1 Safety Precautions 1.1. General guidelines 1. IMPORTANT SAFETY NOTICE There are special components used in this equipment which are important for safety. These parts are marked by in the Schematic Diagrams, Circuit Board Layout, Exploded Views and Replacement Pmarts List. It is essential that these critical parts should be replaced with manufacturer’s specified parts to prevent X-RADIATION, shock, fire, or other hazards.
2 Warning 2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatic Sensitive (ES) Devices Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Elec- trostatic Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semi- conductor "chip"...
NOTE: This Lithium battery is a critical component. (Type No.: CR2025 Manufactured by Energy Company, Panasonic Corporation.) It must never be subjected to excessive heat or discharge. It must therefore only be fitted in requirement designed specifically for its use.
3 Service Navigation 3.1. Introduction This service manual contains technical information, which allow service personnel's to understand and service this model. Please place orders using the parts list and not the drawing reference numbers. If the circuit is changed or modified, the information will be followed by service manual to be controlled with original service manual. 3.2.
3.4. Caution for DivX Please will always pass the customer “Warning for Customers Who Use the DivX Video-on-Demand content.” with the product and get it when you unavoidably exchange FLASH-ROM or P.C.B. including FLASH-ROM (When the product is exchanged, it is the same.).
3.5. Static Electricity Protection Measures • The laser diode in the traverse unit (optical pick-up) may break down due to potential difference caused by static electricity of clothes or human body. So, be careful of electrostatic breakdown during repair of the traverse unit (optical pick-up). 3.6.
4 Specifications Pickup: Wave Length: 405nm/660nm/780nm (BD/DVD/ Laser power: CLASS 1M/CLASS 1M/ Power supply: DC12V(DC IN terminal) CLASS 1M (BD/DVD/CD) DC7.2V Regional Code: DVD: #2 (Exclusive battery terminal) BD: Region B Power consumption: Media: Play Mode: Approx. 22W (Unit only Playable disc: approx.18W) BD-Video:...
Page 11
MP3: Compression rate: 32kbps~320kbps Sampling rate: 44.1kHz, 48kHz AVCHD (H.264): AVCHD format V1.0 HDMI: 480p(525p) /576p(625p)/ 1080i(1125i) / 720p(750p) / 1080p(1125p) HDMI (x.v.Color High Bit rate Audio) (This unit supports “HDAVI Control 5” function.) Wireless LAN Adaptor: DC5V(USB powered) 500mA Power supply: Max 2500mW Power consumption:...
6 Service Mode Information necessary for service can be displayed. Service mode setting: 1. Turn the power off. 2. Press the [OPTION] + [PLAY] and [VOL DOWN] button simultaneously for five seconds. 3. It is displayed on LCD as [SERV]. : It is shown to have entered the service mode. ([PLEASE WAIT] is displayed previously according to the A/V mode.) 4.
Page 16
Item LCD display Key operation Mode name Description (Remote controller key) Drive Check Simple quality of BD drive Press [0] [3] in service mode. *If the date of the present or the trouble occurred time is incorrect, it may be not able to judge correctly. Drive Check Simple quality of BD drive Press [3] [8] in service mode.
Page 17
Item LCD display Key operation Mode name Description (Remote controller key) BD drive last error BD drive error code display. 1. Error Number is displayed for 5 Press [4] [2] in service mode. seconds. 2. Time when the error has occurred is display for 5 seconds.
Page 18
Item LCD display Key operation Mode name Description (Remote controller key) 6. Disc maker ID is displayed for 5 In case that the maker cannot be seconds. identified, display is blackout. 7. Factor of drive error (hexadeci- mal) occurring is left displayed.
Page 19
Item LCD display Key operation Mode name Description (Remote controller key) 8. When the last error doesn't exist . CEC (H) output check Check of the CEC terminal high output of Press [5] [5] in service mode. HDMI. CEC (L) output check Check of the CEC terminal low output of Press [5] [6] in service mode.
Page 20
Item LCD display Key operation Mode name Description (Remote controller key) Release Service Mode Release Service Mode and turns the Power Displayed in STOP (SS) mode. Press [POWER] button on the front Off. panel or Remote controller in ser- vice mode.
7 Troubleshooting Guide 7.1. Self-Diagnosis Functions Self-Diagnosis Function provides information for errors to service personnel by “Self-Diagnosis Display” when any error has occurred. U** and F** are stored in memory and held. You can check latest error code by transmitting [0] [1] of Remote Controller in Service Mode. In case of clear the self-diagnosis display, remove the battery pack and the AC adaptor from the main unit after the power of the main unit is turned off.
Page 22
Error Code Diagnosis contents Description LCD Display Hang-up Displayed when communication error has occurred between Main microprocessor and Timer microprocessor. "F99" is displayed utill the [Power] key is pressed. UNSUP- Unsupported disc error This error is displayed when the following are detected. "This disc is incompatible."...
9.3. Bottom cabinet Ass'y 1. Release the latches and remove hinge cover (B). 2. Remove the 2 screws. 3. Remove the 9 screws(A) and 1 screw(B). <Removing battery pack> Release the lock lever and remove the battery pack in the direction of the arrow.
5. Release LCD cable, pull out the P57002(FFC), and then remove the bottom cabinet. NOTE: When remove the LCD cable, pull out the LCD cable straight in the direction of the arrow. NOTE: While fixing the FFC, push the FFC by its retainer plate instead of pressing it directly which may cause the wire bent.
9.6. Operation P.C.B. 2. Remove the JACK HOLDER (A) and (B), and then remove the Main P.C.B. and USB P.C.B.. 1. Pull out the P57004(FFC), remove the 2 screws, and then remove operation P.C.B.. 9.7. Main P.C.B. 1. Remove the 6 screws(A) and 3 screws(B). 9.8.
