Page 1
IBM Mobile Systems ThinkPad Computer Hardware Maintenance Manual July 2002 This manual supports: ThinkPad X30 (MT 2672/2673) ThinkPad Dock (MT 2631)
About this manual This manual contains service and reference information for IBM ThinkPad X30 (MT 2672/2673), and ThinkPad Dock (MT2631) products. Use this manual along with the advanced diagnostic tests to troubleshoot problems. The manual is divided into sections as follows:...
Advise customers to contact the PC Company HelpCenter at 800-772-2227 if they need assistance in obtaining or installing any diskette fixes. Customers in Canada should call IBM HelpPC at 800-565-3344 for assistance or download information. Strategy for replacing FRUs...
Diskette compatibility matrix The compatibility of each of the drives with the diskettes for it is as follows: Diskette Diskette Compatibility drive capacity 3.5-inch 1.0 MB Read and write 2.0 MB Read and write 4.0 MB Not compatible ThinkPad X30 (MT 2672/2673)
Safety notices Safety notices: multilingual translations In this manual, safety notices appear in English with a page number reference to the appropriate multilingual, translated safety notice found in this section. The following safety notices are provided in English, French, German, Italian, and Spanish. Safety notice 1 Before the computer is powered-on after FRU replacement, make sure all screws, springs, and other...
Page 10
Die Bereitschaftsbatterie, die sich unter dem Diskettenlaufwerk befindet, kann geringe Mengen Nickel und Cadmium enthalten. Sie darf nur durch die Verkaufsstelle oder den IBM Kundendienst ausgetauscht werden. Sie darf nicht zerlegt, wiederaufgeladen, kurzgeschlossen, oder Feuer oder Wasser ausgesetzt werden. Die Batterie kann schwere Verbrennungen oder Verätzungen...
Page 11
Safety notices (continuation of safety notice 2) Alcune batterie di riserva contengono una piccola quantità di nichel e cadmio. Non smontarle, ricaricarle, gettarle nel fuoco o nell’acqua né cortocircuitarle. Smaltirle secondo la normativa in vigore (DPR 915/82, successive disposizioni e disposizioni locali).
Page 12
(DPR 915/82, successive disposizioni e disposizioni locali). Quando si sostituisce la batteria, utilizzare soltanto i tipi inseriti nell’appropriato Catalogo parti. L’impiego di una batteria non adatta potrebbe determinare l’incendio o l’esplosione della batteria stessa. (continued) ThinkPad X30 (MT 2672/2673)
Page 13
Safety notices (continuation of safety notice 3) Las baterías contienen pequeñas cantidades de níquel. No las desmonte, ni recargue, ni las eche al fuego o al agua ni las cortocircuite. Deséchelas tal como dispone la normativa local. Utilice sólo baterías que se encuentren en la lista de piezas al sustituir la batería.
Page 14
No la recargue, ni quite el conector polarizado, ni la desmonte, ni caliente por encima de los 100°C (212°F), ni la incinere ni exponga el contenido de sus celdas al agua. Deséchela tal como dispone la normativa local. ThinkPad X30 (MT 2672/2673)
Page 15
Safety notices Safety notice 5 If the LCD breaks and the fluid from inside the LCD gets into your eyes or on your hands, immediately wash the affected areas with water for at least 15 minutes. Seek medical care if any symptoms from the fluid are present after washing.
Page 16
Per evitare scosse elettriche, non rimuovere la copertura in plastica che avvolge la parte inferiore della scheda invertitore. Para evitar descargas, no quite la cubierta de plástico que rodea la parte baja de la tarjeta invertida. ThinkPad X30 (MT 2672/2673)
Page 17
Safety notices Safety notice 7 DANGER Though the main batteries have low voltage, a shorted or grounded battery can produce enough current to burn personnel or combustible materials. Bien que le voltage des batteries principales soit peu élevé, le court-circuit ou la mise à la masse d’une batterie peut produire suffisamment de courant pour brûler des matériaux combustibles ou causer des brûlures corporelles graves.
