Intelimax MA-2020 User Manual
  1. Manuals
  2. Brands
  3. Intelimax Manuals
  4. Modem
  5. MA-2020
  6. User manual

Intelimax MA-2020 User Manual

M2m 3g serial modem
Hide thumbs
Table of Contents

Advertisement

Quick Links

Intelimax+ User Manual
- 1 -

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MA-2020 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Intelimax MA-2020

Summary of Contents for Intelimax MA-2020

  • Page 1 Intelimax+ User Manual - 1 -...

  • Page 2: Table Of Contents

    Power Source ................- 13 - Operating Systems ............... - 13 - Intelimax+ Setup ................. - 14 - Connecting to the Intelimax+ ............- 15 - TCP/IP Connection - Recommended ..........- 15 - Serial Port Connection ..............- 16 - Modem Status Tab ................
  • Page 3 Telnet / SSH Commands ............... - 60 - Connecting to the modem via telnet ..........- 60 - Extended / Intelimax+ Specific AT Command Set (IP Stack Modes) ..- 75 - Device Information ............... - 75 - AT Command Password Protection ..........- 75 - WAN Extension Functions ..............
  • Page 4 Intelimax+ User Manual System ..................- 79 - maXconnect ................. - 80 - Serial (UART) port ................ - 80 - Engine Band ................- 81 - Check IP address of the WAN side ..........- 82 - ..................- 83 - Signal Strength ................

  • Page 5: Contact Information

    Intelimax+ User Manual C O N T A C T I N F O R M A T I O N In keeping with Maxon Australia’s dedicated Customer support policy, we encourage you to contact us. TECHNICAL: Hours of Operation: Monday to Friday 8.30am to 5.30pm*...

  • Page 6: Caution

    Intelimax+ User Manual R F E X P O S U R E A N D E L E C T R I C A L S A F E T Y C O M P L I A N C E The use of this device in any other type of host configuration may not comply with the RF exposure requirements and should be avoided.

  • Page 7: General Safety

    Intelimax+ User Manual General Safety RF Interference Issues: Avoid possible radio frequency (RF) interference by carefully following safety guidelines below: Switch OFF the Modem when in an aircraft. The use of cellular telephones in  aircraft is illegal. It may endanger the operation of the aircraft and/or disrupt the cellular network.

  • Page 8: Vehicle Safety

    Intelimax+ User Manual strike hazard. Vehicle Safety Do not use the modem while driving.  Respect national regulations on the use of cellular devices in vehicles. Road  safety always comes first. If incorrectly installed in a vehicle, the operation of the modem could interfere ...
  • Page 9 Intelimax+ User Manual metallic structures e.g. lifts. Any other area where you would normally be advised to turn off your engine  - 9 -...

  • Page 10: Revision History

    Intelimax+ User Manual R E V I S I O N H I S T O R Y Product Intelimax+ M2M 3G Serial Modem Model MA-2020 Document Type Current Version Number 1.03 Status of the Document Initial Release Revision Date...

  • Page 11: Intelimax+ User Manual

    Intelimax+ User Manual I n t e l i m a x + U S E R M A N U A L All data and information contained in or disclosed by this document are confidential and proprietary information of Maxon Australia, and all rights therein are expressly reserved.

  • Page 12: Introduction

    Intelimax+ User Manual I N T R O D U C T I O N Overview Breaking the industry benchmark, the top-of-the range Intelimax+ is a unique and intelligent fusion of 3G capabilities with advanced functionality of a modem/router. Intelimax+ Features General Features HSPA Wireless Module EHS6 (7.2Mbps downlink, 5.6Mbps uplink)

  • Page 13: Data Speeds

    Intelimax+ User Manual GSM/GPRS/EDGE 850MHz, 900MHz, 1800MHz and 1900MHz  Data Speeds HSPA: UL 5.76 Mbps /DL 7.2 Mbps  WCDMA PS: UL 384 Kbps / DL 384 Kbps  WCDMA CS: UL 64 Kbps / DL 64 Kbps ...

