Advertisement
General Information
PLEASE READ THROUGH BEFORE BEGINNING ASSEMBLY.
IMPORTANT: Check boxes for Contents Listed
Check inside of parts as some parts are packaged
inside of others
In the event of missing, damaged or defective parts
please call our customer service dept. at 1-877-258-6020
When assembling components, place on a clean, flat
non-abrasive surface to avoid scratches
Tools Required
... Battery or Electric Drill
... Two 7/16" wrenches or sockets
... Tape Measure
... File
with #2 phillips bit, ¼", ⅛" drill bits
6' Picnic Table
11114
Model#
Part #
1
1½ x 5½ x 72" Table Rail
2
1½ x 5½ x 72" Table Rail
3
1½ x 5½ x 72" Seat Rail
4
1½ x 5½ x 59½" Cross Brace
5
1½ x 5½ x 30¼" Leg
6
25½" Table Bracket
7
8¾" Seat Bracket
8
⅞ x 1½ x 27" Center Brace
9
⅞ x 1½ x 26½" Diagonal Brace
10
28" Table End Cap
11
11 ⅛" Seat End Cap
12
6 ⅛" Leg End Cap
13
5½" Cross Brace End Cap
14
Hardware Bag
⅞ x 1½" End Cap
¾" Painted Screw
2" Painted Screw
¼ x 3½" Bolt
¼ x 2¼" Bolt
¼" Nylock Nut
¼" Flat Washer
Super Glue Tube
150 Birch Road
P.O. Box 122
Sheboygan Falls, WI 53085
Assembly Instructions
Description
Box#
1
(with wood)
1
2
(with wood)
1
2
(with wood)
2
2
2
2
2
2
2
2
2
(includes:)
1-877-258-6020
www.dura-trel.com
sales@dura-trel.com
Qty
3
2
4
2
4
2
4
1
2
2
4
4
4
1
2
72
12
8
18
26
52
2
1
Advertisement
Table of Contents
Related Manuals for Dura Trel 11114
Summary of Contents for Dura Trel 11114
-
Page 1: General Information
6' Picnic Table 11114 Model# Assembly Instructions Part # Description Box# 1½ x 5½ x 72" Table Rail (with wood) 1½ x 5½ x 72" Table Rail 1½ x 5½ x 72" Seat Rail (with wood) 1½ x 5½ x 59½" Cross Brace 1½... -
Page 2: Warranty Statement
If a Dura-Trel, Inc. product is determined to have a manufacturing defect which is covered by this warranty, Dura-Trel, Inc. will replace the material containing the defect (labor not included) F.O.B from the point of manufacture. Dura-trel, Inc. will not be responsible for any cost incurred in the removal or reinstallation of the product. - Page 3 TABLE TOP ASSEMBLY Lay out five 72" table top rails (part 1 and 2) as shown above with pilot holes facing up. Table top rails have two holes in the center of each rail, seat rails do not. Be sure wood inserts are flush with vinyl. Set two 25½" table brackets (part 6) over pilot holes at each end of table top rail, leaving ⅛"...
-
Page 4: Seat Assembly
SEAT ASSEMBLY Lay out two 72" seat rails (part 3) with pilot holes facing up. Seat rails do no have any holes in the center of each rail. Be sure wood inserts are flush with vinyl. Set two 8¾" seat brackets (part 7) over pilot holes at each end of seat rail, leaving ⅛"... - Page 5 CROSS BRACE / LEG ASSEMBLY Lay out two 30¼" legs (part 5) on an angle with pre-drilled holes for attaching table top, nearest each other at top. Lay one 59½" cross brace (part 4) across legs; adjusting legs so bolt holes line up. (Due to wood inserts in legs drying out, it may be necessary to ream holes out using a ¼"...
- Page 6 Insert one cross brace / leg assembly into brackets on underside of table top with cross brace closest to table end. Using four 2¼" bolts, washers and nuts, fasten assembly to table top. Repeat with second cross brace / leg assembly for opposite end of table. Using one 2¼"...
- Page 7 6' Picnic Table 11114 1½ x 5½ x 72" PT Table Rail 3.00 1½ x 5½ x 72" PT Table Rail 2.00 1½ x 5½ x 72" PT Seat Rail 4.00 1½ x 5½ x 59½" PT Cross Ra 2.00 1½...
Need help?
Do you have a question about the 11114 and is the answer not in the manual?
Questions and answers