Page 1
Service SR5005 / N1SG/N1B/U1B /K1B Manual AV Surround Receiver • For purposes of improvement, specifi cations and design are subject to change without notice. • Please use this service manual with referring to the operating instructions without fail. • Some illustrations using in this service manual are slightly different from the actual set.
Page 2
Parts for your MARANTZ equipment are generally available to our National Marantz Subsidiary or Agent. ORDERING PARTS : Parts can be ordered either by mail or by Fax.. In both cases, the correct part number has to be specifi ed.
SAFETY PRECAUTIONS The following check should be performed for the continued protection of the customer and service technician. LEAKAGE CURRENT CHECK Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check.
Page 4
NOTE FOR SCHEMATIC DIAGRAM WARNING: Parts marked with this symbol z have critical characteristics. Use ONLY replacement parts recommended by the manufacture CAUTION: Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the unit is defective.
TECHNICAL SPECIFICATIONS n Audio Section n Tuner section –15 [FM](Note: μV at 75 Ω, 0 dBf = 1 x 10 • Power amplifi er Receiving Range (for U) : Rated output : [FM] 87.5 MHz – 107.9 MHz [AM]520 kHz – 1710 kHz Front : Receiving Range (for N,K)s : 100 W + 100 W (8 Ω, 20 Hz –...
Page 6
SURR.MODE Service Jigs When you repair the printing board, you can use the following JIG (Extension cable kit). Please order to marantz Offi cial Service Distributor in your region if necessary. 8U-110084S : EXTENSION UNIT KIT : 1 Set (Refer to "JIG FOR SERVICING".)
Page 7
DISASSEMBLY • Disassemble in order of the arrow of the fi gure of following fl ow. • In the case of the re-assembling, assemble it in order of the reverse of the following fl ow. • In the case of the re-assembling, observe "attention of assembling" it. •...
• Refer to the table below for a description of the direction in which the photos were taken. • Photographs for which no direction is indicated were taken from above the product. • The Photographs is SR5005 N1B model. The viewpoint of each photograph...
Page 9
(2) Disconnect the connector wires then remove the screws. CP308 STYLE PIN : Loose Direction of photograph: C Direction of photograph: D (3) Cut the wire clamp bands, then disconnect the connector wires and FFC cable. Remove the screws. N4401 FFC cable Please refer to "EXPLODED VIEW"...
Page 10
2. RADIATOR ASSY Proceeding : CABINET TOP FRONT PANEL ASSY RADIATOR ASSY → → (1) Remove the screws. View from bottom (2) Remove the screws. STYLE PIN : Loose Direction of photograph: D Direction of photograph: C...
Page 11
Disconnect the connector wires. RADIATOR ASSY PCB 7CH AMP CP402 CP403 CP405 PCB 7CH AMP CP401 N2706 Please refer to "EXPLODED VIEW" for the disassembly method of each P.W.B included in RADIATOR ASSY.
Page 12
3. PCB REG CNT/PCB REG Proceeding : CABINET TOP FRONT PANEL ASSY RADIATOR ASSY → → PCB REG CNT/PCB REG → (1) Remove the screws. PCB REG CNT PCB REG Direction of photograph: B (2) Disconnect the connector wires and connector board. CP102 CP104 PCB REG CNT...
Page 13
4. HDMI UNIT ASSY Proceeding : CABINET TOP HDMI UNIT ASSY → (1) Cut the wire clamp bands, then disconnect the connector wire and FFC cable. N2501 Direction of photograph: C N4401 FFC cable N2706 HDMI UNIT ASSY CP13A N2004 (2) Remove the screws, then remove the BACK PANEL.
Page 14
(3) Remove the PCB RS232/SIRIUS. Board to board PCB SIRIUS PCB RS232 (4) Disconnect the connector board. Board to board Board to board Board to board PCB HDMI (5) Disconnect the connector board. Board to board PCB VIDEO ASSY...
