Installation And Use Of Pir Motion Detector; Chapter Nine Troubleshooting - KERUI G18 User Manual

4.The indicator lighting for 1 second means alarm. The indicator in constant light
is a suggestion of low power.
5.A, B can also be reinforced by screws, (A: remove the bottom cover, strengthen
the screw and then cover the bottom agian; B can be directly fixed by the screw.)

8.2 Installation and Use of PIR Motion Detector

Before use, make sure the power switch of PIR motion sensors is ON. Installation
height is about 2.2 meters above ground and it should be installed in the corner
of the room to get the best detection range. At the same time, it should form a
certain angle with the walking line ( 90 degree angle is best for detection).
Installation:
Talk out the supplied bracket, insert the bracket to the slot. Take out the pedestal
and fix it with two screws on the wall. Press the PIR with bracket into the center
hole of the pedestal. And then adjust the best angle of detector. (This method is
suitable for project installation)
Attention:
1.The detector should not face the outside of window directly.
2. There should be no any big objects for obstruction within coverage of detection, .
3. There should be no two infrared detectors in the same space as they will possibly
intervene with each other.
4.Avoid facing window, cooling or warming machine, stoves, or other appliances
that cause temperature changing sharply, which may cause false alarm.
5. Infrared detector should be used indoor only.

Chapter Nine Troubleshooting

Troubleshooting
Reasons
1.Not arming
2.alarm phone unset
1.No dialing for alarm
3.parts improperly installed,
distance too far
4.code not match
2. Can't remote
1.input wrong password
operate
1.No SIM card
2.PIN code is set for SIM card
3.bad GSM signal
3. Host can't read 4.SIM card has scratched
SIM card or don't
copper
dial and text to
5.Alarm phone number unset
preset alarm
6.Message Alarm number
phone number unset
7.Card balance is insuffic
ient or out of date
8.Message function is OFF
1.coding unmatched with
the host
4. remote controller 2.insufficient power
not work 3.batter y pieces poor
contact or corroded
4.unmatched with host
1.coding unmatched with
the host
5. remote controller 2.insufficient power
not work
3.batter y pieces poor
contact or corroded
4.unmatched with host
1.coding unmatched with
the host
2.insufficient power
6. PIR sensor not work
3.batter y pieces poor
contact or corroded
4.unmatched with host
1.a nearby emitter is sending
signal
7. The transmitter
2.The host receiver stops work
distance for host is
3.Power supply of standby
shortened
batter y of the host is
insufficient
Methods
1. do arming operation
2.re-set according to the
instruction book
3. adjust the location of parts
4. re-coding
1. Correct password or change
to a new password
1、Insert SIM card
2、Cancel PIN code
3、change to a strong signal place
4、change to a normal SIM card
5、set alarm phone number
6、set message alarm number
7、charge SIM card
8、activate the message function
1. re-coding
2. change batter y of the same type
3. eliminating the dirt on the
pieces caused by corrosion
4. contact the local dealer to
change the matched remote
controller
1. re-coding
2. change batter y of the same type
3. eliminating the dirt on the pieces
caused by corrosion
4. contact the local dealer to
change the matched remote
controller
1. re-coding
2. change batter y of the same type
3. eliminating the dirt on the pieces
caused by corrosion
4. contact the local dealer to
change the matched remote
controller
1.find the interfering source and
eliminate it
2.send the host back to the factor y
for repairing
3.check whether the power supply
is plugged well