Page 18
Antes de quitar una FRU, apague el sistema, desenchufe todos los cables de las tomas de corriente eléctrica, quite la batería y, a continuación, desconecte cualquier cable de conexión entre dispositivos. ThinkPad X30 (MT 2672/2673)
Safety information Safety information The following section presents the safety information that you need to be familiar with before servicing an IBM mobile computer. General safety Follow these rules to ensure general safety: v Observe good housekeeping in the area of the machines during and after maintenance.
Attention: An electrical shock can occur only when there is a complete circuit. By observing the above rule, you may prevent a current from passing through your body. ThinkPad X30 (MT 2672/2673)
This guide addresses only those items. You should use good judgment to identify potential safety hazards due to attachment of non-IBM features or options not covered by this inspection guide. Introduction...
Insulation must not be frayed or worn. 4. Remove the cover. 5. Check for any obvious non-IBM alterations. Use good judgment as to the safety of any non-IBM alterations. 6. Check inside the unit for any obvious unsafe conditions, such as metal filings, contamination, water or other liquids, or signs of fire or smoke damage.
Safety information damage by equalizing the charge so that the machine, the part, the work mat, and the person handling the part are all at the same charge. Notes 1. Use product-specific ESD procedures when they exceed the requirements noted here. 2.
Laser compliance statement Laser compliance statement Some IBM Personal Computer models are equipped from the factory with an optical storage device such as a CD-ROM drive or a DVD-ROM drive. They are also sold separately as options. The drive is certified in the U.S. to...
Page 25
Laser compliance statement When a CD-ROM drive, DVD drive or the other laser product is installed, note the following: CAUTION: Use of controls or adjustments or performance of procedures other than those specified herein might result in hazardous radiation exposure. O uso de controles, ajustes ou desempenho de procedimentos diferentes daqueles aqui especificados pode resultar em perigosa exposição...
Page 26
Non fissare il fascio, non guardarlo direttamente con strumenti ottici e evitare l’esposizione diretta al fascio. Radiación láser al abrir. No mire fijamente ni examine con instrumental óptico el haz de luz. Evite la exposición directa al haz. ThinkPad X30 (MT 2672/2673)
Page 28
Missing parts might be a symptom of unauthorized service or modification. v If the spindle of a hard-disk drive becomes noisy, it may have been subjected to excessive force, or dropped. ThinkPad X30 (MT 2672/2673)
Service web site When the latest maintenance diskette and the system program service diskette become available, a notice will be posted on http://www.ibm.com/pc/partner/infotips Restoring the preloaded system If the data on a hard-disk drive is damaged or accidentally erased, you can restore the software that was shipped with the computer.
(F1, F11, and F12) appear on the screen for a few seconds. One of them is “Press F11 to invoke the IBM Product Recovery program”. While the message is displayed, quickly press F11. If you are using Windows 2000 or another operating system, the startup screen is displayed first, and then the message “To start the Product Recovery...
Related service information Note: Network drivers are not automatically restored with Windows NT 4.0; you will need to reinstall them. Note: If you use Windows 2000 or Windows 98, restart the system by pressing Ctrl+Alt+Del or by turning the computer off and then on again. The computer will restart with the pre-installed operating system, drivers, and software.
Note: There are two modes for the HDP: User only and Master + User. The Master + User mode requires two HDPs; the system administrator enters both in the same operation. The system administrator then provides the user HDP to the system user. ThinkPad X30 (MT 2672/2673)
Supervisor password: A supervisor password (SVP) protects the system information stored in the IBM BIOS Setup Utility. The SVP must be entered in order to get access to the IBM BIOS Setup Utility and make changes to system configuration settings.
If User only mode is selected and the user HDP has been forgotten and cannot be made available to the servicer, IBM does not provide any services to reset the user HDPs or to recover data from the hard-disk drive.