Page 15
(6) Remove the screws then disconnect the connector. Direction of photograph: A Connector (7) Disconnect the connector board. PCB SIDE CNT PCB FRONT CNT Board to board PCB PREOUT Board to board PCB AUDIO Please refer to "EXPLODED VIEW" for the disassembly method of each P.W.B included in HDMI UNIT ASSY.
Page 16
5. PCB SPK/PCB SMPS Proceeding : CABINET TOP HDMI UNIT ASSY PCB SPK/PCB SMPS → → (1) Remove the screws and SUPPORTER P.C. SUPPORTER P.C. View from bottom (2) Disconnect the connector wire, then remove the screws. Direction of photograph: D SUPPORTER P.C.
Page 17
(3) Disconnect the connector wire, then remove the screws. Remove the PCB SPK/PCB SMPS from the main unit. CP402 CP403 CP405 (4) Disconnect the connector board. PCB SPK PCB SMPS Board to board...
Page 18
SPECIAL MODE Special mode setting button b Press the ON/STANDBY button to turn on while pressing both buttons A and B at the same time. Mode Button A Button B Contents Firmware versions such as Main, Sub, DSP are displayed in μcom/DSP Version display mode STATUS RETURN...
Page 19
1. μcom/DSP Version display mode 1.1. Operation specifi cations μcom/DSP version display mode: When started up, the version information is displayed. Starting up: With the "STATUS" and "RETURN" buttons pressed, press the "ON/STANDBY" button to turn the power on. Now, press the "STATUS" button to the display the 2nd item information on the FL Display. 1.2.
Page 20
2. Errors checking mode (Displaying the protection history) 2.1. Operation specifi cations Error mode (Displaying the protection history): When started up, the error information is displayed. Starting up: ●All model commonness With the "STATUS" and "CURSOR 0 " buttons pressed, press the "ON/STANDBY" button to turn the power on. The error (protection history display) mode is set.
Page 21
2.3. Clearing the protection history There are two ways to clear the protection history, as described below. (1) Start up the error (protection display) mode, display the error, then press and hold in the "ENTER" button for 3 seconds. : T H E R M A L T H E Press and hold in the "ENTER"...
3. DUAL BACKUP MEMORY This product has a Dual Backup Memory function. The conventional Backup functions to memorize, in the EEPROM (U3103) in the circuit, a current setting of the moment the main power is turned off so that it can be restored when it is turned ON again.
Page 23
When you repair the printing board, you can use the following JIG (Extension cable kit). Please order to marantz Offi cial Service. Distributor in your region if necessary. Note: When the connection which is wrong in the JIG (EXTENSION UNIT KIT) is done it becomes cause of damage.
Page 24
(4) Disconnect the connector board. Board to board PCB VIDEO ASSY (5) Remove the screws then disconnect the connector. Connector (6) Disconnect the connector board. PCB SIDE CNT PCB FRONT CNT Board to board PCB PREOUT Board to board PCB VIDEO...
Page 25
(3) PCB HDMI is detached from the chassis, and it puts it into the state turned inside out. Please pave an insulation sheet that is larger than PCB HDMI under PCB. b Connect the ground point of PCB to the chassis with a ground lead or the like. PCB INPUT Ground lead PCB VIDEO...
Page 26
PCB HDMI Insulation sheet PCB INPUT PCB SIDE CNT Connection table of Board to Board Ref. No. Ref. No. 11 pin SIDE CNT N2709 HDMI 25 pin SIDE CNT N2708 HDMI 19 pin CP105 FRONT CNT N2701 HDMI 17 pin CP106 FRONT CNT N2702...
Page 27
ABOUT REPLACE THE MICROPROCESSOR WITH A NEW ONE When replaced of the U-PRO (Microprocessor) or the Flash ROM, confi rm contents of the following. After PWB Name Ref. No. Description Remark replaced DIGITAL U3102 R5F64169DFD SOFTWARE: Main DIGITAL U3301 R5F3650KNFB SOFTWARE: Sub DIGITAL U1903 EN29LV160BB-70TIP...