  • Page 14: Intelimax+ Setup

    I n t e l i m a x + S e t u p Maxon Intelimax+ serial modem supports a Winodws GUI, where by you can configure t he modem via serial connection or remotely via the WAN IP.

  • Page 15: Connecting To The Intelimax

    3. Set a static IP address to the modem: Once the drivers are installed you will have to set a static IP on the Intelimax+ network connection (as the Intelimax+ does not support DHCP) 4. The default IP for the Intelimax+ is 192.168.10.1, set your IP within this range Eg.192.168.10.50...

  • Page 16: Serial Port Connection

    Flow control: None Make sure to select the correct COM port and click the open button, the Intelimax+ GUI will connect to the modem via the selected COM port. The GUI can also perform a search for the correct baud rate if it is not known.

  • Page 17: Modem Status Tab

    Length of time since modem last rebooted (soft or hard) System time: Recovered from the internal cellular module (or NTP server if SNTP time client is enabled) IMEI: IMEI number of the Intelimax+ Version: Firmware version output. Includes version and compile date. Ex 0.0.0 [201401061408] H/W Version: Product’s board release version...
  • Page 18 Also shows the average, max and min over the last 15 minutes (time can be modified on admin page) Mode: IP Stack Mode of Intelimax+. (IP Stack Auto or Manual) Sent and received packets: Shows the packet count and number of bytes sent and received.

  • Page 19: Wan Configuration Tab

    Please select the correct operation mode as this will decide if the modem will automatically connect to the network on power up or work in pass through mode. The Intelimax supports 6 operation modes: 1. IP Stack Auto mode 2.
  • Page 20 Intelimax+ IPStack can be configured as a Server or Client mode. In Server mode the Intelimax+ will act as a socket server. The modem will listen on a specific TCP/UDP port waiting for an incoming client socket connection. As soon as the client drops the socket connection, the Intelimax+ will go back to socket listening mode as per IP stack configuration.
  • Page 21 This mode allows for the serial interface to connect through to the 3G module in the modem. In this mode the Intelimax+ processor still has some control and processing abilities over the serial AT commands and connection processes. Used for PPP pass- through or Circuit Switched Data (CSD).
  • Page 22 Can return to call if still active PPP Server Options The Intelimax+ can be configured to act as a PPP Server over the serial interface with an independent PPP WAN connection. There are three different PPP modes the modem can operate in, these are all outlined further in the PPP Server section: 1.
  • Page 23 Intelimax+ User Manual Band Change When band changing two reboots are required. The first reboot will save the setting to the module and second reboot will apply the changes to the module so that module will register to the selected band.

  • Page 24: Scheduler Tab

    Intelimax+ User Manual Scheduler TAB The scheduler tab allows configuring modem WAN connection schedule. The scheduler supports two methods of selection. Days of the Week (setup to come on certain days of the week) or Setting up a certain power up duration (setup to come certain during the hour).
  • Page 25 Intelimax+ User Manual To setup Scheduler by Day of the week, select the Day with connect and disconnect times. You can also set the modem to power off itself when it disconnects, by checking the power off check box. To delete an entry click on the entry and press the Remove selected Item button, or if you want to remove all entered entries click the “Remove...

  • Page 26: Serial Configuration Tab

    Intelimax+ User Manual Serial Configuration TAB The Serial configuration page is used to setup modem serial settings such as baud rate, serial messages, and SMS on boot. Serial Port Setup: Serial port setup includes the following Baud rate (the modem supports 1200, 2400, 4800, 9600, 19200, 38400, 57600 and...
  • Page 27 Serial port speed setup should be set to match host (connected via serial port) configuration. With certain applications there may be a need to fabricate a custom serial cable to work between the host and the Intelimax+. The custom serial cable depends on the equipment requirements and settings.

