Do you have a question about the Clio 2007 and is the answer not in the manual?
Questions and answers
Jayne Wilkinson
April 13, 2025
Key fob not working
1 comments:
Mr. Anderson
April 13, 2025
To fix a non-working key fob for a 2007 Renault Clio, first check if the battery needs replacing. If replacing the battery does not solve the issue, check that the doors and tailgate are properly closed. If the issue persists, contact a Renault dealer for further assistance.
Page 2
RENAULT vehicles. ELF lubricants are a major factor in your vehicle’s performance. RENAULT recommends the approved ELF lubricants for your oil changes and top-ups. Contact your RENAULT representative or visit the site: www.lubricants.elf.com The oil born in Formula One...
Sections Getting to know your vehicle ....... Driving ..............Your comfort ............Maintenance ............Practical advice ............ Technical specifications ........Alphabetical index ..........
Page 5
TYRE PRESSURE WHEN COLD (in bar or kg/cm² when cold) 1.4 16V Versions 1.6 16V 1.2 16V 1.5 dCi Tyre dimensions 175/65 R14 T 175/65 R14 T 185/55 R15 H 185/55 R15 H 185/55 R15 H Normal use (1) – Front –...
Page 6
TYRE PRESSURE WHEN COLD (in psi when cold) 1.4 16V Versions 1.6 16V 1.2 16V 1.5 dCi Tyre dimensions 175/65 R14 T 175/65 R14 T 185/55 R15 H 185/55 R15 H 185/55 R15 H Normal use (1) – Front – Rear Motorway use (1) –...
Page 9
KEYS / RADIO FREQUENCY REMOTE CONTROLS Doors are locked and unlocked using Door locking/unlocking remote control unit A. Press remote control for approximately It is supplied with power by a battery one second (indicator light 2 comes on) which must be replaced when the bat- to lock or unlock the doors.
Page 10
– If you need to replace a key it will not opened within approximately be necessary to take the vehicle 30 seconds of the door being unlocked and all its keys to your RENAULT by remote control, the doors will lock Dealer in order to initialise the again automatically.
OPENING THE DOORS Opening manually from the Opening manually from the Childproof locks outside inside To make it impossible for the rear doors to be opened from the inside, move Front: use the key to unlock front door Pull handle 4. lever 5 on each door and check from lock 2.
LOCKING THE DOORS Doors and tailgate status indicator light The indicator light on switch 2 informs you of the closure status of the doors and tailgate: – the indicator light is on when the doors/tailgate are locked; – the indicator light goes out when a door or the tailgate is open (or incor- rectly closed).
Page 13
1 for about five seconds, check that the doors and tailgate are until a beep is heard. properly closed. If they are properly closed, contact your RENAULT Dealer. To deactivate Also make sure that locking has not With the ignition on, press central door been deactivated inadvertently.
If the vehicle does not recognise the ig- to the engine immobiliser nition key code, tell-tale light 1 will flash (computer, wiring, etc.) may continuously and the engine cannot be be dangerous. It must be started. carried out by a qualified RENAULT technician.
Page 15
ENGINE IMMOBILISER (continued) In all cases, it is essential to consult a RENAULT Dealer as only he is qualified to repair the engine immobiliser. If the coded ignition key is faulty, use the second key (supplied with the ve- hicle).
FRONT HEADRESTS Headrest with tab 1 To remove the headrest Press button 2 and lift the headrest to To raise the headrest release it. Slide it upwards to the required height. To refit the headrest To lower the headrest Insert the headrest rods into the holes, The headrest is important Move tab 1 forwards and lower the with the notches facing forwards.
Page 17
FRONT HEADRESTS (continued) Headrest with tab 3 To remove the headrest First incline the seatback towards the To raise or lower the headrest rear. Pull the headrest towards you (i.e. to- Raise the headrest until it is at the high- wards the front of the vehicle) and slide est possible setting.
REAR HEADRESTS Storage position To adjust the height Simply slide it up. When the headrest is fully lowered, it is in the storage position: do not use To remove the headrest this position when someone is sitting in the rear seats. Press tab 1.
