1 Safety Precautions 1.1. General Guidelines 1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit. 2. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed.
2 Warning 2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatically Sensi- tive (ES) Devices Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Elec- trostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor [chip] components.
2.2. About lead free solder (PbF) Note: Lead is listed as (Pb) in the periodic table of elements. In the information below, Pb will refer to Lead solder, and PbF will refer to Lead Free Solder. The Lead Free Solder used in our manufacturing process and discussed below is (Sn+Ag+Cu). That is Tin (Sn), Silver (Ag) and Copper (Cu) although other types are available.
3 Service Navigation 3.1. Service Hint Board Name Function A-Board Speaker out, AV Terminal, HDMI in, SD Card, PC in, iPod, Digital Signal Processor, Nile-Tcon, Tuner V-Board Remote Receiver, LED P-Board Power (AC/DC), DC-DC Control Panel Assy Control Button, Power switch Non serviceable Control Panel Assy should be exchanged for service.
4 Specifications Power Source AC 110-127 V, 60 Hz Power Consumption Maximum 153 W Standby Condition 0.3 W Display panel Aspect Ratio 16:9 Visible screen size 37 inch class (37.0 inches measured diagonally) (W × H × Diagonal) 32.2 inch × 18.1 inch × 37.0 inch (819 mm × 460 mm × 940 mm) 1,049,088 (1,366 (W) ×...
5 Service Mode 5.1. How to enter into Service Mode While pressing [VOLUME ( - )] button of the main unit, press [INFO] button of the remote control three times within 2 seconds. 5.1.1. Key command [1] button...Main items Selection in forward direction [2] button...Main items Selection in reverse direction [3] button...Sub items Selection in forward direction [4] button...Sub items Selection in reverse direction...
Contents of adjustment mode 5.1.2. • Value is shown as a hexadecimal number. • Preset value differs depending on models. • After entering the adjustment mode, take note of the value in each item before starting adjustment. Main item Sub item Sample Data Remark ADJUST...
5.2. SRV-TOOL 5.2.1. How to access 1. Select [SRV-TOOL] in Service Mode. 2. Press [OK] button on the remote control. 5.2.2. Display of SOS History SOS History (Number of LED blinking ) indication. From left side; Last SOS, before Last, three occurrence before, 2nd occurrence after shipment, 1st occurrence after shipment. This indication except 2nd and 1st occurrence after shipment will be cleared by [Self-check indication and forced to factory ship- ment setting].
5.3. Hotel mode 1. Purpose Restrict a function for hotels. item Function 2. Access command to the Hotel mode setup menu Mode Select hotel mode off/on In order to display the Hotel mode setup menu, please Input Select input signal modes. enter the following command (within 2 second).
5.4. Data Copy by SD Card 5.4.1. Purpose (a) Board replacement (Copy the data when exchanging A-board): When exchanging A-board, the data in original A-board can be copied to SD card and then copy to new A-board. (b) Hotel (Copy the data when installing a number of units in hotel or any facility): When installing a number of units in hotel or any facility, the data in master TV can be copied to SD card and then copy to other TVs.
Page 13
5.4.3. Data copy from TV set to SD Card 1. Turn on the TV set. 2. Insert SD card with a startup file (pwd file) to SD slot. On-screen Display will be appeared according to the startup file automatically. 3. Input a following password for (a) or (b) by using remote control. (a) For Board replacement : 2770 (b) For Hotel : 4850 Data will be copied from TV set to SD card.
Page 14
5.4.4. Data copy from to SD Card to TV set 1. Turn on the TV set. 2. Insert SD card with Data to SD slot. On-screen Display will be appeared according to the Data folder automatically. 3. Input a following password for (a) or (b) by using remote control. (a) For Board replacement : 2771 (b) For Hotel : 4851 Data will be copied from SD card to TV set.
6 Troubleshooting Guide Use the self-check function to test the unit. 1. Checking the IIC bus lines 2. Power LED Blinking timing 6.1. Check of the IIC bus lines 6.1.1. How to access Self-check indication only: Produce TV reception screen, and while pressing [VOLUME ( - )] button on the main unit, press [OK] button on the remote control for more than 3 seconds.
6.2. Power LED Blinking timing chart 1. Subject Information of LED Flashing timing chart. 2. Contents When an abnormality has occurred the unit, the protection circuit operates and reset to the stand by mode. At this time, the defective block can be identified by the number of blinks of the Power LED on the front panel of the unit.
6.3. No Power First check point There are following 2 states of No Power indication by power LED. 1. No lit 2. Red is lit then turns red blinking a few seconds later. (See 6.2.)