Related service information v The hard-disk drive motor stops. 3. If the time set on the “Turn off monitor” timer in the operating system expires, v The LCD backlight turns off. To end screen blank mode and resume normal operation, press any key.
If you are using the ACPI operating system and have defined one of the following actions as the event that causes the system to go into hibernation mode, perform that action. – Closing the lid. – Pressing the power button. – Pressing Fn+F4 keys. ThinkPad X30 (MT 2672/2673)
Page 37
Related service information Also, the computer goes into hibernation mode automatically in either of the following conditions: v If a “hibernation time” has been set on the timer, and the user does not do any operation with the keyboard, the TrackPoint, the hard-disk drive, the parallel connector, or the diskette drive within that time.
For some possible configurations of the computer, PC-Doctor might not run correctly. To avoid this problem, you need to initialize the computer setup by use of the IBM BIOS Setup Utility before you run PC-Doctor. On the IBM BIOS Setup Utility screen, press F9, Enter, F10, and then Enter.
Page 39
To test Digital Signature Chip, the chip must be enabled. v When Legacy Floppy Drives is enabled in the IBM BIOS Setup Utility, Diskette Drives test is activated even if no legacy diskette drive is attached to the ThinkPad computer.
Surface Scan Hard Disk v Benchmark System v DOS Shell v Tech Support Form v Battery Rundown v View Test Log v Print Log v Save Log v Full Erase Hard Drive v Quick Erase Hard Drive ThinkPad X30 (MT 2672/2673)
Checkout guide Power system checkout To verify a symptom, do the following: 1. Power off the computer. 2. Remove the battery pack. 3. Connect the ac adapter. 4. Check that power is supplied when you power on the computer. 5. Power off the computer. 6.
1 (+) and 5 (−). See the following figure: Terminal Voltage (V dc) + 0 to + 12.6 1(+) Ground (−) 5(-) 3. If the voltage is less than +11.0 V dc, the battery pack has been discharged. ThinkPad X30 (MT 2672/2673)
Checkout guide Note: Recharging will take at least 3 hours, even if the indicator does not turn on. If the voltage is still less than +11.0 V dc after recharging, replace the battery. 4. If the voltage is more than +11.0 V dc, measure the resistance between battery terminals 4 and 5.
RJ45 v Parallel connector v Stereo headphone jack v Monaural microphone jack v Stereo line-in jack v Universal serial bus (USB) connector × 2 v Infrared port v Docking connector v DC-in v IEEE 1394 connector (continued) ThinkPad X30...
Page 48
Windows 2000 Models 2672-x2x, x5x, x6x, xBx, xEx, xHx, xLx, xPx, xSx, xVx, xXx, xYx, 2673-x2x, and xBx: Windows XP Professional Models 2672-x3x, xCx, xJx,xKx, xMx, xTx, xQx, and xWx: Windows XP Home edition ThinkPad X30 (MT 2672/2673)
Orange: The battery is being charged, but the battery power is still low. Blinking orange: The battery needs to be charged. When the indicator starts blinking orange, the computer beeps three times. (continued) ThinkPad X30...
Page 50
When this indicator is on, do not put the computer into standby mode or turn off the computer. Note: Do not move the system while the Green drive in use light is on. Sudden physical shock could cause drive errors. ThinkPad X30 (MT 2672/2673)
Applicable test System board 1. Diagnostics --> CPU/Coprocessor 2. Diagnostics --> Systemboard Power Diagnostics --> Other Devices --> IBM AC Adapter, IBM Battery 1 (IBM Battery 2) LCD unit 1. Diagnostics --> Video Adapter 2. Interactive Tests --> Video Modem or 1.
Turn hibernation mode on. To return to normal operation, press the power button for less than four seconds. Fn+PgUp Turn the ThinkLight on or off. Fn+Home The LCD becomes brighter. Fn+End The LCD becomes less bright. ThinkPad X30 (MT 2672/2673)
If the symptom is not described there, go to “Intermittent problems” on page 55. Note For an IBM device not supported by diagnostic codes in the ThinkPad notebook computers, see the manual for that device. Numeric error codes...