  • Page 28: Ip Stack Configuration Tab

    IP Stack supports TCP and UDP, depending on your application requirement you can choose between TCP and UDP communication SSLv3: If the SSLv3 check box is ticked, the Intelimax TCP/IP to serial converter applies SSLv3 encryption to the transferred data. SSLv3 encryption will applies to both client and - 28 -...
  • Page 29 2. The path .txt file should only contain the text “extra”. 3. Zip this folder, then upload to the Intelimax using the ‘Partial upload’ button in the GUI. Note: If both SSLv3 IP Stack and secure syslog is used at the same time then the same private key and certificate are used together (the ca.pem certification file is not used...
  • Page 30 PPP connection, reboot and start all over again. Primary Server Define the IP Address or DNS address of the primary server the Intelimax+ will try to connect to in Client mode, in server mode please leave this field as default.
  • Page 31 Intelimax+ User Manual specify Wake up time in seconds. Wake up feature will send dummy UDP packets prior to sending any data received via serial port to setup a channel with the network. The modem will send dummy packet twice as per timing set, followed by the actual data. This is to ensure the UDP data is not lost.

  • Page 32: Modem Emulation Tab

    ATDT command via serial and will drop the connection when the call is hung up (+++, ATH). If the Intelimax+ is in IP stack auto mode (server) then it will act as an IP stack server (and therefore could be addressed remotely) until it receives the dial out commands.
  • Page 33 Intelimax+ User Manual RING Message To emulate the incoming CSD call the Intelimax will print out RING messages at a rate of 1 RING per second according the S0 setting. In order to account for this delay when dialing out through the modem it is advisable to add a CONNECT message delay using the AT$$TCPDEL=<MS>...

  • Page 34: Dynamic Dns

    Intelimax+ User Manual Dynamic DNS Allows the user to configure; Username, Password and Domain name to be used by Intelimax+ when authenticating on a DDNS server.  Enable DDNS  Select to enable DDNS.  Service Provider  Link of the DDNS service web page (Server site is http://dyn.com) by default) ...

  • Page 35: Ppp Server

    Serial 3G connection In this working mode, the Intelimax will launch a PPP server and wait for the user device PPP client to connect. Once the PPP connection is established, the device can talk to the Intelimax through a network connection. The Intelimax then acts like a network gateway, all data traffic from the device will be routed to the WAN interface, and then be sent to the internet.
  • Page 36 Only pre-defined AT commands are supported. Please refer to the Maxon Intelimax user manual for the custom AT command format and which commands are currently supported. There are several commands that are not needed when the Intelimax is in PPP server - 36 -...
  • Page 37 ATD or ATDT AT$$IPCTOS AT$$IPCTCS AT$$TCPDEL All socket related commands are not supported because when the Intelimax works in PPP server mode, the TCP/UDP socket on the WAN side is no longer needed, the modem now is a gateway. PPP Dialing Modes Three Dial modes are supported: ...
  • Page 38 PPP connection, it requires the exchange of the text strings “CLIENT” (from the client) and “CLIENTSERVER” (from the serer). So in MS Chat mode, the Intelimax PPP server will expect a “CLIENT” string from the client and then send back “CLIENTSERVER”.
  • Page 39 All standard AT commands and Maxon customized AT$$ commands are supported. The command ATDT*99***1# is to notify the Intelimax to go into the PPP mode, after this command no more AT commands are supported through direct accessing of the serial port.
  • Page 40 Intelimax+ User Manual MRU: Maximum Receive Unit. The PPP server will ask the client to send packets of no more than [MRU] bytes. The value must be between 128 and 16384; the default is 1500. Idle Timeout: This is to specify that PPP server should disconnect if the PPP link is idle (No data traffic) for [Idle] seconds.

  • Page 41: Administration Tab

    Intelimax+ User Manual Administration TAB Telnet and SSH login  User Name setting using for Telnet and TCP connection.  Password setting using for Telnet and TCP connection.  Enable or disable Telnet.  Set Telnet port number to use.
  • Page 42 2. The path .txt file should only contain the text “extra”. 3. Zip this folder, then upload to the Intelimax using the ‘Partial upload’ button in the GUI. 4. Enable ‘Remote syslog’. If the Intelimax+ detects that remote syslog is enabled and has the valid certification files, then it will change from UDP unsecure syslog to TCP secure syslog with TLS encryption to port 504.