FRONT SEATS We would advise you not to recline the seatbacks too far to ensure that the effec- tiveness of the seat belts is not reduced. Make sure that the seatbacks are locked in place correctly. Nothing should be placed on the floor (area in front of driver) as such objects may slide under the pedal during braking manoeuvres, thus...
Page 20
FRONT SEATS (continued) ð Access to the rear seats Heated seats (three-door versions) With the ignition switched on, Lift lever 5 and slide the seat forwards. press the switch located on the rail cov- er 6. An indicator light will light up on To return the seat to its original (stored) the instrument panel.
SEAT BELTS Adjusting your driving Always wear your seat belt when trav- elling in your vehicle. You must also position comply with the legislation of the par- – Sit well back in your seat (having ticular country you are in. first removed your coat or jacket).
3 cm unwinds; – then allow the seat belt to rewind au- tomatically; – unwind it again; – if there is still a problem, contact your RENAULT Dealer. ç Seat belt reminder warning light Adjusting the front seat belt...
Page 23
– To avoid incorrect triggering of the pending on the level of impact force: system which may cause injury, – protection is provided by the seat only qualified RENAULT Network belt only; personnel may work on the pre- – the pretensioner is triggered to tensioner and air bag system.
Page 24
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (continued) Force limiter Air bags for driver and front passenger Above a certain level of impact force, this mechanism is used to limit the force An “Air bag” marking on the steering of the belt against the body so that it is wheel and dashboard and a label on at an acceptable level.
Page 25
It is not recommended to let a passen- switched on. ger use this seat. If a severe frontal impact occurs, the air Contact your RENAULT Dealer as soon bag(s) inflate(s) rapidly, cushioning the as possible. impact of the driver’s head and chest against the steering wheel and the front passenger’s head against the dash-...
Page 26
– When selling or lending the vehicle, inform the user of these points and hand over this driver’s handbook with the vehicle; – When scrapping your vehicle, contact your RENAULT Dealer for disposal of the gas generator(s). 1.19...
Page 27
– The steering wheel must not be removed (except by qualified personnel from the RENAULT Network). – When driving, do not sit too close to the steering wheel. Sit with your arms slightly bent (see the information on “Adjusting your driving position” in Section 1).
These air bags operate deployed. through slits in the front – Only qualified RENAULT network seatbacks (door side): personnel may remove or modify never insert any objects in a seat.
REAR SEAT BELTS Rear side seat belts 1 Rear centre belt The belts are locked, unlocked and Unwind belt 2 slowly from its housing. adjusted in the same way as the front Click buckle 4 into the black catch 6. belts.
Page 30
REAR SEAT BELTS (continued) Systems in addition to the rear seat belts: Force limiter Above a certain level of impact force to the front, this mechanism is used to limit the force of the belt against the body so that it is at an acceptable level. Special note concerning vehicles with a two-part rear bench seat If you have to fold down the part of the...
Page 31
– No modification may be made to the component parts of the restraint system (belts and seats and their mountings) fitted originally. Contact your RENAULT Dealer for special operations (e.g. fitting child seats). – Do not use any devices which give any play in the belts (clothes pegs, clips, for example).
Refer to the “Child safety equipment valent to one ton: you will find it im- booklet” available from the RENAULT Network to choose the seat suited to possible to hold the child, even if your child and recommended for your you are wearing a belt yourself.
Page 33
CHILD SAFETY (continued) Seats suitable for fitting a child seat Weight of Type of child seat Seat size (2) the child Front passenger Rear side Rear centre seat (1) seats seat Carrycot fitted across the vehicle U - IL < 10 kg F - G Approved for group 0 (3) (4)
Page 34
IUF : Seat allowing a forward-facing child seat with “Universal” approval to be fitted with ISOFIX fixings; check that it can be fitted correctly. IL : Seat allowing a forward facing child seat with “Semi-universal” or “Specific to RENAULT vehicles” approval to be fitted with ISOFIX fixings; check that it can be fitted correctly.
To avoid any risk to your safety, we recommend that you use RENAULT approved accessories because they are designed for your vehicle and are the only accessories for which RENAULT will provide a warranty.