Page 28
4. Run the DFW Run the "DFW_0002_SR5005_(Rev.1.0.6)" on desktop of PC. 5. Communication check (1) Click the “Check Comm.” button. (2) When connection is good, then you can see the “Communication check OK.” message. (3) If connection is not good, then you can see the “Communication check NG” message. Please confi...
Page 29
6. Download the fi rmware (1) Click the "Load" button. (2) Download the fi rmware from the specifi ed download source to PC. 7. Complete the fi rmware updating (1) Click the “Update” button. (2) When writing of the fi rmware is completed, the power of this unit turns on automatically and you can see the “Update completed”...
Page 30
(i) In case of laptop PC, Use the AC adaptor. Confi rming the fi rmware’s number after upgraded After completion of the updating operation, the new version number can confi rmed by starting up the SR5005 according to the following procedure.
Page 35
ADJUSTMENT Audio Section Idling Current Required measurement equipment: DC Voltmeter 1. Preparation (1) Avoid direct blow from an air conditioner or an electric fan, and adjust the unit at normal room temperature 15 °C ~ 30 °C (59 °F ~ 86 °F). (2) Presetting •...
TROUBLE SHOOTING 1. POWER 1.1. Power not turn on Power not turn on. When the power turned on, Is the fuse blown? Refer to 1.2.Fuse is blown. does the FLD on the front panel light? Check for damage Is a DC 5V voltage output in the SMPS B'D Is a DC 5V voltage being when the cord supplying the...
2. Analog video MONITOR OUT (CVBS) output NG Input COMPONENT Input CVBS Function : SAT Function : SAT To A Not output MONITOR OUT (COMPONENT) output NG Input COMPONENT Input CVBS Function : DVD Function : SAT To B Not output HDMI OUT outpu NG Input COMPONENT Input CVBS...
Page 38
Input CVBS Check power supply voltage. V+5V : N2004-4pin REGULATOR B'D fl aw. V-5V : N2004-1pin Check on set value of each IC. HDMI B'D L2701 : Check I C communication HDMI B'D fl aw. waveforms. L2702 : Check I C communication waveforms.
Page 39
Input COMPONENT Check power supply voltage. V+5V : N2004-4pin REGULATOR B'D fl aw. V-5V : N2004-1pin Check on set value of each IC. HDMI B'D L2701 : Check I C communication HDMI B'D fl aw. waveforms. L2702 : Check I C communication waveforms.
Page 40
Check HDMI output setting, referring to the (5) Is the BD/DVD player's HDMI output setting correct? BD/DVD player's operating instructions. (6) When using a marantz BD/DVD player's, is the fl uorescent display tube's "HDMI" indicator lit? If using a non-marantz BD/ DVD player's, proceed to "YES".
Page 41
BD/DVD player, is the FL HDMI connector (K1001/K1002/K1003/ from the HDMI connector display's "HDMI" indicator lit? K1004)15pin(DDC_CLK)/16pin(DDC_DATA)? (K1001/K1002/K1003/ If using a non-marantz BD/ Is 1pin/3pin/4pin/6pin/7pin/9pin/10pin/12pin of K1004) to the U1001 is DVD player, proceed to HDMI connector (K1501) terminated by 3.3V and defective.
Page 42
Check operation of each device. (AMP source : BD / Video input of player : 480P / Connect the TV.) Check operation of U1001. (18) Check power supply. Is 1.8V supplied to C1019/C1053/C1037/L1003? The power supply circuitry is defective. Is 3.3V supplied to C1112/C9032/C1124/C1122? (19) Check xtal oscillator.
Page 45
4. AUDIO 4.1. AUDIO CHECK AUDIO OUTPUT : NG INPUT SURROND MODE SOURCE CHECK1 Check ANALOG AUDIO BLOCK. ANALOG 2CH DIRECT ANALOG INPUT SURROND MODE SOURCE CHECK2 Check Digital AUDIO BLOCK. COAX or OPT Legacy(PCM or DolbyDigital or dts…) INPUT SURROND MODE SOURCE CHECK3 Check via AD.