  • Page 43: Rssi Logging

    Intelimax+ User Manual RSSI logging  Configure the time period over which the RSSI logging will be averaged (between 5 and 60 minutes). The RSSI value is measured every 10 seconds.  Configure the level at which the RSSI signal strength will be considered high. This is the level at which the PWR LED will flash solidly.

  • Page 44: System Tab

    System TAB AT over IP AT over IP can be used to access the AT command interface of the Intelimax+ internal cellular module or the Intelimax specific modem AT commands. The AT over IP function can be used either over the local USB/LAN interface to the modem or via a remote IP connection.

  • Page 45: Debug

    It is not necessarily limited to TCP/IP networks. The Intelimax+ supports SNMPv2 and SNMPv3, if the ‘V3’ check box is ticked SNMPv3 is used otherwise SNMPv2 is used. Secure SNMPv3 SHA authentication and AES privacy is supported.
  • Page 46 Intelimax+ User Manual IMPORTS OBJECT-TYPE, MODULE-IDENTITY, Integer32, enterprises FROM SNMPv2-SMI DisplayString FROM SNMPv2-TC; MaxMIB MODULE-IDENTITY LAST-UPDATED "201104150000Z" ORGANIZATION "DHPLAB" CONTACT-INFO "support@maxon.com.au" DESCRIPTION "Maxon MIB" REVISION "201104150000Z" DESCRIPTION "This file defines the maxon mib by dhplab." ::= { enterprises 0910 } signalStrength OBJECT-TYPE SYNTAX Integer32 (0..105)
  • Page 47 Intelimax+ User Manual rscp OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "RSCP of the modem" ::= { MaxMIB 4} imei OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "IMEI of the modem" ::= { MaxMIB 5} boardreset OBJECT-TYPE SYNTAX Integer32 (0..1)

  • Page 48: Sntp

    SNMPv2 or SNMPv3. SNTP SNTP can be used to update the time of the Intelimax+. The modem will by default take its time from the network. When SNTP is enabled, the modem will query a network- based NTP server using the SNTP protocol and pull the time from it. The timezone can be configured depending on where in the world the modem is used.

  • Page 49: Other Gui Functions

    Intelimax+ User Manual Other GUI functions Output Info  Output Information for receiving Intelimax+’s data in serial or remote access.  When syslog are requested, this is where they are printed before being saved to a file. Clear Output Clear all information in the ‘Output Info’ window.

  • Page 50: System Functions

    Intelimax+ User Manual System Functions Save Config to file Save modem configuration as an encrypted .dat file. Load Config from file Load modem .dat configuration file. Save syslog If remote syslog is not enabled, this will print out the internal system logs to the ‘Output Info’...
  • Page 51 Intelimax+ User Manual Factory Resets the Intelimax+ to firmware factory settings. This will wipe all the settings on the modem, including the configured saved profile settings. This can also be achieved by holding down the modem reset button for between 20 and 60 seconds.

  • Page 52: Firmware Upgrade

    Click ‘Firmware Upgrade’ button and select firmware file. And open the file, the uploading process will begin after a short delay. Do not remove Intelimax+’s cable or turn off the power until upgrade finishing. The modem will reboot and come back online once the firmware upgrade process has completed.

  • Page 53: Sms Commands (Ip Modes)

    Intelimax+ User Manual SMS Commands (IP modes) The Intelimax can be used to send and receive SMS messages through standard SMS AT commands with an internal buffer of 100 messages. In addition to this the Intelimax supports a number of custom SMS messages for which can be used to check and modify some settings remotely.

  • Page 54: Sms Commands (Serial Modem Modes)

    Intelimax+ User Manual SMS Commands (Serial modem modes) The Reboot Intelimax+ SMS command can be used to act on Intelimax+ specific SMS messages when in serial modem mode. For this to happen the modem must be told to intercept the SMS messages using the AT$$STEALTHSMS command.

  • Page 55: Remote Change From Csd Mode To Ip Mode

    Dial out to the modem via a command line terminal session to your data modem using the data number of the SIM card in the Intelimax+. The sting will be as follows: ATDT0400123456. Once the ‘CONNECT’ message has been displayed you are connected.
  • Page 56 Once the modem reboots (approximately 2 minutes) if a public dynamic IP address has been used it can be found using the following SMS to the phone number (not data number) of the SIM in the modem: INTELIMAX.PARK.WANIP - 56 -...