Page 36
CHILD SAFETY (continued) A booster seat with a height-adjustable seatback and a belt guide are recom- mended as this will allow the belt to be worn as close to the base of the neck as possible but not on it. Place the back of the child seat firmly against the vehicle seatback.
Page 37
Your vehicle is also provided with an on the seat runners and the seatback ECE 14 and ECE 16 and allows all child additional ring specific to RENAULT for must be in an upright position. seats approved as “Semi-universal” or securing the belt of those rear-facing “Universal”...
Page 38
CHILD SAFETY (continued) Fitting a child seat (continued) – slide the seat catches 3 in the guides 2 and push the seat firmly to lock it on the rings; – check that the seat is locked cor- rectly by moving it from left to right and then forwards and backwards.
Page 39
CHILD SAFETY (continued) A forward-facing Isofix seat Mounting ring for a forward- A rear-facing Isofix seat fitted fitted on the rear side seat facing seat on the rear side seat When a forward-facing child seat is Use belt 4 supplied with the seat: When a rear-facing child seat is in- installed, the front seat must not be stalled, the front seat must not be...
Page 40
CHILD SAFETY (continued) CHILD SAFETY – No modifications may be made to the component parts of the restraint system (belts, seats and their mountings) originally fitted. – Carefully follow the instructions for fitting provided by the manufacturer of the restraint system. –...
DRIVER’S POSITION, LEFT-HAND DRIVE (continued) The presence of equipment DEPENDS ON THE VERSION AND VEHICLE OPTIONS AS WELL AS THE COUNTRY. 1 Side window demister outlet. 9 Display: 20 Handbrake. – clock and temperature, 2 Side air vent. – radio, clock and temperature, 21 Gear lever.
Page 44
DRIVER’S POSITION, RIGHT-HAND DRIVE (continued) The presence of equipment DEPENDS ON THE VERSION AND VEHICLE OPTIONS AS WELL AS THE COUNTRY. 1 Side window demister outlet. 10 Radio remote control. 19 Heated rear screen switch. 2 Side air vent. 11 – Steering column stalk for wind- 20 Hazard warning lights switch.
Page 45
If it does not light up when the ignition is switched on or if it flashes, there is a Dipped beam headlight tell- fault in the system. tale light Contact your RENAULT Dealer as soon Front fog light tell-tale light as possible. ã Not used...
Page 46
ú Warning light – If it lights up continuously, consult your RENAULT Dealer as soon as This lights up when the engine is started possible. and goes out after a few seconds. – If it flashes, reduce the engine speed It can light up with other indicator lights until the light stops flashing.
Page 47
Contact a RENAULT Dealer. electronic fault, or the presence of Ú Battery charge warning light water in the diesel filter. Anti-lock braking warning Contact your RENAULT Dealer as light soon as possible. It should go out as soon as the engine starts. ù...
Page 48
ï “Proactive automatic transmis- in the system. Indicates that you need to change gear sion” and “Quickshift gearbox” Contact a RENAULT Dealer as soon as in section 2. possible. LPG or CNG mode operating tell-tale This light comes on when the ignition is switched on and goes out within 3 sec- onds.
Page 49
INSTRUMENT PANEL: displays and indicators Rev counter 1 (graduations × 100) Fuel gauge 2 Speedometer 4 (mph or km/h) Coolant temperature indicator 3 Overspeed buzzer Æ Depending on the vehicle, a buzzer This is not serious unless the sounds for approximately 10 seconds warning light comes on.
Page 50
INSTRUMENT PANEL: displays and indicators (continued) Engine oil level low warning 6 The display informs the driver that the engine oil level is low when the engine is started. This warning lasts for 30 sec- onds. Refer to the information on the “Engine oil level”...
TRIP COMPUTER AND WARNING SYSTEM Display selection key 3 For the first few miles after pressing the reset key you will notice: Press button 3 repeatedly to scroll – that the range increases as you through the following information: travel. This is normal, as average fuel a) total mileage recorder, consumption may decrease when: b) trip mileage recorder,...