Page 46
4.2. Power AMP (7CH AMP B'D) No sound is output. The protector operates. Is the power transistor open or short circuit? Replace the power transistor. 2SB1647/2SD2560 Is the emitter resistance of the power transistor open? Replace the emitter resistance. 0.47Ω Is the base resistance of the power transistor open? Replace the base resistance.
4.3. Analog audio No sound is output Is the voltage of ±8V supplied to The power supply of ±8V is repaired. AV B'D CP8? Is the audio signal transmitted to The power amplifi er is repaired. AV B'D CN401? Connect the connectors properly. Is the serial data for electronic volume Is the connector correctly connected transmitted to AV B'D CP11?
Page 65
SIDE_CNT (COMPONENT SIDE) SIDE_CNT (FOIL SIDE) IC109 PQ033DNA1ZPH J101 CP802 M3.3V 232IMO 232OMI M/DGND BKT101 AZ4580 7028-06943-401-0 CP13A SIDE CNT_B'D AC MUTE DET AC MUTE DET X2 VOLT DET X2 VOLT DET DA+5V DA+5V TRG+15V TRG+15V TRG_GND TRG_GND A+8V A+8V A-8V A-8V AGND...
Page 66
FRONT (COMPONENT SIDE) FRONT B'D 7020-06962-000-0S J332 SR5005 : JUMPER {RefDes} (SR6005) C312 SR6005 : OPEN {Value} 10/50(5*7) R415 J378 CN300 J341 J379 {RefDes} {Value} J340 INPUT (SR5005) LED301 SELECTOR J330 PURE R420 VEC304 VEC302 DIRECT VOLUME R413 R427 M-DAX...
Page 67
FRONT (FOIL SIDE) R430 - SR5005 ONLY FRONT B'D R431 - SR6005 ONLY 7020-06962-000-0S SR5005 : 0 SR6005 : OPEN C346 C350 Q317 R363 C361 Q314 C306 R333 R421 C324 Q313 Q309 CLAMP R414 Q312 Q310 R360 R_NO. SR5005 SR6005...
Page 84
SR6005 SR7005 SR7005 ONLY ONLY ONLY TO FRONT CNT TO FRONT CNT PAGE 7(J5) PAGE 7(H5) TO SIDE CNT PAGE 6(G7) CN3000 R3000 OPEN C125Z2-33P AUDIO B’D CX3001 AUDIO IN CX3000 R3001 100K C125Z2-13P C125Z2-19P R3002 100K IC3000:B AZ4580 R3004 C3000 R3003 100K...
Page 85
P_HD/TU_RST/ST R4328 C4134 TU_GPL02 P_TU_GPL02/TUNED 10/50 L4002 R4323 100K 75J-207CX R4330 OPTION_D C4142 100N-K CHASSIS OPTION_B MODEL SR5005 SR6005 SR7005 REGION R4332 OPTION A Q4101 OPTION B Q4100 KRA111S KRC102S CP4003 OPTION C OPTION D Q4102 KRC102S TUNER_L OPTION E...
Page 87
R4154 R4157 R4158 R4155 OPEN OPEN OPEN OPEN R4153 C4065 R4156 C4066 OPEN OPEN R4159 OPEN OPEN R4160 OPEN OPEN Q4052 Q4053 OPEN OPEN R4167 R4168 OPEN OPEN IC4002:A IC4003:A Q4050 Q4051 OPEN Q4054 OPEN Q4055 OPEN OPEN IC4001:A OPEN OPEN R4171 R4173...
Page 88
PAGE 7 (C5) PAGE 7(E5) PAGE 7 (A5) PAGE 5 (B3) N2005 TO FRONT CNT B’D TO FRONT CNT B’D TO FRONT CNT B’D TO REGULATOR B’D OPEN SR7005 SR6005 SR5005 CHIP_J D2001,D2002 KDS160 KDS4148U KDS4148U D2005,D2006 C2006-C2008 C2047,C2060 10/50 22/16 22/16...
