Fluance DB10 Instruction Manual
High performance subwoofer
Hide thumbs
Also See for DB10:
- Quick start manual (4 pages) ,
- User manual ,
- Quick start manual (8 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Fluance DB10
Summary of Contents for Fluance DB10
- Page 1 High Performance Subwoofer DB10 Instruction Manual Thank you for your purchase of this Fluance product. Please read this manual carefully before using the product to ensure proper use. Keep this manual in a safe place for future reference. fluance.com...
- Page 2 Today, Fluance expands on this vision and takes its approach to a new level. With our dedicated team, Fluance assures its products...
-
Page 3: Table Of Contents
Additional Settings ............................6 Crossover Settings ............................ 6 Auto Setting ..............................7 Phase Setting ............................... 7 FAQ ................................... 8 Troubleshooting ..............................9 Specifications ..............................10 Fluance Warranty ..............................11 Warranty Information ..........................11 Important Safety Instructions ........................12 FCC & IC Information ............................13... -
Page 4: What's Included
Phase – REVERSE / NORMAL (Adjust to ensure the DB10 is in phase with the rest of your speaker system. The DB10 will be in phase if the bass response sounds full and balanced.) LFE / Low Level Input –... -
Page 5: First Time Setup
Step One Place the Subwoofer in the most optimal position. Important! Fluance recommends having the woofer face the listener while being positioned near the front channel speakers in a corner if possible. Step Two Step Three Attach the Subwoofer Cable to the... -
Page 6: Step Four (Optional)
Set the Power Switch to Speaker Wire to the channel outputs either ON or AUTO. of your choice on the home theater receiver. Refer to receiver manual for setup instructions. DB10 SPEAKER OUTPUT DB10 Receiver Additional Settings Crossover Settings The Volume/Crossover settings can be adjusted with the Volume/Crossover knob located on the back panel of the Subwoofer. -
Page 7: Auto Setting
1KHz signal requires 5mV. Phase Setting If your speaker system or DB10 is out of phase, it means that the driver/woofer is moving in the opposite direction of the other drivers/woofers. This causes frequencies to be canceled out, which can result in a poor listening experience. By adjusting the phase setting of the DB10, you can ensure the DB10’s woofer is moving in the same... -
Page 8: Faq
What is the purpose of the speaker wire inputs? The speaker wire inputs can be used as an alternative to connect your DB10 to your home theater receiver, however, Fluance recommends using the LFE/Low Level input connected via subwoofer cable. LFE (Low Frequency Effect) refers to a channel specifically intended for deep, low-pitched sounds ranging from 3-120Hz. -
Page 9: Troubleshooting
Troubleshooting Issue Troubleshooting Steps • Ensure the subwoofer is plugged into a known good power source • Confirm that the subwoofer power switch is set to ON or No Power AUTO • Ensure the Power LED is lit • Ensure the subwoofer has power and that the PowerLED is lit Green. -
Page 10: Specifications
Specifications Specifications DB10 Front Firing Powered Subwoofer with Integrated Speaker Configuration Amplifier Low Frequency Driver 10 Inch Polypropylene with Rubber Surround Amplifier Power Peak 120W / RMS 45W Low-Pass Crossover Range 45Hz – 180Hz Frequency Response 20Hz – 180Hz Inputs... -
Page 11: Fluance Warranty
Warranty Period The Fluance products listed below are warranted for parts and labor for the stated period from the date of original purchase and are subject to the terms and conditions of the warranty. -
Page 12: Important Safety Instructions
Important Safety Instructions WARNING: WA R N I N G TO REDUCE THE RISK OF FIRE OR ELECTRIC RISK OF ELECTRIC SHOCK DO NOT OPEN SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the CAUTION:... -
Page 13: Fcc & Ic Information
20. Do not attempt to clean this unit 22. When moving the apparatus, be sure with chemical solvents as this might to first disconnect the power cord. damage the finish. Use a clean 23. Use caution when wearing loose dry cloth. clothing or articles near the spinning 21. - Page 14 Notes...
- Page 15 Notes...
- Page 16 fluance.com...
Need help?
Do you have a question about the DB10 and is the answer not in the manual?
Questions and answers