Page 52
TRIP COMPUTER AND WARNING SYSTEM (continued) The display on the instrument panel of the information described below depends on the vehicle equipment and coun- try. Examples of display selections by repeatedly Interpreting the display pressing 3 a) Total mileage recorder. b) Trip mileage recorder.
Page 53
TRIP COMPUTER AND WARNING SYSTEM (continued) Examples of display selections by repeatedly Interpreting the display pressing 3 e) Current fuel consumption (in mpg or litres/100 km) This value is displayed after reaching a speed of 15 mph (25 km/h). f) Estimated range with remaining fuel (in miles or km) This range takes into account the average fuel consumption since the last time the reset button was pressed.
Page 54
CLOCK - EXTERNAL TEMPERATURE If the electrical supply is cut (battery disconnected, broken supply wire, etc.), the clock will lose its time set- ting. The clock must be reset. For your safety, we recommend that you do not adjust the clock while driving.
REAR VIEW MIRRORS Door mirrors with manual Door mirrors with electrical adjustment adjustment: To adjust the mirror, move lever 1. With the ignition on, move button 2: The door mirror on the driv- – position C to adjust the left-hand er’s side has two clearly de- door mirror;...
REAR VIEW MIRRORS STEERING WHEEL (continued) Interior rear-view mirror Adjusting the steering wheel Its position can be adjusted. When driv- On certain vehicles, the position of the ing at night, to avoid being dazzled by steering wheel is adjustable. the headlights of the vehicle behind, Raise lever 2 and place the steering depress the little lever 1 located behind wheel in the required position;...
EXTERIOR LIGHTING AND SIGNALS á Main beam headlights When the dipped beam headlights are lit, move stalk 1 towards you (an indica- tor light on the instrument panel lights up). To return to the dipped beam headlight position, pull the stalk towards you. Switching off the lights Return stalk 1 to its original position.
EXTERIOR LIGHTING AND SIGNALS (continued) The front and rear fog lights switch off when the exterior lights are switched off. Special case The front and rear fog lights do not op- erate in automatic mode. They only come on when the end of the stalk is in position Lights-on warning buzzer A warning buzzer will sound when a...
ELECTRIC BEAM HEIGHT ADJUSTMENT Versions Setting positions of control A All versions except utility vehicles Position 0 or 1: Basic setting, luggage compartment empty with driver only or with one front passenger. Position 2 or 3: Vehicle with 5 persons on board, luggage compartment empty.
AUDIBLE AND VISUAL SIGNALS é Horn Hazard warning lights Direction indicators Press on the central cushion of steer- Move stalk 1 parallel to the steering ing wheel 2. wheel and in the direction you are going Press switch 3. to turn it. This switch lights up all four indicators Headlight flasher When driving on the motorway, the...
Page 61
WINDSCREEN WASH/WIPE Automatic selection of wiping speed When driving, with a wiping speed se- lected, the wiping speed changes to a lower speed if the vehicle stops: – from fast wiping speed, the speed will change to normal wiping speed; –...
Page 62
WINDSCREEN WASH/WIPE (continued) – Headlights on Press for longer than one second to activate the windscreen washer and headlight washer simultaneously. Windscreen washer, headlight washers With the ignition on, pull stalk 1 towards you. A brief press triggers one sweep cycle In frosty weather, make sure that of the wiper, while a longer press trig- the wiper blades are not stuck by ice...
REAR SCREEN WASH/WIPE DE-ICING Heated rear screen With the engine running, press button 2 (the indicator light on the instrument panel lights up). This function demists the rear screen and the electric door mirrors (if these are fitted to the vehicle). The demist function is stopped in two ways: –...
Fuel filler cap: this is spe- cific to the vehicle type. If you have to replace it, make sure the new cap is of the same type. Contact your RENAULT Dealer. Never place the cap near a source of heat or flame.
Page 65
No modifications what- soever are permitted on any part of the fuel supply system (computers, wiring, fuel circuit, injector, protection covers, etc.) as this may be danger- ous (such work must be undertaken by qualified RENAULT Network per- sonnel). 1.58...
Page 66
Section 2: Driving (Advice on use relating to fuel economy and the environment) Running in - Ignition switch ............Starting/stopping the engine .