Page 89
BD7628F-E2 K1002 OPEN OPEN 33uH SR7005:OPEN C1011 IN4CB Q1002 R1059 R1011 KRC111S SR7005_only SR7005_only OPEN K1002 OPEN C1012 IN4CR SR5005 SR5005 SR5005 SR5005 SR7005,SR6005 U(E3) N(E2) K(E1C) F(JP) R1060 R1012 X1002 OPEN 17.734M 17.734M OPEN OPEN OPEN Q1001 OPEN KRA102S...
Page 90
TO COMPONENT TO COMPONENT N3003 OPEN CB-G MONITOR CR-G MONIL1 LINE1 MONIL2 LINE2 MONIL3 LINE3 N3001 OPEN CB-G CR-G LINE1 VIN1L1 LINE2 VIN1L2 LINE3 VIN1L3 N3002 OPEN CB-G JAPAN LINEA LINEB ON CHANNEL CR-G Q3001 LINE1 VIN2L1 ASPECT_H OPEN VIDEO-2 LINE2 VIN2L2 LINE3...
Page 96
TO DIR/PLD TO SUB CPU C9151 1000P C9152 1000P C9153 DA+5V DA+7V DA-7V 1000P C9154 1000P R2135 R2136 C9155 C9059 C9074 C9068 C9088 1000P OPEN OPEN OPEN OPEN C9073 C9093 DA+5V OPEN OPEN DGND DAGND A+7V C9078 C9098 DA+7V C2107 0.1/10 R2161 OPEN...
Page 97
TO MAIN CPU NET3.3V DIGITAL NET1.8V SUPPLY DGND R2311 4.7K R2348 R2312 4.7K C2356 U2305 C2359 1/10 AK4424ET 1/10 C2360 JTAG 4.7/6.3 N2301 L2303 OPEN VSS2 BLM21PG221 R2332 TCKUSB CVDD MCLKUSB GND_D1 MCLK TDOUSB BCKoUSB BICK VSS1 DATAoUSB SDTI R2334 TMSUSB LRCKoUSB LRCK...
Page 104
WIRING DIAGRAM AC CORD SIRIUS B'D SPK B'D HDMI B'D RS232 B’D VIDEO B'D FRONT CNT B'D AUDIO IN B'D MAIN TRANS PRE OUT B'D REG_CNT B'D (S2,S4) (S1) REG B'D 7808 7908 7805 7905 7805 2388 2P WIRE(SPK OUT SB) 7CH AMP B'D (S5,S6) FRONT B'D...
Page 105
P x2 37 x3 D x3 D x2 35 x4 T x2 34 x4 T x4 T x3 WARNING: U x1 SR5005 Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by D x2 the manufacturer.
Page 107
Ref.No. Part No. Part Name Remarks Q'ty Personal notes: HEAT SINK MAIN 2120211788000S SHEET RATING CHASSIS 1210211269000S BRACKET H SINK 4010056906010S BRACKET SMPS 4010214886000S CUSHION FOOT 4050211175000S 00M46BW057210 FOOT FRONT 4007210321000S CHASSIS MAIN 3200213506200S SUPPORTER PCB 4070001601010S BRACKET SIDE 4010210686000S SUPPORTER P.C.
Page 108
PACKING VIEW s Ref.No. Part No. Part Name Remarks Q'ty BATTERY DRY G670001R50210S SHIPPING LABEL 5507000007500S PE SHEET 6327040059000S N1B,N1SG,K1B model 324810004004M SETUP MIC AUDYSSEY MIC ACM1H M040000310060S LABEL COLOR N1SG 5507000004600S 9 10 30 PAD BOX BACK 6240210730000S 90M-ZC000470R CORD ASSY L068125130010S 90M-ZC000600R...
Page 109
SEMICONDUCTORS Only major semiconductors are shown, general semiconductors etc. are omitted to list. The semiconductor which described a detailed drawing in a schematic diagram are omitted to list. 1. IC's R5F64169DFD (HDMI :U3102) (Note 1) IIO0_0 / IIO1_0 / D8 / P1_0 P4_4 / CS3 / A20 / CTS6 / RTS6 / SS6 AN0_7 / D7 / P0_7 P4_5 / CS2 / A21 / CLK6...
