Advertisement
Quick Links
Advertisement
Related Manuals for USCutter SC
Summary of Contents for USCutter SC
- Page 1 User Manual & Assembly Instructions...
- Page 2 Cut and place vinyl like a pro Oracal 8510 gives the professional appearance Thank you for purchasing the SC vinyl cutter. Please read this manual of etched glass for a fraction of the price and completely and keep it in a safe place for future reference.
- Page 3 Vinyl Software when you locate your vinyl cutting headquarters. Position the SC Cutter near enough to your computer to be able to attach it via USB cable or 9-pin serial cable. Internet access will be necessary for downloading drivers and software.
-
Page 4: Before You Begin
Line up the foot and the leg so that the four holes in the leg that look like this line up with Repeat with the other leg and foot making sure the rounded edge faces out and the four holes on the foot. the holes for the cross piece are close to the top. 425.481.3555 www.uscutter.com 425.481.3555 www.uscutter.com... - Page 5 Mount the SC Cutter (B) to the mounting brackets (G) on the stand. Lift the SC NOTE: If your roller brackets arrived in four pieces instead of two, simply...
- Page 6 Used by the cutter to determine the location of cut contours replacing carriages. Contains the power cable port, power switch, and fuse cartridge for the LEFT SIDE COVER cutter. LOCKING KNOB RIGHT SIDE COVER Contains the USB and serial cable ports for the cutter. 425.481.3555 www.uscutter.com 425.481.3555 www.uscutter.com...
- Page 7 You can download and install the VinylMaster Cut software at www.uscutter.com/download, and you will need the key code packaged with this cutter to activate the software. You may need Release the pinch rollers release levers.
- Page 8 3 or more rollers, one roller near the center). Avoid lowering a pinch roller Engage the Pinch Rollers by pushing down on the to the gap between the two feed rollers. Pinch Roller Release Levers. If the cutter is not already on, turn it on now. 425.481.3555 www.uscutter.com 425.481.3555 www.uscutter.com...
- Page 9 Blade Carriage. To set the Origin of where the SC cutter will begin To set speed and force of the SC cutter, make sure you position. cutting from press the “Enter” button on “Local” while on are back in the “Home”...
- Page 10 This setting determines how hard the blade comes down onto the material. outer square INCREASE won’t weed FORCE Most vinyl products blade digging too far DECREASE FORCE loaded from over the top. into carrier weeds easily with a light- PERFECT! ly scored carrier Test Cut 425.481.3555 www.uscutter.com 425.481.3555 www.uscutter.com...
-
Page 11: Adjusting The Offset
“Next”. Repeat this process for registration mark calibrating your laser it’s time to print your image. number “3”. Click the “Cut” button and the cutter will briefly return to it’s home position and complete the cut. 425.481.3555 www.uscutter.com 425.481.3555 www.uscutter.com... - Page 12 Change the offset setting. coating the blade with WD40 and moving it in and out of the blade holder. Clean off any debris that comes out. Replacement blade holder may be needed. RAISE OFFSET LOWER OFFSET 425.481.3555 www.uscutter.com 425.481.3555 www.uscutter.com...
- Page 13 Indoor Wall GreenStar Wall Vinyl cutting strips. Go to Oratape HT55 Vinyl USCUTTER.com and search using Refer to the manual section on Blade the keyword: Cutting Strip. Set-up for instructions on how to install re- placement blades and remember to dispose of •...
- Page 14 For permission requests, write to USCutter, 7945 NE 65th St., Suite 200, Redmond, WA 98052 6/27/2016...
Need help?
Do you have a question about the SC and is the answer not in the manual?
Questions and answers