  • Page 57: Led Functionality

    Data Transfer Indication In addition to the below LED flashing sequence the Intelimax+ will also display TX and RX activity on the LEDs. When data is received on the serial port and sent over the WAN the green LED in the PWR/RSSI side will flash.
  • Page 58 Intelimax+ User Manual Serial Modem mode Description Signal Strength Power LED Data LED SERIAL MODE IDLE SIGNAL > -84dBm (or excellent RSSI setting) SERIAL MODE IDLE ≤ -84dBm > -89dBm 200ms OFF 800ms ON SERIAL MODE IDLE ≤ -89dBm > -96dBm...

  • Page 59: Device Operation Checking / Debugging

    Local and remote checking: The Intelimax GUI allows for the user to check the status of the modem both locally and remotely via an IP connection as well as recover, signal strength and system logs for diagnosis. The GUI status page indicates the signal strength, both current, and average, max and min over the configured period, the current connection status, IP address, registration, area information etc.

  • Page 60: Telnet / Ssh Commands

    Telnet / S S H C o m m a n d s Using Intelimax+ Telnet / SSH commands allows you to configure the modem remotely, also you can send diagnostic commands here is summary off of tasks that you can perform 1.
  • Page 61 Intelimax+ User Manual Once you login to telnet. You can choose whether to start telnet service, set up configuration, Configure via AT command, use ping function, show uptime reboot and reset the modem remotely to factory default using option provided i.e stat, setup, at, ping, uptime, reboot and defconfig respectively.
  • Page 62  Status of INTELIMAX+ Shows the syslog information if it is not set as remote syslog Sysinfo Shows F/W version and system Time and IP Address of Intelimax+ Display Primary DNS and secondary DNS address of Intelimax+ - 62 -...
  • Page 63 Syslog and can enter up to three phone number for SMS 2.DDNS Users can configure Dynamic DNS using this command 3.MODE Intelimax+ support IP stack and Serial mode only, using this option(Mode) users can configure WAN scheduler, UART/Serial port setting and IP stack setting 4.SNMP Users can enable/disable this feature that allows network monitoring 5.SNTP...
  • Page 64 Intelimax+ User Manual SYSTEM DDNS - 64 -...
  • Page 65 Intelimax+ User Manual - 65 -...
  • Page 66 Intelimax+ User Manual MODE 1.WAN This command will allow users to select operating mode, configure users name password, enter APN, Enable/Disable Auto PIN function, enter PIN code and configure WAN scheduler. 2.WAN Scheduler This command will allow users to control WAN connection in a specified time.
  • Page 67 Intelimax+ User Manual WAN Scheduler - 67 -...
  • Page 68 Intelimax+ User Manual UART/Serial Port IPSTACK - 68 -...
  • Page 69 Intelimax+ User Manual SNMP General - 69 -...
  • Page 70 Intelimax+ User Manual Trap SNTP - 70 -...
  • Page 71 Intelimax+ User Manual AT command direct to Module Signal Strength Check To check signal strength use “at at+csq?” command. Refer to the screen shot below: - 71 -...
  • Page 72 Intelimax+ User Manual PING command System uptime check. - 72 -...
  • Page 73 Intelimax+ User Manual The command uptime shows you the connection time as shown in the screen shot below. Set to Factory Use defconfig to clear all the setting which will configure the modem to factory default state. - 73 -...
  • Page 74 Intelimax+ User Manual Reset the INTELIMAX+ Intelimax+ can be power rebooted using the reboot command after logging into the Intelimax+ remotely - 74 -...

  • Page 75: Extended / Intelimax+ Specific At Command Set (Ip Stack Modes)

    C o m m a n d S e t ( I P S t a c k M o d e s ) Device Information Manufacturer: Maxon Australia Pty Ltd Model Number: MA-2020 Product Name: Intelimax+ F/W Revision: 0.0.0 [201201130929] H/W Version: 1.0...

