It enables users to view via IE browser, centre management software client software; AJ series products are applicable for big, medium-sized and small enterprises, chain store, factory, home and all kinds of spots where remote network video transmission and control supposed to be installed, They are easy to install and operate. Before the...
Page 3
IPCAM User Manual 3.2. Logging and Active X Installation..............13 3.3. Main Operation Interface.................14 3.4. Operator Operation ..................15 3.4.1. Multi-Device Settings.................15 3.4.2. Basic Network Settings................17 3.4.3. Wireless Settings..................18 3.4.4. ADSL Settings....................18 3.4.5. DDNS Settings.....................19 3.4.6. E-mail and FTP Services Settings..............19 3.4.7.
IP cameras are able to extend to both analog and digital signal. The core of AJ series IP cameras is 32Bit RSIC, adopts standard MJPEG compression format, camera sensor is CMOS, support auto white balance and backlight balance, support IE, cell phone browser,centralized monitor interface...
IPCAM User Manual 1.1. Product Specifications *- Adopt high Performance, strong function media processor 32Bit RSIC *- High sensor CMOS *-Adopt optimized MJPEG video compression algorithm, realize high-definition images transmission in narrow bandwidth; *-Maximum support 15 users viewing at the same time, no limit for users if using Forwarder Server function;...
DirectX8.0 or above version TCP/IP network protocol 2. Interface & Installation There are two kinds of AJ series IP camera interfaces: one is body guard interface, the other is the extend line interface, set two representative products as examples, to give explanation:...
IPCAM User Manual Power Supply Light: constant on after power up Network light: constant sparkle after power up data transmission. Ethernet interface: RJ-45 interface. I/O interface: 1 router alarm input, accept 3, 4 two terminals (input terminal grounding, low level effective trigger); 1 router TTL control input, connect 1,2 two terminals (1,2 terminals short connections).
IPCAM User Manual This is the most popular network access way, as long as there is a router, internet cable connect router directly to IP Camera, IP Camera can connect to Internet as normal PC, as shows: 2.2.2. PPPoE Installation Under the condition, users need set PPPoE dialing parameter on IP Camera: input the username and password ISP supplier’...
IPCAM User Manual connect to IP camera (note: don’t apply for wrong power), after one minute modification of IP camera, video could be connected by internet cable to IP camera; under the normal condition, yellow light is on, green light flickers, now physical connection of IP camera finish at this time (in order to connect successfully, we advise to set camera IP as the stable IP at the same net range of PC in LAN , how to set, please refer to 8 frequent questions answer).
Page 10
IPCAM User Manual Figure 3.2 If network cable and power supply are correctly connected, device type, name and IP address will be shown in the Equipments list (Otherwise, please confirm whether power supply and network cable work normally). In the interface above, the configuration information of the current computer is listed on the left side;...
IPCAM User Manual Note: Device information indicates the IP camera information. When the current computer has a fixed IP, (namely non-DHCP IP), and the IP camera is used for the first time, please click Update, so that IP address of the IP camera, gateway and DNS can be synchronous with the PC. If it is necessary to manually modify the contents including camera name, HTTP port, IP address, sub mask, gateway, primary DNS server, secondary DNS server and so on, please click apply after...
Page 12
IPCAM User Manual 2. If the IP camera has been connected with the outer network when you are browsing it, the log-in interface as below will appear when you open the web page through LAN or outer work. Figure3.3 When the item connects to outer networking, a log-in interface will appear. For example: Figure3.4 Figure3.4 enter log in information, click OK to enter, an installation pop-up will appear: e.g.
Page 13
IPCAM User Manual Figure3.5 Select the needed language, and the way you want to visit. Click Sign in. after installation Active X you can use it. If it is blocked and requires plug-in installation by antivirus software, please remove block Note:...
IPCAM User Manual 3.3. Main Operation Interface Figure3.6 For example: If the is a bright , indicating the device is the first way to monitor the status. When you log on the operator interface, you can perform PTZ and video parameters Direction control: Click the arrows in different directions can be the lens to the appropriate direction of rotation Vertical cruise...
IPCAM User Manual OSD: In the video display date and time. You can disable the OSD function or choose the color of OSD. Snapshot Photo: Click the icon interception photo. ,again, click Video: Click icon to enter the recording mode, the icon becomes the end of the recording.
Page 16
IPCAM User Manual password, click “Add.” Repeat this process you can continue to add devices. Finally do not forget to click on the “Settings” button. Figure3.7 Add a device on the internet First, make sure you want to add devices to access via IP address or domain name.
IPCAM User Manual Figure3.8 3.4.2 Basic Network Settings Figure3.9 This sector is for DHCP and IP configuration,port forwarding is needed, If you choose to set IP address,please fill in the relative IP address、subnet mask, gateway, DNS server, Http port;...
IPCAM User Manual 3.4.3 Wireless Setting First make sure that your wireless router is working well. Then click the button. After you click twice. The camera will find out the Wireless LAN automatically. Then select the Wireless LAN you wanted. Then the Wireless LAN’s information will showing.
IPCAM User Manual 3.4.5 Dynamic DNS Setting(DDNS) Figure3.12 All the above information is set up when the device is ready to deliver; users generally do not need to change. In case of any accidental loss, user needs to re-obtain the domain name, and fill it himself, juts do as the above, the user’s name is just the first four characters, and this is for remote access.
IPCAM User Manual The above setting is a preparation for the alarm function, the sender should be entered the sender’s email address,recipient 1、2、3、4 is filled with recipient E-mail address;SMTP server should be filled with the sender email SMTP server,e.g. the sender email address is abc@163.com,and enter mail.163.com.
IPCAM User Manual keeps consiste nt with the mentioned upload pictures interval of Ftp service settings. The schedule refers to arming time,as the selected time interval: 0:00 minute per week to 0:45 minutes and Monday 1:00 hour and 2:00 hour Figure3.15 3.4.8 Reset/Firm Ware Upgrade This sector is for camera firmware upgrade, it includes device system firmware...
IPCAM User Manual 3.4.10 Reboot Equipment Click restart, it appears the above picture, click ok, wait for 1 minute and you can use it normally Others 4.1 Port Forwarding Settings in router When a remote access via internet visit, port forwarding in router is a must, different brands routes have different name, but the operation is the same.
IPCAM User Manual address is 192.168.1.50, and port is 80. 1. First log in router web administration interface. 2. Click in front of left side “Advanced Setup Click “virtual server” in the unfolded menu. 4. fill “80” under the right port start or port end, Server IP address fill "192.168.1.50", protocol select "TCP/UDP"OR”“TCP”, finally don’t forget click under “"save/apply”...
Page 24
IPCAM User Manual warranty period will be free maintenance. Warranty Terms as following: a) Charge-free maintenance of the product is one year. We can repair it for free during the guarantee period (Damages not caused by misuse or vandalism). Repair over guarantee period, we will charge maintenance fee. b) During guarantee period, breakdown caused by misuse or other reasons out of range of warranty.
Need help?
Do you have a question about the AJ series and is the answer not in the manual?
Questions and answers