Page 54
2. System board. 0200 1. Reseat the hard-disk Hard disk error—The hard disk drive. is not working. 2. Load Setup Defaults in IBM BIOS Setup Utility. 3. Hard-disk drive. 4. System board. 021x Run interactive tests of the Keyboard error keyboard and the auxiliary input device.
Page 55
IBM BIOS Setup Utility to reset the time and date. 2. System board. 0271 Run IBM BIOS Setup Utility to Date and time error—Neither reset the time and date. the date nor the time is set in the computer.
3. System board. Operating system not found. 1. Check that the operating system has no failure and is installed correctly. 2. Enter IBM BIOS Setup Utility and see whether the hard-disk drive and the diskette drive are properly identified. 3. Reseat the hard-disk drive.
Only cursor appears. Reinstall operating system. Four cycles of four short beeps System board (IBM security and a blank screen. chip) Five short beeps and a blank System board screen.
1. See important note for v Characters missing pixels. “LCD-related symptoms.” v Screen abnormal. 2. Reseat all LCD connectors. v Wrong color displayed. 3. LCD assembly. 4. System board. Horizontal or vertical lines LCD assembly. displayed on LCD. ThinkPad X30 (MT 2672/2673)
2. Visually check each FRU for damage. Replace any damaged FRU. 3. Remove or disconnect all of the following devices: a. Non-IBM devices b. Devices attached to the port replicator c. Printer, mouse, and other external devices d. Battery pack e.
Read this section carefully before replacing any FRU. Screw notices Loose screws can cause a reliability problem. In IBM ThinkPad computer, this problem is addressed with special nylon-coated screws that have the following characteristics: v They maintain tight connections.
Note: The serial number of the system unit is written on the label attached on the bottom of the computer. Retaining the UUID The Universally Unique Identifier (UUID) is a 128-bit number uniquely assigned to your computer at production ThinkPad X30...
Page 62
1. Install the ThinkPad hardware maintenance diskette version 1.62, and restart the computer. 2. From the main menu, select 4. Assign UUID. A new UUID is created and written. If a valid UUID already exists, it is not overwritten. ThinkPad X30 (MT 2672/2673)
Attention: The system board is sensitive to, and can be damaged by, electrostatic discharge. Before touching it, establish personal grounding by touching a ground point with one hand or by using an electrostatic discharge (ESD) strap (P/N 6405959). ThinkPad X30...
Removing and replacing a FRU 1010 Battery pack DANGER Use only the battery specified in the parts list for your computer. The use of an incorrect battery can result in ignition or explosion of the battery. ThinkPad X30 (MT 2672/2673)
For access, remove following FRU: v “1010 Battery pack” on page 60 Note: The hard disk is attached to the cover. Step Screw (quantity) Torque M3 × 4 mm, nylon-coated (1) 0.4 Nm (4 kgfcm) (continued) ThinkPad X30...
Page 66
Removing and replacing a FRU When installing: Make sure that the hard disk is connected firmly. ThinkPad X30 (MT 2672/2673)
DIMM into the socket, and then press it firmly. Pivot the DIMM until it snaps into place. Make sure that the card is firmly fixed in the slot and does not move easily. ThinkPad X30...
“1010 Battery pack” on page 60 v “1020 Hard-disk drive” on page 61 Note: Loosen the screws 1 , but do not remove them. When installing: Make sure that the battery connector 4 is attached firmly. ThinkPad X30 (MT 2672/2673)
Removing and replacing a FRU 1050 Keyboard For access, remove following FRU: v “1010 Battery pack” on page 60 Step Screw (quantity) Torque M2 × 6 mm, nylon-coated (4) 0.245 Nm (2.5 kgfcm) (continued) ThinkPad X30...
