Related Manuals for ECOVACS WINBOT 950
Summary of Contents for ECOVACS WINBOT 950
-
Page 1: Instruction Manual
Instruction Manual Note: This Instruction Manual applies to units purchased in North America only. - Page 2 Before you go any further, please register your product on the ECOVACS ROBOTICS website at www.ecovacsrobotics.com/registration/. We also suggest you record your model number, serial number, date of purchase and attach your receipt to this page for safekeeping.
-
Page 3: Table Of Contents
Contents 1. Important Safety Instructions...............2 2. Package Contents and Technical Specifications........4 2.1 Package Contents..................4 2.2 Specifications....................4 2.3 Product Diagram..................5 3. Operating WINBOT..................6 3.1 Notes before Cleaning................6 3.2 Attach Cleaning Pad.................7 3.3 Assemble Power Adapter................7 3.4 Install Safety Tether...................8 3.5 Place Safety Pod..................9 3.6 Spray Cleaning Solution................10 3.7 Start......................10 3.8 Pause......................12... -
Page 4: Important Safety Instructions
1. Important Safety Instructions When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE. SAVE THESE INSTRUCTIONS 1. This Appliance is not intended to be used by children under 8 or anyone lacking knowledge on proper use. - Page 5 25. Do not incinerate the Appliance even if it is severely damaged. The battery can explode in a fire. 26. The Appliance must be used in accordance with the directions in this Instruction Manual. ECOVACS ROBOTICS cannot be held liable or responsible for any damages or injuries caused by improper use. FR-CA...
-
Page 6: Package Contents And Technical Specifications
2. Package Contents and Technical Specifications 2.1 Package Contents Safety Pod and Remote Control WINBOT Power Adapter Instruction Manual with Batteries Tether (3) Cleaning Pads WINBOT (1) WINBOT Finishing Cloth Cleaning Solution Extension Cord (1.5m/4’11”) 2.2 Specifications WINBOT model W950 Working Voltage 24V DC Rated Power... -
Page 7: Product Diagram
2. Package Contents and Technical Specifications 2.3 Product Diagram WINBOT 1. Speaker 10. Bottom Status Indicator Light 2. Status Indicator Light/START/PAUSE Button 11. Suction Sensor 3. Handle 12. Fan 4. Upgrade Port (for after-sale service) 13. Driving Treads 5. Power Cord 14. -
Page 8: Operating Winbot
3. Operating WINBOT 3.1 Notes Before Cleaning Do not use WINBOT on a framed window WINBOT can clean framed or frameless glass, with a frame smaller than 5mm (0.2”). larger than 45cm x 45cm (17.7’’ x 17.7’’). If WINBOT ’s Status Indicator Light flashes If the window is covered with dirt, clean a GREEN af ter power ing ON, the Back-Up small area on the glass before use and place... -
Page 9: Attach The Cleaning Pad
Please refer to the glass manufacturer's care and cleaning instructions before using WINBOT on glass with an uneven surface, such as frosted, textured, patterned, or coated glass. ECOVACS ROBOTICS cannot be responsible for damage due to improper use on these surfaces. -
Page 10: Install The Safety Tether
3. Operating WINBOT 3.4 Install the Safety Tether End A: WINBOT Power Cord End B: Power Adapter Power Cord End C: Safety Pod End D: Safety Tether Loop one end of the Safety Tether to End A on the WINBOT Power Cord and tighten. -
Page 11: Place The Safety Pod
3. Operating WINBOT Loop the other end of the Safety Te t h e r a r o u n d t h e S a f e t y Po d ’s channel and pull it tight. * If the length of the power cord restricts WINBOT’s movement, a WINBOT Extension Cord can be used. -
Page 12: Spray Cleaning Solution
3. Operating WINBOT 3.6 Spray Cleaning Solution * It is recommended to use WINBOT with WINBOT Cleaning Solution from ECOVACS. Using tap water or other cleaners could have an adverse effect on cleaning performance. Using other cleaning solutions could potentially nullify the warranty. - Page 13 3. Operating WINBOT Power ON Move the Power Switch to the “ ” position. WINBOT is powered ON when the Status Indicator Light flashes BLUE. * Keep objects away from WINBOT’s Fan to avoid blockage. Place on the Glass Place WINBOT on the window at least 10cm (4”) from window corners or other obstacles.
-
Page 14: Pause
3. Operating WINBOT 3.8 Pause Pause WINBOT during cleaning by pressing Direct WINBOT to move forward, backward, left the START/PAUSE button on the robot or on and right using the Direction Control Buttons on the Remote Control. the Remote Control when Paused. WINBOT cleans when the Direction Control Buttons are used. - Page 15 3. Operating WINBOT Remove the Safety Pod. Unplug WINBOT Polish away any marks left on the glass from the Safety Pod’s removal with the provided Finishing Cloth. Notes: If WINBOT has a problem and the indicator Light flashes RED, it can be reset by pressing the RESET Button on the Remote Control.
-
Page 16: Maintenance
4. Maintenance Before performing cleaning and maintenance on WINBOT, Power OFF and unplug WINBOT from the receptacle. 4.1 Cleaning Pad Turn WINBOT over and remove the Cleaning Pad. Soak the Cleaning Pad in cool, clean water for 2 minutes. Hand wash with mild detergent and lay flat to dry. -
Page 17: Driving Treads
4. Maintenance Edge Detection Sensors Squeegee Turn WINBOT over and wipe the four Edge Turn WINBOT over and wipe the Squeegee Detection Sensors clean with the provided with the provided Finishing Cloth to maintain its Finishing Cloth to maintain their effectiveness. effectiveness. -
Page 18: Status Indicator Light And Sounds
5. Status Indicator Light and Sounds Indicator Description Status Indicator Light Back-Up Battery is low and is charging. WINBOT will not clean until flashes GREEN the Back-Up Battery is properly charged. Status Indicator Light The Status Indicator Light stops glowing when the Back-Up Battery stops glowing is fully charged. -
Page 19: Troubleshooting
6. Troubleshooting Malfunction Possible Causes Solutions Pause WINBOT by pressing the WINBOT is cleaning. When START/PAUSE button on the robot WINBOT is cleaning, only the or Remote Control. Other buttons START/PAUSE Button works on on the Remote Control will function the Remote Control. - Page 20 6. Troubleshooting Malfunction Possible Causes Solutions A. Connect WINBOT to the Power Adapter and plug into the wall receptacle. Press Start/Pause Button on WINBOT or on the Remote Control. WINBOT will resume cleaning. Interruption of electricity while B. In case of power failure, and the WINBOT was cleaning due to above solution does not work, please power failure, plug displacement,...
- Page 21 6. Troubleshooting Malfunction Possible Causes Solutions A. Spray additional Cleaning Solution on the Cleaning Pad. B. Clean the Driving Treads as described in section 4. C. Replace the Cleaning Pad and restart the cleaning cycle. D. Use the Remote Control to control WINBOT moves in the cleaning by pressing Direction There is too much dirt and debris...
- Page 22 Designed and Manufactured by / Conception et fabrication par/Diseñado y Fabricado por ECOVACS ROBOTICS, Co., Ltd. MADE IN CHINA/FAIT EN CHINE/HECHO EN CHINA Distributed by/Distribué par/Distribuido por ECOVACS ROBOTICS, Inc. W950-AM01-IM2016R00 Canton, OH, USA/Canton, OH, EE.UU.
Need help?
Do you have a question about the WINBOT 950 and is the answer not in the manual?
Questions and answers