7 Disassembly and Assembly Instructions 7.1. Pedestal 7.3. AC cord 1. Lay down the unit so that the rear cover faces upward. 1. Remove the screw and Remove the AC cord bracket. 2. Remove the 4 screws. 2. Remove the bushing of the AC cord from the AC cord 3.
7.5. Side AV bracket 7.7. Control panel 1. Remove the 1 screw (D). 1. Disconnect the connector (K1). 2. Remove the 1 screw (E). 2. Remove the 2 screws. 3. Remove the side AV bracket. 3. Remove the control panel. 7.6.
7.9. Metal bracket A-Board 3. Remove the Metal bracket P-Board-S. 4. Remove the clampers. 1. Remove the 4 screws. 2. Remove the Metal bracket A-Board L/S. 7.10. Bracket IP 1. Remove the 3 screws. 2. Remove the Bracket IP. 7.11. VESA metal 1.
7.12. Metal support 7.14. LCD Panel 1. Remove the 6 screws. 1. Remove the 6 screws. 2. Remove the Metal supports (L, R). 2. Remove the LCD panel. 7.13. Metal bracket 1. Remove the 4 screws (F). 2. Remove the 3 screws (G). 7.15.
8 Measurements and Adjustments 8.1. Voltage chart of P-board VOLTAGE TEST POINT SPECIFICATION (Reception state) TP7952, TP7953 18 ± 2 V DTV12V TP7954, TP7955 12.2 ± 0.6 V TUNER6V TP7956 6.1 ± 0.3 V 8.2. Voltage chart of A-board VOLTAGE TEST POINT SPECIFICATION (Reception state)
9 Block Diagram 9.1. Main Block Diagram DIGITAL SIGNAL PROCESSOR TMDS DATA HDMI1 TMDS DATA HDMI I/F HDMI2 RECEIVER SD CARD DATA TMDS DATA SD CARD SD CARD DATA (SIDE) HDMI3 SLOT IFD_OUT FRONT END Nile-TCON SIF_OUT PROCESSOR DDR2 TUNER EEPROM STB5V STB3.3V...
9.2. Block (1/2) Diagram DIGITAL SIGNAL PROCESSOR POWER LED REMOTE RECEIVER C.A.T.S. SENSOR D2500 SN2501 POWER LED C.A.T.S. POWER LED(R) R_LED_ON SENSOR C.A.T.S. C.A.T.S. RM2501 REMOTE IN REMOTE IN SUB5V REMOTE SUB+5V RECEIVER STB3.3V STB+3.3V SOUND15V DTV12V KEYSCAN1 KEYSCAN1 CONTROL PANEL ASSY STB5V KEYSCAN3 KEYSCAN3...
10 Wiring Connection Diagram 10.1. Caution statement. Caution: Please confirm that all flexible cables are assembled correctly. Also make sure that they are locked in the connectors. Verify by giving the flexible cables a very slight pull. 10.2. Wiring...
12 Printed Circuit Board 12.1. P-Board P-BOARD (FOIL SIDE) TXN/P10QNM R L 7 1 0 3 R L 7 1 0 2 R 7 0 3 0 Q 7 0 3 2 R L 7 1 0 1 D 7 0 4 0 C 7 9 5 0 C 7 9 5 1 D 7 0 4 1...
Page 50
P-BOARD (COMPONENT SIDE) TXN/P10QNM R L 7 1 0 1 R L 7 1 0 2 R L 7 1 0 3 Z A 7 0 0 2 R 7 5 0 2 J 2 1 7 J 3 0 4 Z A 7 0 0 0 Z A 7 0 0 1 C 7 5 1 4...
Page 52
A-BOARD (COMPONENT SIDE) TXN/A10QNMS JS1000 JS1001 JS1002 R4621 JS1003 JS1004 JS1005 A 1 3 JS1006 JS1007JS1008 G ( G A ) H ( H A ) J ( J A ) JS1010 JS1013 JS1022 JS1025 JS1011 JS1014 JS1023 JS1026 L8501 K ( K A ) L ( L A ) M ( M A )
12.3. V-Board V-BOARD (FOIL SIDE) TXN/V10QMMM T P 2 5 0 7 T P 2 5 0 0 T P 2 5 0 2 TP2507 TP2500 T P 2 5 0 1 TP2502 TP2501 TP2506 T P 2 5 0 4 P b F T P 2 5 0 3 TP2503...
13.2. Electrical Replacement Parts List 13.2.1. Replacement Parts List Notes...
Page 60
13.2.2. Electrical Replacement Parts List Safety Ref. No. Part No. Part Name & Pcs Remarks Description Safety Ref. No. Part No. Part Name & Pcs Remarks C2501 F2G0J470A019 E 47UF 6.3V Description C2502 F1G1C103A116 C 0.010UF, K, TXN/A10QNMS CIRCUIT BOARD A (RTL) C2505 F1H1C104A143 C 0.1UF, K, 16V...