RUNNING IN IGNITION SWITCH Petrol version “Ignition on” position M The ignition is switched on: For the first 600 miles (1, 000 km), do not exceed 78 mph (130 km/h) in the – petrol version: the engine may be highest gear or 3,000 to 3,500 rpm. started.
STARTING/STOPPING THE ENGINE Starting the engine Stopping the engine Petrol injection With the engine idling, turn the key back to the “Stop” position. Engine warm or cold – Run the starter without depress- ing the accelerator pedal, – Release the key as soon as the engine starts.
RENAULT Dealer. – using leaded petrol, These faults may be avoided by regularly – using fuel or lubrication addi- taking your vehicle to your RENAULT tives which are not approved by Dealer at the intervals specified in your RENAULT. Maintenance Service Booklet.
However, if after a few seconds and several attempts the engine fails to start, contact a RENAULT Dealer. Do not park the vehicle or run the engine in locations where combustible sub-...
Page 71
(e.g.: deformation of the the ignition on. rear axle). To avoid any risk of accident, have your vehicle checked by a RENAULT Never switch off the igni- Dealer. tion when travelling down- hill, and avoid doing so in normal driving (assistance is not provided).
HANDBRAKE To apply Pull upwards, check that the vehicle is properly immobilised. To release Pull the lever up slightly, press button 1 and then lower the lever to the floor. The red warning light on the instrument panel will light up if you are driving with an incorrectly released handbrake.
Contact Have your vehicle checked and ad- your RENAULT Dealer for this infor- justed by your RENAULT Dealer in ac- mation. cordance with the instructions in the ve- – idling speed: this does not require hicle’s Maintenance Service booklet.
Page 74
– if it comes on continuously, consult – Drive carefully for the first few miles accelerator pedal. your RENAULT Dealer as soon as until the engine reaches its normal possible; operating temperature, rather than –...
Page 75
ADVICE: Antipollution, fuel economy and driving (continued) – In vehicles with air conditioning, it is normal to observe an increase in fuel consumption (especially in urban conditions) when it is used. For vehi- cles fitted with manual air condition- ing, switch off the system when it is not required.
ENVIRONMENT Your vehicle has been designed with In addition to this, your vehicle meets respect for the environment in mind. the requirements laid down in European legislation relating to environmental – Most versions are equipped with a protection. particle filter system including a cat- alytic converter, an oxygen sensor Make your contribution towards pro- and an active carbon filter (the...
(such as driv- out the ABS system. Contact a of the ground, weather conditions and ing at a safe distance from the vehicle RENAULT Dealer as soon as pos- your reactions. The Anti-lock Braking in front). The fact that the vehicle’s sible.
CRUISE CONTROL - SPEED LIMITER: limiter function Î Controls Indicator light The speed limiter function helps you stay within the driving speed limit that 1 Main “On/Off” switch you choose. This orange warning light on the instru- 2 Limit speed storage and increase This may be useful, for example, driving ment panel comes on to indicate that switch...
Page 79
CRUISE CONTROL - SPEED LIMITER: limiter function (continued) Driving When a limit speed has been memo- rised, if this speed is not reached the vehicle behaves in a similar way to a vehicle without the speed limiter func- tion. Once this speed is reached, no effort on the accelerator pedal will allow you to exceed the programmed speed except in an emergency (refer to information...
Page 80
CRUISE CONTROL - SPEED LIMITER: limiter function (continued) Exceeding the limit speed In the event of an emergency It is possible to exceed the limit speed at any moment. To do this: depress the accelerator pedal firmly and fully (beyond the kickdown point). The speed flashes on the instrument panel (trip computer) to inform you that the limit speed is being exceeded.
Page 81
CRUISE CONTROL - SPEED LIMITER: cruise control function Controls 1 Main “On/Off” switch 2 Cruising speed storage and activa- tion. Increasing the cruising speed 3 Stored cruising speed recall 4 Switching the function off (with cruis- ing speed storage) 5 Cruising speed storage and activa- tion.