Page 110
R5F64169DFD Terminal Functions Pin Name Synbol I/O Type Pullup STBY stop Function 1 P96/(TXD4) SIRIUS RST(U) O/L Terminal for SIRIUS control(U) 2 P95/(CLK4) HDRADIO RST/TU RST/ST IND O/L HDRADIO/TUNER KST-MW/KST-MT control 3 P94/(CTS4)/TB4IN RC IN O/(I) /M3.3 RC-5 input terminal 4 P93/(CTS3)/TB3IN FLASHER IN O/(I)
Page 111
92 P30/(A8) MIC DET SW3VPu O/L Terminal for MIC detection 93 VSS SOURCE DIRECT LED(NR1601) 94 P27/(A7) DIRECT LED /PURE DIRECT LED(SR5005)Control terminal(ON="H") 95 P26/(A6) O/L NC 96 P25/(A5) O/L NC 97 P24/(A4) STANDBY(CEC) LED O/L POWER LED control terminal(ON="H")/STANDBY(CEC) LED)
Page 112
Pin Name Synbol I/O Type Pullup STBY stop Function 126 P154/(TXD6) BT LINK SW3VPu O/L Bluetooth detection terminal 127 P153 USB PDN NET3VPu O/L USB(TELECHIPS) control terminal 128 P152/RXD7 129 P151/CLK7 130 VSS 131 P150/TXD7 132 VCC 133 P107/(AN7)/(KI3) ZVOL STB O/L ZONE VOL(NJW1194) control 134 P106/AN6/KI2 KEY3...
Page 114
R5F3650KNFB Terminal Functions Pu/Pd PURE Pin Name Synbol I/O Type Det P.OFF Function (Int.) (Ext.) STBY 1 P94 2 P93 DIR CE DIR control pin (LC89058W-VF4A) 3 P92/SOUT3 DIR DIN DIR control pin (LC89058W-VF4A) 4 P91/SIN3 DIR DOUT DA3.3Pu DIR control pin (LC89058W-VF4A) 5 P90/CLK3 DIR CLK DIR control pin (LC89058W-VF4A)
Page 115
Pu/Pd PURE Pin Name Synbol I/O Type Det P.OFF Function (Int.) (Ext.) STBY 58 P32 DAC MDI DAC control pin (ASK4358) 59 P31 DAC MC DAC control pin (ASK4358) 60 VCC +3.3V 61 P30 DAC MS DAC control pin (ASK4358) 62 VSS 63 P27 DAC RST...
Page 117
LC89058W-E (HDMI : U1706) 35 34 33 32 31 30 29 28 27 26 25 SDIN SLRCK SBCK RDATA XMODE RLRCK DGND LC89058W-E DV DD DGND DV DD RBCK GPIO0 RMCK GPIO1 GPIO2 AGND GPIO3 AV DD RXOUT2 * : Pull-down resistor internal at no selection Pin Functions RXOUT1 RX0-6 input S/PDIF through output pin 1...
Page 118
Pin No. Name Function DGND Digital GND DV DD Digital power supply (3.3V) XMCK Oscillation amplifier clock output pin XOUT Output pin connected to the resonator External clock input pin, connected to the resonator (12.288MHz/24.576MHz) DV DD Digital power supply DGND Digital GND MOUT...
Page 119
ADSP21367KSWZ2A (HDMI : U1901) PIN 1 INDICATOR TOP VIEW (PINS DOWN) ADSP21367KSWZ2A Terminal Function Pin No. Signal Pin No. Signal Pin No. Signal Pin No. Signal DATA28 DATA27 IOVDD IOVDD ADDR0 SDCAS IOVDD ADDR2 SDRAS DATA26 ADDR1 SDCKE DATA25 ADDR4 SDWE DATA24 ADDR3...
Page 121
W9864G2IH-6 Block diagram CLOCK BUFFER CONTROL SIGNAL GENERATOR COMMAND DECODER COLUMN DECODER COLUMN DECODER CELL ARRAY CELL ARRAY BANK #0 BANK #1 MODE REGISTER SENSE AMPLIFIER SENSE AMPLIFIER ADDRESS BUFFER DATA CONTROL CIRCUIT BUFFER DQ31 COLUMN REFRESH COUNTER COUNTER DQM0~3 COLUMN DECODER COLUMN DECODER CELL ARRAY...