Page 70
In step 4 , open the keyboard slightly in the direction of the arrow. In step 5 , draw the keyboard a little in the direction of the arrow, and then detach the connector 6 . ThinkPad X30 (MT 2672/2673)
Page 71
Removing and replacing a FRU When installing: Install the keyboard, do as follows; 1. Attach the connector. 2. Make sure that the keyboard edges, shown in the figure as (A) and (B), are under the frame. (continued) ThinkPad X30...
Page 72
4. To make sure that the front side of the keyboard is housed firmly, gently press the keys with your thumbs and try to slide the keyboard toward you. 5. Secure the keyboard by tightening the screws from the bottom side of the computer. ThinkPad X30 (MT 2672/2673)
This section is only for the models featuring the Mini PCI combo (wireless LAN and modem) card. For access, remove following FRUs, in order: v “1010 Battery pack” on page 60 v “1050 Keyboard” on page 65 (continued) ThinkPad X30...
Page 74
( 4a ) into jack J1, and the black antenna cable with the tab marked “AUX” ( 4b ) into jack J2. v With the notched end of the card toward the socket, insert the card into the socket, and then press it firmly. ThinkPad X30 (MT 2672/2673)
Page 75
Cable routing: When attaching the Mini PCI adapter, route the antenna cables to go under the cable guide as in a , and place the tabs as indicated by arrow b in this figure. ThinkPad X30...
“1020 Hard-disk drive” on page 61 v “1050 Keyboard” on page 65 Step Screw (quantity) Torque M2 × 9.5 mm, nylon-coated (5) 0.245 Nm (2.5 kgfcm) When installing: Make sure that the connector 3 is firmly attached. ThinkPad X30 (MT 2672/2673)
Page 77
Removing and replacing a FRU Note Apply thermal grease on the a -part of the fan, shown in the following figure. ThinkPad X30...
For access, remove following FRUs, in order: v “1010 Battery pack” on page 60 v “1020 Hard-disk drive” on page 61 v “1050 Keyboard” on page 65 Step Screw (quantity) Torque M2 × 9.5 mm, nylon-coated (2) 0.245 Nm (2.5 kgfcm) (continued) ThinkPad X30 (MT 2672/2673)
Removing and replacing a FRU Modem daughter card (MDC) When installing: Make sure that connectors 2 and 3 are attached firmly. ThinkPad X30...
Page 80
Removing and replacing a FRU Cable routing: When attaching the MDC, route the cable along the cable guides as indicated by the arrows in this figure. ThinkPad X30 (MT 2672/2673)
Unplug the jack by pulling the tab with your fingers. When installing: 1. Plug the white cable with the tab marked “BT” into the jack on the BDC. 2. Make sure that the connector 2 is attached firmly. ThinkPad X30...
Page 82
Removing and replacing a FRU Cable routing: When attaching the BDC, route the cable along the cable guides as indicated by the arrows in this figure. ThinkPad X30 (MT 2672/2673)
Page 84
Removing and replacing a FRU Step Screw (quantity) Torque M2 × 4 mm, nylon-coated (5) 0.245 Nm (2.5 kgfcm) (continued) ThinkPad X30 (MT 2672/2673)
Page 85
2. Make sure that all of the latches on the front side of the computer are attached firmly. 3. Secure the keyboard bezel with the screws. ThinkPad X30...
“1030 DIMM” on page 63 v “1040 Backup battery” on page 64 v “1050 Keyboard” on page 65 v “1090 Keyboard bezel” on page 79 Step Screw (quantity) Torque M2 × 4 mm, nylon-coated (2) 0.245 Nm (2.5 kgfcm) (continued) ThinkPad X30 (MT 2672/2673)
Page 87
Removing and replacing a FRU Unlatch the PC Card slot by pressing the two parts indicated by arrow 2 , and then remove the slot in the direction of arrow 3 . ThinkPad X30...