Caution: 2. Release the latches, remove the stand hinge cover, and Please don't lose the spring. then remove the stand ass'y. During assembly, insert the protruding end of the spring into the hole of the disc cover. 9.9. Main Cabinet Ass'y 1.
2. Release the latches and remove monitor cover. 6. Remove the LCD friction hinge and hinge cover(A), and NOTE: then remove LCD panel. Please don't lose 2 pieces of magnet plate. 3. Release LCD cable, pull out the P6001(FFC). NOTE: Please don't touch the magnet when installing FFC.
10 Measurements and Adjustments 10.1. Service Positions Note: For description of the disassembling procedure, see the section 9. 10.1.1. Checking and Repairing of Main P.C.B. (1)
Page 34
10.1.2. Checking and Repairing of Main P.C.B. (2)
Page 35
10.1.3. Servo Adjustment when exchange the Traverse or Main P.C.B. Refer to “9. Disassembly and Assembly Instructions” for details of disassembly and assembly. 10.3. Adjustment Instruction when Exchange the Traverse or Main P.C.B. (Servo Adjustment) 1. Connect the serial cable (RFKZ0139) to the main P.C.B. (P51601).
The Panasonic RAM disc should be recognized. Perform playback for one minute using the RAM disc. No abnormality should be seen in the picture, sound or operation. *Panasonic DVD-RAM disc should be used when recording and playback. Perform playback for one minute using the BD-Video disc.
10.3. Adjustment Instruction when [Upgrade procedure of firmware by disk making] • Step 1. Exchange the Traverse or Main Choose the model that you are using and download the firm- ware. P.C.B. (Servo Adjustment) • Step 2. (Preparation) Please defrost the downloaded file. 1.
Page 38
4. Select “Utility”. 9. Select “Exit”. 5. Select “COM Setup”. 10. Select “Adjustment”. 11. Insert the SD DIAG Card. 6. Select “COM1”, and select “OK”. 12. Turn on the switch of serial cable (RFKZ0139), and select “OK”. 13. Connect the AC power supply code with the power supply outlet, and select “OK”.
Page 39
15. Input the number of fifteen digits of QR code label (label 21. Set the DVD-RAM test disc (X5RAM-BPS), and select of the lower) pasted to OPU assay of the traverse unit, “OK”. and select "OK". 16. Take out the SD DIAG Card. 17.
Page 40
25. Take out the BD-ROM test disc (VFF0396), and select “OK”. 26. Detach the AC power supply code from the power supply outlet, and select “OK”. 27. Finish the servo adjustment. Select “Exit” and finish. 28. Detach the serial cable (RFKZ0139), and assemble the main body, and then confirm the sound with CD-ROM test disc (RFKZ0516).
R6101 2.2K 3.3K 1.5K VOL UP VOL DOWN TL6102 TL6101 S6105 K0C115A00002 RIGHT (B) ENTER (P) UP (A) DOWN (C) LEFT (D) DMP-B500EB DMP-B500EG USB SCHEMATIC DIAGRAM TL6104 TL6103 R6105 IR6201 R6107 R6106 R6104 PNA4811M00YD 4.7K 3.3K 2.2K 1.5K RETURN...
14 Appendix for Schematic Diagram 14.1. Voltage and Waveform Chart NOTE: Circuit voltage and waveform described herein shall be regarded as reference information when probing defect point, because it may differ from an actual measuring value due to difference of Measuring instrument and its measuring condition and product itself.
Page 51
IC56001 IC55901 Ref No. MODE PLAY STOP IC56036 Ref No. MODE PLAY STOP IC56036 Ref No. MODE PLAY STOP IC56036 Ref No. MODE PLAY STOP IC56036 Ref No. MODE PLAY STOP IC56036 Ref No. MODE PLAY STOP IC56036 Ref No. MODE PLAY STOP...
Page 52
IC8803 Ref No. MODE PLAY STOP IC8803 Ref No. MODE PLAY STOP IC8803 Ref No. MODE PLAY STOP IC8803 Ref No. MODE PLAY STOP Ref No. IC8803 MODE PLAY STOP IC8803 Ref No. MODE PLAY STOP IC8803 IC8804 Ref No. MODE PLAY STOP...
Page 55
15.1.3. Mechanical Replacement Parts List Safety Ref. Part No. Part Name & Pcs Remarks Description Notes: VEP76227A ETHER P.C.B. (RTL) E.S.D. *Important safety notice: RFKGBV200S MONITOR CABINET Components identified by mark have special character- ASS'Y L5EDD2Q00014 LCD PANEL istics important for safety. RKC0047 LCD FRICTION HINGE RGQ0577-S...
Page 56
Safety Ref. Part No. Part Name & Pcs Remarks Description RSC0936 HEAT RADIATION PLATE C RMQ1738 COPPER SHEET RMN0942-1 JACK HOLDER A RMN0943 JACK HOLDER B RGU2687B-W MAIN BUTTON RGU2688-W CURSOR BUTTON RGU2696-S POWER BUTTON REZ1986 MAIN-SW FFC REZ1987 MAIN-REMOCON FFC RKA0225-Q1 FOOT RUBBER VXA8770...
15.2. Electrical Replacement Parts List Notes: Safety Ref. Part No. Part Name & Pcs Remarks *Important safety notice: Description VEP76214A OPERATION P.C.B. (RTL) Components identified by mark have special character- E.S.D. istics important for safety. Furthermore, special parts which have purposes of P6101 K1MN06AA0046 CONNECTOR(6P) fire-retardant (resistors), high-quality sound (capacitors),...