Page 61
Safety Ref. No. Part No. Part Name & Pcs Remarks Safety Ref. No. Part No. Part Name & Pcs Remarks Description Description C4825 F1G1A105A047 C 1UF, K, 10V C7301 ECQE6103KFW P 0.01UF, J,630V C4826 F1G1H1020008 C 1000UF, 50V C7302 F1A3A101A060 C 100PF, J, 1KV PAVCA C4827 ECJ1VB0J105K C 1UF, K, 6.3V...
Page 62
Safety Ref. No. Part No. Part Name & Pcs Remarks Safety Ref. No. Part No. Part Name & Pcs Remarks Description Description C8029 F1G1E153A103 C 0.015UF, Z, PAVCA C8305 F1G1H221A541 C 220UF, 50V C8306 F1G1H152A571 C 1500UF, 50V C8030 F1J1A106A087 C 0.010UF, K, C8307 F1G1H222A571 C 2200UF, 50V C8308...
Page 63
Safety Ref. No. Part No. Part Name & Pcs Remarks Safety Ref. No. Part No. Part Name & Pcs Remarks Description Description D5770-72 B0JCPG000030 DIODE IC4700 C1ZBZ0004161 IC D7001,02 D4EAC6210002 VARISTOR IC4701 C1ZBZ0004127 IC IC4800 C0DBZYY00343 IC D7030 B0FBAT000008 DIODE IC4802 C0FBBF000074 IC D7040...
Page 64
Safety Ref. No. Part No. Part Name & Pcs Remarks Safety Ref. No. Part No. Part Name & Pcs Remarks Description Description R2218 D0GA680JA015 M 47 OHM, J,0.063W LF7001-03 G0B103H00009 CHOKE COIL R2223 D0GA680JA015 M 47 OHM, J,0.063W K1KY02A00001 2P CONNECTOR PAVCA R2226,27 D0GAR00Z0001 C 0 OHM, 0.063W...
Page 65
Safety Ref. No. Part No. Part Name & Pcs Remarks Safety Ref. No. Part No. Part Name & Pcs Remarks Description Description R2532 D0GAR00Z0001 C 0 OHM, 0.063W R3249 ERJ2GEJ221 M 220 OHM, J,0.063W R2542 D0GAR00Z0001 C 0 OHM, 0.063W R3250 D0GA472JA015 M 4.7KOHM, R2700...
Page 66
Safety Ref. No. Part No. Part Name & Pcs Remarks Safety Ref. No. Part No. Part Name & Pcs Remarks Description Description R4782 D0GA182JA015 M 1.8KOHM, R4942 D0GA223JA015 M 22K OHM J J,0.063W 0.063W R4791 D0GDR00Z0002 M 0 OHM, 1/10W R4943 D0GA473JA015 M 47 OHM, J,0.063W...
Page 67
Safety Ref. No. Part No. Part Name & Pcs Remarks Safety Ref. No. Part No. Part Name & Pcs Remarks Description Description R5697 ERJ3GEYJ332 M 3.3KOHM,J,1/ R7402 ERJ12YJ474 M 470KOHM, 1/2W R7403,04 ERDS1FJ3R3 C 3.3 OHM, J,1/ R5701 D1BA20010002 M 2KOHM, 1/10W R5702 D1BA1001A014 M 1KOHM, 1/10W R7405...
Page 68
Safety Ref. No. Part No. Part Name & Pcs Remarks Safety Ref. No. Part No. Part Name & Pcs Remarks Description Description R7851,52 D0GD101JA036 M 100 R8305 D0GA101JA015 M 100 OHM, OHM,J,0.25W J,0.063W R7853 D0GD102JA036 M R8306 D0GA222JA015 M 2.2KOHM, 1.0KOHM,J,0.25W J,0.063W R7860,61...
Page 69
Safety Ref. No. Part No. Part Name & Pcs Remarks Description R8557 D0GA472JA015 M 4.7KOHM, J,0.063W R8560 D0GA472JA015 M 4.7KOHM, J,0.063W R8851 D1BA2201A014 M2.2 KOHM, 1/10W R8852 D0GAR00Z0001 C 0 OHM, 0.063W R8853 D1BA1001A014 M 1KOHM, 1/10W R9901 ERJ2GEJ103 M 10KOHM, J,0.063W R9902 ERJ2GEJ102X...
Need help?
Do you have a question about the TC-L37X2 and is the answer not in the manual?
Questions and answers