Page 88
3. Attach the slot in the direction of arrow c , and make sure that both of the latches are attached firmly. 4. Secure the slot with the screws. ThinkPad X30 (MT 2672/2673)
“1090 Keyboard bezel” on page 79 Before removing the LCD assembly, remove the hinge cover first by following steps 1 and 2 . Step Screw (quantity) Torque M2 × 9.5 mm, nylon-coated (2) 0.245 Nm (2.5 kgfcm) (continued) ThinkPad X30...
Page 90
2 . When installing: Attach the hinge cover, aligning the two projections on the rear side with the two small square holes in the base cover. ( a ) ThinkPad X30 (MT 2672/2673)
Page 91
Removing and replacing a FRU After removing the hinge cover, remove the LCD assembly as follows: Step Screw (quantity) Torque M2.5 × 4.8 mm, nylon-coated (4) 0.392 Nm (4 kgfcm) When installing: Make sure that the connector 4 is firmly attached. (continued) ThinkPad X30...
Page 92
Removing and replacing a FRU Step Screw (quantity) Torque M2.5 × 4.8 mm, nylon-coated (2) 0.392 Nm (4 kgfcm) Cable routing: After attaching the LCD assembly, route the antenna cables as follows: ThinkPad X30 (MT 2672/2673)
“1090 Keyboard bezel” on page 79 Step Screw (quantity) Torque M2 × 4 mm, nylon-coated (2) 0.245 Nm (2.5 kgfcm) When installing: Make sure that the connector 2 on the bottom side of the card is firmly attached to the system board. ThinkPad X30...
“1080 Communication daughter card (CDC)” on page 74 (only for the models with the CDC) v “1090 Keyboard bezel” on page 79 Before removing the speaker assembly, remove the keyboard CRU insulator 1 . (continued) ThinkPad X30 (MT 2672/2673)
Page 95
M2 × 14 mm with washer, 0.245 Nm nylon-coated (1) (2.5 kgfcm) Cable routing: When installing the speaker assembly, attach the connector first. Then route the cable along the cable guides of the base cover as indicated by the arrows in this picture. ThinkPad X30...
Before removing the system board, remove the hard-disk drive holder (steps 1 and 2 ) and the cable guide (steps 3 to 5 ). Step Screw (quantity) Torque M2 × 9.5 mm, nylon-coated (2) 0.245 Nm (2.5 kgfcm) (continued) ThinkPad X30 (MT 2672/2673)
Page 97
Removing and replacing a FRU Step Screw (quantity) Torque M2 × 9.5 mm, nylon-coated (1) 0.245 Nm (2.5 kgfcm) When installing: Make sure that the connectors 4 are attached firmly. (continued) ThinkPad X30...
Page 98
FRU. When installing: Attach the system board so that the two small projections on the base cover fit into the holes provided, and then tighten the screws. ThinkPad X30 (MT 2672/2673)
M2 × 4 mm, nylon-coated (1) 0.245 Nm (2.5 kgfcm) When installing: Make sure that all of the latches of the LCD front bezel are firmly attached to the LCD cover. Then secure the bezel with the screws. ThinkPad X30...
“1110 Hinge cover and LCD assembly” on page 85 v “2010 LCD front bezel” on page 95 If the ThinkPad computer you are servicing has the Bluetooth features, remove Bluetooth button cover 4 from the defective inverter card and keep the cover for reuse. ThinkPad X30 (MT 2672/2673)
Page 101
FRU to the computer. 2. Make sure that both of the connectors 2 , 3 are attached firmly. Cable routing: When replacing the inverter card, route the connector cable as in the following figure: ThinkPad X30...
“2010 LCD front bezel” on page 95 v “2020 Inverter card” on page 96 For models with no wireless LAN antenna Step Screw (quantity) Torque M2 × 4 mm, nylon-coated (6) 0.245 Nm (2.5 kgfcm) (continued) ThinkPad X30 (MT 2672/2673)
Page 103
Removing and replacing a FRU (continued) ThinkPad X30...
