Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Holman iWeather WS2813A
Summary of Contents for Holman iWeather WS2813A
- Page 1 Weather Link WS2813A INSTRUCTION MANUAL...
-
Page 2: Table Of Contents
Table of Contents Technical Data......p1-p3 Weather Forecast........p12 Glossary........p4-p5 Moon Phase Display......p13 Initial Operation......p6 Living Space Humidity & Battery..p14 Wireless Connection & Tips....p15 Programming Weather Record Notes Pages..p16-p17 Manual Time Setup....p7-p8 Daily Alarm Setup......p9 Warranty / QR Code....Back Page Snooze / 12-24Hr / ºC-ºF....p10 Temperature Alert Setup....p11... -
Page 3: Technical Data
Technical Data WS2813A HOLMAN iWeather Weather Link Thank you for purchasing this device, please read the operating instructions carefully to familarize yourself with the features and modes of operation before using the Weather Station. - Page 4 Technical Data - Cont. Technical Details: Indoor Unit • Six keys: MODE, +, - , ALERT, CHANNEL, SNOOZE/LIGHT. • Time display in 12/24 format • Continuous perpetual calendar up to 2099 • Display of Date, Month and Day of week •...
- Page 5 Technical Data - Cont. • Indoor/outdoor temperature and humidity • Thermometer measuring range inside: 0°C to +50 °C , outside -20°C~60 °C • Temperature display elective in °C or °F • Temperature alert • Moon phase • Living Space Feeling Outdoor sensor: •...
-
Page 6: Glossary
Glossary 1. Time 6. outdoor humidity 12. Weeks 2. Radio controlled symbol 7. Weather forecast 13. Moon phase 8. Living space feeling 14. Day of week in 7 languages (not applicable in Australia) 3. Summer time symbol 9. Indoor Humidity 15. -
Page 8: Initial Operation
Initial Operation - Outdoor Sensor & Indoor Sensor Outdoor Sensor • Please install batteries in the Outdoor Sensor first. • Open the battery compartment located on the rear side of the device. Place the batteries in the battery compartment. Observe the shown polarity. •... -
Page 9: Programming Manual Time Setup
Programming - Manual Time Setup Manual time set-up (most important to quit the reception of radio controlled signal by holding the minus button for 3 seconds in case it starts to flash before setup.) • Press and hold “MODE“ for 3 seconds. •... - Page 10 Programming - Manual Time Setup - Cont. • The display for the month is flashing. Use “+ “ and “-“ to select the month. Press “MODE “ to confirm. • The display for the date is flashing. Use “+ “ and “-“ to select the date. Press “MODE “ to confirm. •...
-
Page 11: Daily Alarm Setup
Programming - Daily Alarm Setup • Press “MODE” to switch from time display to A1 display. • Press and hold the key “MODE” for 3 seconds, the flashing alarm time is shown. • The hour display of the alarm time will flash. Use “+“ or “-“ to select hour. Press “MODE “ to confirm. •... -
Page 12: Snooze / 12-24Hr / ºc-ºf
Programming - Snooze / 12-24Hr / ºC-ºF Snooze function - To activate the snooze function, follow the steps below • Press the key “SNOOZE/LIGHT“, while the alarm sounds, to activate the snooze function. • If the snooze function is activated, snooze symbol is flashing. •... -
Page 13: Temperature Alert Setup
Programming - Temperature Alert Setup • Press “CHANNEL” to select the channel (CH1, CH2, CH3) if more than one outdoor sensor are within reach. • Press the key “ALERT” the temperature alert symbol is activated. • Hold the key “ALERT” for 3 seconds until the temperature alert symbol is flashing. •... -
Page 14: Weather Forecast
Weather Forecasts 4 Weather Forecasts Sunny Slightly sunny Cloudy Rainy Note: As the weather is forecasted by temperature, humidity only, the display will have a discrepancy with the actual weather occasionally. Illumination Press the key “SNOOZE/LIGHT“ to activate the display illumination for 5 seconds. -
Page 15: Moon Phase Display
Moon Phase Display The weather station uses saved data to show the moon phase. A: New moon B: increasing crescent C: First half D: increasing 3/4 E: Full moon F: decreasing 3/4 G: Last half H: decreasing crescent... -
Page 16: Living Space Humidity & Battery
Living Space Humidity & Battery The weather station uses saved data to determine the humidity in the living space and shows the respective symbols: below 40% Comfortable 40% - 70% (Temperature Display: 20 - 28°C) Comfortable Humid Humid 70% - 90% Low Battery Condition Display The weather station displays the low battery condition symbol to warn you that the weather station or the outdoor sensor need to have the batteries exchanged. -
Page 17: Wireless Connection & Tips
Wireless Connection & Tips Wireless connection to the Outdoor Sensor • Press the key “CHANNEL” to select a channel. You can read the data of up to 3 sensors at one weather station. • Press and hold the key “CHANNEL” for 3 seconds to search for outdoor sensors. Tips - When placing both the inside and outside units remember they are subject to interference. -
Page 18: Weather Record Notes Pages
Weather Record Notes Page... - Page 19 Weather Record Notes Page...
- Page 20 Warranty: We will honour all statutory guarantees that this product is of acceptable quality. (including that it is fit for purpose) HOLMAN Industries: 47 Walters Drive, Scan the QR Code above to see Osborne Park, WA 6017. more information on this product...
Need help?
Do you have a question about the iWeather WS2813A and is the answer not in the manual?
Questions and answers