Page 122
W9864G2IH-6 Pin description PIN NUMBER PIN NAME FUNCTION DESCRIPTION Multiplexed pins for row and column address. Row address: A0−A10. Column address: A0−A7. 24, 25, 26, 27, 60, 61, 62, Address A0−A10 A10 is sampled during a precharge command to 63, 64, 65, 66 determine if all banks are to be precharged or bank selected by BS0, BS1.
Page 127
Signal Name Pin# Type Description – TCC8600 VDDI PWR Digital Power for Internal Core (1.8V) VDDI PWR Digital Power for Internal Core (1.8V) VDDI PWR Digital Power for Internal Core (1.8V) VDDI PWR Digital Power for Internal Core (1.8V) VDDADC PWR Analog Power for ADC (3.3V) VDDPLL PWR Analog &...
Page 128
Pin# Signal Name Type Description – TCC8600 XA[16] / SD_nRAS / ND_ALE External Bus Address Bit [16] / SDRAM RAS signal / ALE for NAND Flash XA[17] / ND_CLE External Bus Address Bit [17] / CLE for NAND Flash XA[18] / DQM[0] External Bus Address Bit [18] / Data I/O Mask 0 XA[19] / DQM[1] External Bus Address Bit [19] / Data I/O Mask 1...
Page 129
Pin# Signal Name Type Description – TCC8600 GPIO_D[17] GPIO_D[17] / I2C SCL GPIO_D[18] / UART1TXD GPIO_D[18] / UART1 TX Data. Internal pull-up resistor enabled at reset. GPIO_D[19] / UART1RXD GPIO_D[19] / UART1 RX Data. Internal pull-up resistor enabled at reset. GND Digital Ground GPIO_D[20] / UART1 RTS Output (active low).
Page 139
PARTS LIST OF P.C.B. UNIT s zParts for which "nsp" is indicated on this table cannot be supplied. zThe parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions. Note: The symbols in the column "Remarks" indicate the following destinations. U : North America model N : Europe model K : China model...
Page 147
PCB REG_CNT ASS'Y Ref. No. Part No. Part Name Remarks Q'ty SEMICONDUCTORS GROUP IC103 00D2630553006 IC NJM7805FA J126780500130S IC104 00D2630554005 IC NJM7905FA J126790500020S IC105 00D2630553006 IC NJM7805FA J126780500130S IC106 00D2630810008 IC NJM7808FA J126780800030S IC107 00D2630503001 IC NJM7908FA J126790800020S IC108 963239010770S IC NJM2388F09 N1B, N1SG, K1B J126238800090S...
Page 153
PCB VIDEO ASS'Y Ref. No. Part No. Part Name Remarks Q'ty New SEMICONDUCTORS GROUP U1001 00D9630116307 IC LC74781-9013-E J170747810010S U1003 232810005504S IC BD7628F-E2 J127762800010S U2003 235810046603S IC AVDM2000(NJW1327) J171132700010S U2004 231310009508S IC PQ033DNA1ZPH J126033010010S Q1001 00D9630120704 TR KRA102S(PB) N1B, N1SG, K1B J520010200210S Q1002 00D9600296309 TR KRC111S (NM...
Page 159
PCB HDMI ASS'Y Ref. No. Part No. Part Name Remarks Q'ty SEMICONDUCTORS GROUP U1001 IC ADV7840 J040784005510S U1301 00D2622557900 IC SN74LV14APWR J040741400180S U1302 IC ANALOG ABT1030 J080103005510S NOTE : U1303 963244012410S IC IS42S16400F-6TL J001421640060S When update Firmware, U1501 963239010410S IC ADV7511BSTZ-225 J040751100010S please confi...
Need help?
Do you have a question about the SR5005 and is the answer not in the manual?
Questions and answers