name Pin Function Pin Name Pin Function 91 AD7 Microcontroller address/data 7 137 DQM1 Data mask 1 92 A17 Flash address 17 138 RWE# DRAM Write enable, active low 93 IOA0 Microcontroller address 0/IO 139 CAS# DRAM column address strobe, active low 94 DVSS –...
Page 72
Pin Name Pin Function Pin Name Pin Function 189 DACVDDC – 3.3V power pin for VIDEO DAC circuitry Audio left/right channel clock 213 ALRCK Trap value in power-on reset: 190 VREF – Bandgap reference voltage 1:use external 373 191 FS –...
Page 73
Pin Name Pin Function Pin Name Pin Function 239 ADCVDD3 – Analog 3.3V Power for ADC 249 RFGND – Analog Power 240 NC – – – – 250 NC 241 ADCVSS – Analog ground for ADC 251 NC – – –...
Page 74
LA6565 (DVD MT : IC2301) • MOTOR DRIIVE Internal Block Diagram Signal system ground SGND Thermal shutdown circuit (Load output voltage setting) VCONT MUTE VCCP2 MUTE1 Turns the corresponding channal on/off. High : output on, Low : output off VLO– CH2,3,4 MUTE234 44kΩ...
Pin Functions Pin No. Pin Name Pin Descriptions Loading output direction switching (FWD). Loading system logic input. Loading output direction switching (REV). Loading system logic input. V CC 2 Channels 3, 4, and loading power stage power supply VLO – Loading output (–) VLO + Loading output (+)
Page 76
PT6315 (OPERATION 1 ASSY : IC651) • FIP DRIIVE IC Block Diagram SG1/KS1 SG2/KS2 SG3/KS3 SG4/KS4 Control SG5/KS5 SG6/KS6 DOUT Serial SG7/KS7 Data SG8/KS8 Interlace Segment Display Memory SG9/KS9 Driver/ (24bits x 12 Words) SG10/KS10 Grid SG11/KS11 Driver/ SG12/KS12 Key Scan Output SG13/KS13 Tlming Generator...
Page 77
Pin Description Pin Name Description Pin No. LED1 to LED4 LED Output Pin 1 to 4 Oscillator Input Pin A resistor is connected to this pin to determine the oscillation frequency Data Output Pin (N-Channel, Open-Drain) This pin outputs serial data at the falling DOUT edge of the shift clock (starting from the lower bit).
7.4 DISC / CONTENT FORMAT PLAYBACK COMPATIBILITY File structure (may differ): Up to 299 folders on a disc; up to 648 folders and files (combined) within each folder. DV-2850-S...
8. PANEL FACILITIES 8.1 FRONT PANEL SECTION Front panel OPEN/CLOSE TOP MENU MENU STANDBY/ON HOME MENU RETURN 11 10 DV-2850 STANDBY/ON 9 Display Description of the display. Press to switch the player on or into standby. Disc tray OPEN/CLOSE Press to open or close the disc tray. 3 TOP MENU Press to display the top menu of a DVD disc.
8.2 DISPLAY Display 8 and 3 REMAIN Indicates whether a disc is playing or paused. Indicates that the character display is showing the disc or title/chapter/track remain time. Indicates that the character display is showing a DVD chapter number. Character display TITLE Indicates that the character display is showing a DVD title number.
8.3 REMOTE CONTROL Remote control Press to switch the player on or into standby. AUDIO Press to select the audio channel or language. SUBTITLE Press to select a subtitle display. Number buttons TOP MENU Press to display the top menu of a DVD disc. ENTER &...
Page 83
Remote control 2 13 SURROUND 19 RETURN Press to activate/switch off V/SRS TruSurround. Press to return to a previous menu screen. Use for forward slow motion playback, frame Press to open or close the disc tray. advance and forward scanning. 15 ANGLE Press to change the camera angle during Press to jump to the next chapter or track.
7 Jigs list Remote control Name Jig No. Remarks Service Remote Control Unit GGF1381 diagnosis DVD Test Disc (DVD-Video) GGV1025 Check of DVD-Video Press to switch the player on or into standby. CD Test Disc STD-905 Check of CD AUDIO Press to select the audio channel or language.