  • Page 76: Wan Extension Functions

    Intelimax+ User Manual To disable the password protection for a session enter the following, this will persist until the modem reboots: AT$$PWD=<PWD> WAN Extension Functions AT$$WANSE? $$WANSE: PINGCHECK:Enable,0,0,0.0.0.0, BACKOFF:Disable,0,0,0,0 Parameters $$WANSE: X,X,X,X,X,X 0,1 PINGCHECK,BACKOFF 0,1 Disable/Enable both expansion PINGCHECK and BACKOFF...

  • Page 77: Periodic Reset

    0,1 Disable/Enable Reset (TCP Connected State) – Client – If enabled will wait until Intelimax+ client drops connection to a server or server drops connection 0,1 Disable/Enable Reset (At scheduled Time) HH:MM for Reset (At scheduled Time, 24 hour format) Battery (12.3 volts ON, 11.9 volts OFF)

  • Page 78: Ip Stack Setting

    Intelimax+ User Manual 0~28 Entry number of day of week [Delete]/0,1, 2,3,4,5,6 Day of week[Ddd]/5~59 Minutes of power cycle 0~23 Hours of start 0~59 Minutes of start 0~23 Hours of finish 0~59 Minutes of finish 0,1 Engine power down IP Stack setting AT$$WANSI? $$WANSI: 1,1,1,0,0.0.0.0,0.0.0.0,30000,1,300,20,0,0...

  • Page 79: Ddns

    Intelimax+ User Manual 01,192.168.0.202 Parameters $$SNMPS: X,X,X,X,X,X,X,X,X 0,1 Disable/Enable Read community Write community Name Contact Location Trap 1 IP address Trap 2 IP address Trap 3 IP address DDNS AT$$DDNSS? $$DDNSS: Disable,,, Parameters $$DDNSS: X,X,X,X 0,1 Disable/Enable DomainName UserName Password...

  • Page 80: Maxconnect

    Phone number of Administrator Phone number of Administrator Phone number of Administrator maXconnect To enable maXconnect on the Intelimax+ either use the GUI or enter the following commands when the modem is in IP Stack Auto mode. $$MAXCNT: 0,120,portal.maxconnect.com.au,1883,updates.maxconnect.com.au AT$$MAXCNT=?

  • Page 81: Engine Band

    Intelimax+ User Manual this command, but other commands can also be set using standard AT commands such as AT+IPR, AT+IFC etc. AT$$SPORT? $$SPORT: 115200,8,N,1,None Parameters $$SPORT: X,X,X,X,X 2400,4800,9600,19200,38400,57600,115200 Baud rate 7,8 Data bits N,E,O None/Even/Odd 1,2 Stop bits None, Software, Hardware Flow control...

  • Page 82: Check Ip Address Of The Wan Side

    Intelimax+ User Manual Examples: / GSM 850/900/1800/1900 AT$$BAND=3f $$BAND: 0000003f The AT commands on the module can be set and checked directly using AT$$DIRAT. AT$$DIRAT="at^syscfg=2,2,380380,1,2" – make sure module band is set AT&W AT$$RESET // WCDMA 850 AT$$BAND=400 AT$$DIRAT="AT^SYSCFG=2,2,4000000,1,2" AT&W...

  • Page 83: Ftp

    Intelimax+ User Manual To use FTP on the Intelimax+ allow for append on the FTP server. Also restrict the welcome message to less than 10 characters. Please save and apply settings before using. AT$$FTPCS? AT$$FTPCS: 1,192.168.10.1:21,maxon,maxon,0,INTELIMAX+,1000,1 Parameters $$FTPCS: X,X,X,X,X,X,X,X 0 - Disable...
  • Page 84 Intelimax+ User Manual AT$$FTPCS=5, 20.19.62.23:21,maxon,maxon,30,FILEHEADER,10000,0 AT command to upload every day at 8PM. AT$$FTPCS=3, 20.19.62.23:21,maxon,maxon,20,FILEHEADER,10000,0 AT command to upload every 15 day of the month. AT$$FTPCS=4, 20.19.62.23:21,maxon,maxon,15,FILEHEADER,10000,0 1. In the example above file size is 10000 bytes. 2. The modem would create a text file using name specified above (in the example I have used “fileheader”...

