Related Manuals for eWON COSY 141
Summary of Contents for eWON COSY 141
-
Page 1: Installation Guide
Installation Guide IG 010 / Rev 1.3 eWON COSY 141 - Installation Guide This short guide explains how to install eWON COSY 141 and to get started with the embedded configuration web site. -
Page 2: Table Of Contents
3.1 Factory default IP settings ......................12 3.2 Selecting the appropriate LAN IP address ................. 12 3.3 Setting the eWON COSY Machine LAN IP address ..............13 3.4 eWON COSY's web interface ....................14 3.4.1 Accessing the eWON COSY ..................14 3.4.2 Going through the 1-2-3 Setup Wizard ................ -
Page 3: Foreword
Foreword 1. Foreword The present Installation Guide describes the hardware and software features of the eWON COSY. It does not address the 1-2-3 Setup procedure that is explained in 3 hands-on videos you can watch on eWON Website 2. Hardware description Housing interfaces Power supply (polarity sensitive, see label). -
Page 4: Markings
Chapter 2. Hardware description Markings The identification label of the eWON is placed at the left hand side of the housing. The different parts of the label are shown below: Device type and interfaces Serial number 1145 = year+week 0062 = sequential number... -
Page 5: Mechanical Outline
Chapter 2. Hardware description Mechanical outline The recommended free space in the cabinet for the eWON should be at least: 40-mm wide x 200-mm high x 160-mm deep (includes space for smooth cable bending). Latch for Omega-shape DIN rail to EN50022. -
Page 6: Mounting And Environmental Conditions
Hardware description Mounting and environmental conditions The eWON COSY unit has an IP30 protection grade. It is therefore not suited for outdoor mounting. The design of the unit is such that it has to be integrated in an enclosed electrical cabinet, protected from excessive heat humidity and dust. -
Page 7: Front Panel Status Leds
Flashing green = life (20 secs after power on) Internet access configuration (green = OK) VPN-tunnel status (green = OK, DO = 1) Ethernet ports By default, only the LAN Ethernet interface of the eWON COSY can be used to access the internal web site. 2.8.1 Machine LAN The Machine LAN interface consists of a four port autosense Ethernet switch (10/100 Mb). -
Page 8: Serial-Ports
RS232/422/485 (no galvanic isolation) Polarization 680 Ω (if polarization & termination is activated) Termination 120 Ω (if polarization & termination is activated) Pin # RS232 RS485 RS422 SUBD9 connector pinout eWON COSY 141 - Installation Guide (How to) Page 8/20... -
Page 9: Mpi Port
Chapter 2. Hardware description 2.9.2 MPI port The MPI version of the eWON COSY is easily identifiable with its light turquoise square surrounding the SUBD9 female DB9 connector. Characteristic Value Physical mode MPI (no galvanic isolation) Baud rates From 9,6 kBauds to 12,0 MBauds Polarization 100 kΩ... -
Page 10: Digital Input - Digital Output
2.10 Digital input – Digital output The eWON COSY features one Digital Input (DI) to enable/disable the Internet port from outside and one Digital Output (DO) that returns the status of the VPN tunnel connection. The DI and DO cannot be allocated to other functions. - Page 11 Chapter 2. Hardware description (*) when the eWON COSY reboots, a short phase of ON state is part of the starting process. The digital output is activated by an open drain MOSFET transistor driven by an optocoupler. The maximum current flow into this transistor has a characteristic above the value specified in the eWON, in order to cope with the switching power losses.
-
Page 12: Software Configuration
IP ranges of involved networks. Example of networks involved during the remote access : To allow routing to the devices connected to the eWON Machine LAN, following conditions must be complied: Network 1 <> Network 3: Company LAN address range must differ from eWON Machine LAN address range. -
Page 13: Setting The Ewon Cosy Machine Lan Ip Address
(ask the network administrator). Knowing the ranges in use at the Company and Site side, you must select for the eWON Cosy Machine LAN a range outside these networks. -
Page 14: Ewon Cosy's Web Interface
Connect your PC with one of the LAN ports, make sure your PC has an IP address in the same range as the one of the eWON COSY, open your Internet Browser and, in the URL address field, enter the actual LAN address you configured in the eWON COSY:... -
Page 15: Going Through The 1-2-3 Setup Wizard
3.4.2 Going through the 1-2-3 Setup Wizard After login, on a new eWON that was not yet configured the Quick Launch Wizard page opens: Button to access the Status page for each setup aspect (appears on all pages) Button allowing to return to this starting page (appears on all pages) -
Page 16: Status
Chapter 3. Software configuration After going through each the wizard, the info bar of the eWON COSY shows checked boxes for each aspect that has been configured. The present installation guide does not cover all setup aspects in details. Each step of the 1-2-3 Setup is documented by a hands-on video tutorial. Go to the eWON COSY support page http://support.ewon.biz/cosy.htm... - Page 17 The example below shows how the same Status page looks when the Internet connection locked by the digital input (switch open). To access the detailed Status page, click the button in the message box: Note: access to this page requires to be logged-in. eWON COSY 141 - Installation Guide (How to) Page 17/20...
-
Page 18: Troubleshooting
Note: you absolutely have to wait until the full auto test procedure is completed without interrupting it. If the auto test is interrupted, the flash memory of the eWON will contain random data likely to make it unstable. In such a case you have to redo the second level reset procedure from scratch and wait until it is totally completed. -
Page 19: General Characteristics Of Ewon Cosy
Chapter 4. Troubleshooting When performing a second level reset, the eWON does NOT restart in normal mode by itself and remains running in diagnose mode. Power the eWON OFF and ON again to restart in normal mode. As described before, the eWON returns to its default COM parameters and factory IP addresses after this level 2 reset is performed. -
Page 20: Revision History
No part of this handbook can be reproduced, transmitted or copied in any way without written consent from the manufacturer and/or the authors of this handbook eWON sa eWON COSY 141 - Installation Guide (How to) Page 20/20...
Need help?
Do you have a question about the COSY 141 and is the answer not in the manual?
Questions and answers