Page 82
CRUISE CONTROL - SPEED LIMITER: cruise control function (continued) Driving Once a cruising speed is memorised and the cruise control function is active, you may lift your foot off the accelera- tor pedal. Important: you are never- theless advised to keep your feet close to the pedals in order to react if neces- Switching on...
Page 83
CRUISE CONTROL - SPEED LIMITER: cruise control function (continued) Exceeding the cruising speed In the event of an emergency The cruising speed may be exceeded at any time by depressing the accelera- tor pedal. The cruising speed flashes on the in- strument panel (trip computer) to inform you that it is being exceeded.
Page 84
CRUISE CONTROL - SPEED LIMITER: cruise control function (continued) Recalling the cruising speed Switching off the function Press the main “On/Off” switch 1. If you If a speed has been memorised, it is do this, the speed is not memorised. possible to recall it by pressing button 3 on condition that you are driving ap- The instrument panel indicator light...
Page 85
PROACTIVE AUTOMATIC GEARBOX For safety reasons, certain positions may not be selected until the mecha- nism is unlocked: press button A. Only engage D or R when the vehi- cle is stopped, with your foot on the brake and the accelerator pedal re- leased.
Page 86
PROACTIVE AUTOMATIC GEARBOX (continued) Moving off forwards – In hilly or mountainous areas: if you cannot remain in 4 gear be- Select position D. In the majority of cause of the road surface and the traffic conditions, you will not have to number of bends, we would advise touch the gear selector lever again: the you to select D3 (by pressing but-...
N while chanically locked by the driveshaft. the vehicle is stationary. Contact a Apply the handbrake. RENAULT Dealer as soon as possi- ble. Operating faults – If a vehicle with an automatic gear- box breaks down, refer to the infor- –...
QUICKSHIFT 5 GEARBOX Operation Switch on the ignition. The display on the instrument panel switches on. If neutral N is displayed, start the engine but do not depress the acceler- ator pedal. If a gear other than neutral N is dis- played, the display will flash;...
Page 89
QUICKSHIFT 5 GEARBOX (continued) Starting Reverse Moving off forwards (in neutral). The Vehicle stationary display indicates gears N and A. – Brake pedal depressed. Push the – With the brake pedal depressed, selector lever towards the right and push the selector lever forwards then to the rear as shown on the knob and release it.
Page 90
(e.g. when in a traffic jam), – or quickly, if you release the brake and accelerate. The oil level in the automatic gearbox system reservoir is variable depending on use. Adding oil is strictly forbid- den (except by qualified RENAULT Network personnel). 2.25...
Page 91
QUICKSHIFT 5 GEARBOX (continued) Operation in semiautomatic The system does not accept downshifts The vehicle will move off again: which would generate a high engine mode (manual) – either slowly, if you release the brake speed or upshifts which would cause without accelerating (e.g.
QUICKSHIFT 5 GEARBOX (continued) Accelerating and overtaking Parking Driving on slippery surfaces (mud, snow etc.) You have two options: It is possible to park in gear (for exam- ple, on a slope). To do this: When the vehicle is being driven on –...
Page 93
However, you – switch on the ignition; should consult a RENAULT Dealer as In this case, an intermittent beep- – select neutral; soon as possible. ing sound will remind you that you –...
Section 3: Your comfort Air vents ..............Heating and air conditioning system .
Page 95
AIR VENTS (air outlets) 1 left-hand side window demister 5 control panel outlet 6 right-hand side air vent 2 left-hand side air vent 7 right-hand side window demister 3 windscreen demister outlets outlet 4 centre air vents 8 footwell heater outlets for front and rear passengers (depending on the vehicle)
AIR VENTS (continued) Side air vents Centre air vents Air flow Air flow Move control knob 2 (beyond the point Move the control knob 4 (beyond the of resistance). point of resistance). ■ : maximum air flow. ■ : maximum air flow. –...
Page 97
HEATING/VENTILATION Distribution of air in the passenger compartment Move control B. Position All the air flow is directed to the dash- board vents. This selection is not appropriate if all the air vents are closed. Position The air flow is directed towards the dashboard vents and the footwells.