Page 104
M2 × 3 mm, nylon-coated (6) 0.2 Nm (2 kgfcm) When installing v Do not pinch the antenna cables under the LCD panel. v Make sure that the antenna cables are firmly routed along the cable guides of the LCD cover. ThinkPad X30 (MT 2672/2673)
Removing and replacing a FRU For wireless LAN models Step Screw (quantity) Torque M2 × 4 mm, nylon-coated (6) 0.245 Nm (2.5 kgfcm) Release the antenna cables from the cable guides indicated by the arrows 2 in this figure. (continued) ThinkPad X30...
Page 106
Removing and replacing a FRU (continued) ThinkPad X30 (MT 2672/2673)
Page 107
Removing and replacing a FRU Attach the white cable a to the right bracket, and attach the black cable b to the left bracket. Step Screw (quantity) Torque M2 × 3 mm, nylon-coated (6) 0.245 Nm (2.5 kgfcm) (continued) ThinkPad X30...
Page 108
Place the FPC connector to pass under the black antenna cable. v Do not pinch the antenna cables under the LCD panel. v Make sure that the antenna cables are firmly routed along the cable guides of the LCD cover. ThinkPad X30 (MT 2672/2673)
05K6246) v ThinkPad Dock with extension plate: FRU no. 08N1537 (PCI cover: FRU no. 08N7317) Confirm the FRU no. of the ThinkPad Dock first and choose the proper PCI cover FRU for the ThinkPad Dock you are servicing. ThinkPad X30...
Page 110
Note: The following illustration shows how to remove the PCI cover of ThinkPad Dock (FRU no. 08N1546). Do the same to remove the PCI cover of ThinkPad Dock with extension plate (FRU no. 08N1537). (Bottom view) ThinkPad X30 (MT 2672/2673)
08N1546). The top cover and screw kit for ThinkPad Dock (FRU no. 12P4143) is not available for the ThinkPad Dock with extension plate (FRU no. 08N1537) . (Rear view) Step Screw (quantity) Torque M2.5 × 4.8 mm (2) 0.392 Nm (4 kgfcm) (continued) ThinkPad X30...
Page 112
Removing and replacing a FRU (Bottom view) Step Screw (quantity) Torque M2.5 × 4.8 mm (8) 0.392 Nm (4 kgfcm) (continued) ThinkPad X30 (MT 2672/2673)
Page 113
Make sure that the system lock key A is set to the Unlock position. Release the front latches in step 3 , and then remove the top cover 4 . For step 5 , see the inside view, shown in the circle. ThinkPad X30...
Page 114
Removing and replacing a FRU When replacing the top cover, do the following: v Make sure that the springs are placed correctly. v Make sure that the device release lever is seated correctly. (continued) ThinkPad X30 (MT 2672/2673)
Page 115
Removing and replacing a FRU v Make sure that the release button works correctly. ThinkPad X30...
Bluetooth button (some models) Bluetooth status indicator (some models) Power status indicators Power switch Security keyhole Universal serial bus (USB) connector Hard-disk drive TrackPoint pointer TrackPoint buttons ThinkPad button Volume and mute buttons System status indicators ThinkLight ThinkPad X30 (MT 2672/2673)
Locations Rear view Modem connector Ethernet connector USB connector External-monitor connector Parallel connector AC power connector Power status indicators Bluetooth status indicator (some models) ThinkPad X30...
An Ultrabay device is ready to be attached or detached. Ultrabay device eject lever UltraBase eject button UltraBase status indicator Green: An UltraBase X3 is attached to the computer and in use. Turn off: An UltraBase X3 is ready to be attached or detached. ThinkPad X30...
Page 123
Keyboard bezel assembly (Korea) 27L6747 v 2672-xxK v 2673-42K, 4BK Hard-disk drive (20 GB) 9.5 mm 4200 rpm, 27L4286* IBM STD OP v 2672-1xx, 3xx Hard-disk drive (20 GB) 9.5 mm 4200 rpm, 08K9533* HITACHI v 2672-1xx, 3xx Hard-disk drive (40 GB) 9.5 mm 4200 rpm,...