  • Page 85: Signal Strength

    Will start the FTP connection and upload the files. Can be used to force an upload when in periodic mode. If no WAN connection is currently established (such as in IP Stack Manual mode) the Intelimax+ will establish the PPP and socket connections, upload the FTP files then drop the socket and PPP connections.

  • Page 86: Open Ppp Connection

    Intelimax+ User Manual Open PPP connection AT$$IPCTOP Close PPP connection AT$$IPCTCP Open TCP/UDP Socket AT$$IPCTOS Close TCP/UDP Socket AT$$IPCTCS Change Remote Server IP address AT$$IPCTRIP=0,ip,ad,dr,ess,<port> Eg. AT$$IPCTRIP=0,123,456,789,01,30000 Change client/server mode AT$$IPCFL=4,<0,1> where 0 for server, 1 for client Eg. AT$$IPCFL=4,0 sets modem to server mode...

  • Page 87: Change Modem Mode

    Intelimax+ User Manual AT$$IPSCFG? $$IPSCFG: 30,100,200,301 Change modem mode AT$$CHGMODE= 1 – IP Stack Auto 2 – IP Stack Manual 3 – Serial Modem at$$chgmode=1 Save and Reboot AT$$RESET At$$reset Factory Reset AT$$FACTORY Profile Save AT$$PFSET Save the modem’s profile default settings...

  • Page 88: Modem Emulation

    Require Save and System Reboot at$$overip? $$OVERIP: 1,12522 Modem Emulation The Intelimax+ modem emulation can be configured using the following AT commands: To enable modem emulation and add a data number to IP address and port number emulation to the list at$$emul=1,phone_number,IP_address,port_number e.g.

  • Page 89: Modmax Compatibility Mode

    Intelimax+ User Manual To Enable/Disable Modem Emulation – this must be enabled on the server Intelimax+ for CONNECT message at$$emul=0,0 – disable at$$emul=0,1 - enable To delete a rule from the list at$$emul=2,list_number e.g. at$$emul=2,1 at$$emul? $$EMUL: 1,2 0,01044204412,192.168.101.2,3000 1,01044204414,211.232.22.1,500001 It is recommended to add a TCP delay to the client connect message to account for the incoming RING messages on the server side.
  • Page 90 Intelimax+ User Manual messages, this delay allows for these legacy systems to handle this delay. AT$$TCPDEL=? $$TCPDEL: X Delay between try and connect range from 200 to 1000 mili seconds. AT$$TCPDEL=200 AT$$TCPDEL? $$TCPDEL: 200 - 90 -...

  • Page 91: Prepare Modem For Hard Shutdown

    AT command allows for the processor to perform housekeeping duties to ensure that the shutdown process does not damage the modem or internal cellular module. AT$$RTD SMS on Boot The Intelimax+ can be configured to send an SMS at boot time using the following AT commands: at$$pwronsms=? $$PWRONSMS=1,0/1 enable/disable...

  • Page 92: Extended / Module Specific At Command Set (Ip And Serial Modes)

    Intelimax+ User Manual E x t e n d e d / M o d u l e S p e c i f i c A T C o m m a n d S e t ( I P a n d S e r i a l M o d e s ) Save settings and reset/restart modem AT&W –...

  • Page 93: Single At Command Sms At+Mmc Smsmo

    AT command allows for the processor to perform housekeeping duties to ensure that the shutdown process does not damage the modem or internal cellular module. AT$$RTD SMS on Boot The Intelimax+ can be configured to send an SMS at boot time using the following AT commands: at$$pwronsms=? $$PWRONSMS=1,0/1 enable/disable...

  • Page 94: Csd And Psd/Ppp Dial Out Commands (Serial Mode Only)

    Intelimax+ User Manual CSD and PSD/PPP dial out commands (Serial mode only) Command  Command  ATD<phone_number> CONNECT (Data call connected) Notify Connect <Speed> if connect_baud is set.  NO CARRIER (Data call failure) phone_number: for Packet Switched Data: *99# (Australia – requires authentication)

Table of Contents