Page 98
HEATING/VENTILATION (continued) Adjusting the amount of air blown into the passenger compartment Move control C from 0 to 4. The passenger compartment is ven- tilated by blown air. The blower deter- mines how much air enters but vehicle speed has a slight effect on this. The further the control is positioned to the right, the greater the amount of air blown into the passenger compart-...
Page 99
AIR CONDITIONING Adjusting the air temperature Move control A. To the right: maximum possible tem- perature. To the left: minimum possible tempera- ture. Adjusting the amount of air blown into the passenger compartment Move control G from 0 to 4. The passenger compartment is ven- tilated by blown air.
Page 100
AIR CONDITIONING (continued) Position The air flow is distributed be- tween all the air vents, the front side window demisting vents, the wind- screen demisting vents and the foot- wells. Position Close the dashboard vents for more effective demisting. All the air is then directed to the wind- screen and front side window demister outlets.
Page 101
AIR CONDITIONING (continued) Passenger Air recirculation allows the de- sired temperature to be achieved as compartment isolation quickly as possible. Button E This starts or stops air recirculation. Normal operation of the heating and Operating tell-tale F lights up when the ventilation system is obtained using air function is operational.
Page 102
AIR CONDITIONING (continued) Note: The air conditioning may be used in all conditions but does not operate when the external temperature is low. – Button B not activated (indicator light C off) The air conditioning is not operating. The settings are the same as a vehi- cle without air conditioning.
Page 103
If they are not, switch off the heating and air con- ditioning system (indicator light C goes out) and contact a RENAULT Dealer. In very hot weather or when the vehicle When the air conditioning system is op-...
AUTOMATIC CLIMATE CONTROL Information and advice for use: refer to the end of the “Automatic cli- mate control” paragraph. The controls 5 automatic windscreen demister/ de-icer button 1 automatic mode operation key 6 air recycling button 2 and 12 air temperature adjustment keys 8 to 10 air distribution buttons 3 display...
Page 105
AUTOMATIC CLIMATE CONTROL (continued) Air conditioning (automatic Operation of the automatic mode mode) Press button 1: the operating tell-tale light comes on. The automatic climate control system guarantees comfort in the passen- Choose a temperature level between 16 ger compartment and good visibility and 26°C by pressing buttons 2 or 12.
Page 106
AUTOMATIC CLIMATE CONTROL (continued) For optimum operation, we recommend that you leave the air vents open in all weathers. Operation of climate control The value on the display 3 indicates the (continued) comfort level. To reach and maintain the selected When the vehicle is started in cold or temperature level, the system acts hot weather, increasing or decreas-...
Page 107
AUTOMATIC CLIMATE CONTROL (continued) Press button 1 to return to automatic mode. Press button 5 again to switch off automatic windscreen demisting/de- icing mode. Visibility (automatic de-icing - This system quickly demists and de- ices the windscreen and the front side demisting) windows.
Page 108
AUTOMATIC CLIMATE CONTROL (continued) Adjusting automatic mode The system normally operates in au- tomatic mode but you can alter the standard settings used by the system (amount of air, etc.). Choice of air distribution You can exit automatic mode by press- ing one of the following keys.
Page 109
AUTOMATIC CLIMATE CONTROL (continued) Varying the ventilation speed In automatic mode, the system uses the most suitable amount of air to reach and maintain the desired comfort level. Automatic mode is switched off by pressing button 4 or 7. The indicator light on button 1 will go out.
Page 110
AUTOMATIC CLIMATE CONTROL (continued) Special features Switching on air recirculation automati- cally switches on the air conditioning. The function operates periodically if the external temperature is lower than ap- proximately 10°C; the indicator light on button 6 will go out after a few minutes. The function operates permanently if the external temperature is above ap- proximately 10°C;...
Page 111
AUTOMATIC CLIMATE CONTROL (continued) Stopping the system mode isolates the passen- Press button 13 ger compartment from the outside at- mosphere. The operating tell-tale comes on. There is no longer any information on dis- Press button 1 or 5 to return to auto- play 3.
Operating faults Fuel consumption As a general rule, contact your You will normally notice an increase RENAULT Dealer in the event of an in fuel consumption (especially operating fault. when driving in town) when the air – Reduction in de-icing, demist- conditioning is operating.