Page 124
Base cover assembly for 2672 WW IBM 27L6733 Wireless Mini-PCI v 2672-xAA, xBA, xEA, xBB, xBE, xAF, xBF,...
Page 125
Parts list Base cover assembly for 2672 Taiwan IBM 46P3152 Wireless Mini-PCI v 2672-4BT, 4ET Base cover assembly for 2672 Taiwan IBM 46P3153 Wireless Mini-PCI+BT v 2672-4HT, 4JT, 4VT Base cover assembly for 2672 Korea 46P3156 v 2672-32K, 33K, 42K, 43K, 45K...
Page 126
41x, 42x, 43x, 45x, 46x, 4Nx, 4Px, 4Qx, 54x, 64x, 7Mx v 2673-42x PC card slot 27L6737 IBM High Rate Wireless LAN Mini-PCI Adapter v 2672-1Ax, 1Bx, 4Ax, 4Bx, 4Cx, 4Ex, 4Gx, 26P8437 4Hx, 4Jx, 4Rx, 4Sx, 4Tx, 4Vx, 4Wx, 5Dx, 26P8442...
Page 127
3-pin (56 W), LITEON (models xxA, xxB, xxC, 02K6815* xxG, xxH, xxK, xxM, xxT) for optional AC adapters, see “Optional FRUs” on page 130. — Recovery CD (see “Recovery CDs” on page 127.) ThinkPad X30...
02K6164* Hebrew 02K6161* Italian 02K6151* Japanese 02K6140* Korean 02K6156* Norwegian 02K6149* Polish 02K6167* Portuguese 02K6154* Russian 02K6160* Slovak 02K6166* Slovenian 02K6168* Spanish, European 02K6155* Spanish, Latin American 02K6152* Swedish or Finnish 02K6148* Swiss 02K6153* Turkish 02K6158* ThinkPad X30 (MT 2672/2673)
Windows XP Home edition is preinstalled as the operating system in following models: v 2672-x3x, xCx, xJx,xKx, xMx, xTx, xQx, and xWx Language Chinese, Simplified 67P4610* Chinese, Traditional 67P4607* Chinese, Traditional (Hong Kong S.A.R.) 67P4613* English, AP 01R5601* ThinkPad X30 (MT 2672/2673)
(h) Hinge cover v Easy button cover v (f) Retainer, audio connector v Screw caps Note: Italicized letters in parentheses are references to the exploded view on page 118. System board miscellaneous parts: 27L6736 v I/O plate ThinkPad X30...
64-MB SDRAM SO DIMM (PC133) 19K4651* 512-MB SDRAM SO DIMM (PC133) 19K4657* Hard-disk drive (40 GB) 9.5 mm 5400 rpm, IBM STD 27L4384* Hard-disk drive (60 GB) 12.5 mm 4200 rpm, IBM 08K9700* Hard-disk drive (60 GB) 9.5 mm 4200 rpm, HITACHI...
Page 135
08K6105* USB cable attachment 08K6108* USB cable 27L0542* Bluetooth UltraPort module 09N9813* ThinkPad Dock with extension plate 08N1537* PCI cover 08N7317* Top cover and screw kit for ThinkPad Dock 12P4143* ThinkPad Port Replicator 08N1536* Multiple battery charger 02K6642* ThinkPad X30...
— 1.62 Note: Download the file from the following Web site: http://www.ibm.com/pc/partner/infotips Power cords (system) IBM power cords for a specific country or region are usually available only in that country or region: For 2-pin power cords: Region Canada, U.S.
Notices Notices References in this publication to IBM products, programs, or services do not imply that IBM intends to make these available in all countries in which IBM operates. Any reference to an IBM product, program, or service is not intended to state or imply that only that IBM product, program, or service may be used.
Page 138
Part Number: 24P2962 (1P) P/N: 24P2962...
Need help?
Do you have a question about the thinkpad x30 and is the answer not in the manual?
Questions and answers