INTERIOR LIGHTING Automatic operation of interior light- ing (depending on the vehicle) – if the doors are unlocked using the remote control, the interior lights are switched on for approximately 15 seconds; – if the doors are locked using the remote control, the lights are switched off immediately;...
Page 114
INTERIOR LIGHTING (continued) Front door lights 4 Rear lights 6 These work in the same way as the When switch 5 is pressed: courtesy light. – continuous lighting, – or intermittent lighting is obtained by opening one of the four doors. It only goes out when the doors are correctly closed, –...
ELECTRIC WINDOWS With the ignition on: – Press the switch for the window concerned to lower it to the desired height; – lift the switch for the window con- cerned to raise it to the desired height. From the driver’s seat From the front passenger seat Operate the switches as follows:...
ELECTRIC WINDOWS /MANUAL WINDOWS (continued) From the rear seats Using switch 6 Manual window winders Press switch 4 or 5. Switch 6 is used from the driver’s seat Turn handle 7. to prevent the rear windows being opened. Passenger safety The driver can inhibit operation of the rear electric windows by pressing switch 6 on the side with the icon.
SUN VISOR Front sun visor Courtesy mirrors 2 Lower sun visor 1. Depending on the vehicle, the sun visors are fitted with a vanity mirror con- cealed behind a cover 3. Courtesy mirror with light If fitted to the sun visors, lift cover 3, the lighting comes on automatically.
GRAB HANDLE WINDSCREEN Grab handle 1 Heat reflecting windscreen This offers support and can be held This windscreen reflects the sun and when the vehicle is moving. limits the infrared rays entering the pas- Do not use it for getting into or out of senger compartment.
MANUAL SUNROOF Closing Hold tab 2 pressed in and return the handle 1 to the initial position. Opening Removing the sunroof Open the sunroof to the first position. To the first position Press button 4 (using a tool such as a Push handle 1 towards the front of the flat-blade screwdriver, if necessary) to vehicle until it stops.
ELECTRIC SUNROOF To slide the sunroof Tilted sunroof, – Opening: tilt the switch 1 backwards and keep it pressed until the required tilt angle is obtained. – Closing: tilt the switch 1 forwards. To tilt the sunroof Driver’s responsibility With the ignition on: Never leave a child (or pet) unattended in the ve- –...
Page 121
ELECTRIC SUNROOF (continued) Sunroof blind Slide it using tab 2. Insert the hook in the sunroof frame to keep the blind closed. – Ensure that the sunroof is prop- erly closed before you leave your vehicle. – Clean the seal every three months using products selected by our Technical Department.
PASSENGER COMPARTMENT STORAGE/FITTINGS Passenger side glove box 1 Central storage Depending on the vehicle, this storage compartment is ventilated and air con- compartment 4 To open, lift catch 2. The box contains ditioned in the same way as the pas- a sunglasses holder, a pen holder and senger compartment.
Page 123
PASSENGER COMPARTMENT STORAGE/FITTINGS (continued) Driver’s storage Door pockets 6 Rear storage compartment 7 compartment 5 Nothing should be placed on the floor (area in front of driver) as such objects may slide under the pedal during braking manoeuvres, thus obstruct- ing its use.
Page 124
PASSENGER COMPARTMENT STORAGE/FITTINGS (continued) Front seat storage pocket 8 Storage compartment under CD changer 10 passenger seat 9 Under the driver’s seat. 3.31...
PASSENGER COMPARTMENT STORAGE/FITTINGS (continued) Navigation system 13 CD-Rom drive. To gain access to the drive, remove cover 14. 11 screen 12 controls. Refer to the operating instructions for information on how to use this equipment. Please keep these instructions with the rest of the vehicle documenta- tion.
ASHTRAY - CIGAR LIGHTER Cigar lighter With the ignition on, push in cigar light- er 2. It will spring back with a click when it is ready. Pull it out to use. After use, re- place it without pushing it all the way Ashtray To open, lift cover 1.
REAR BENCH SEAT (functions) To fold down the seatback Removing the seat base The seat base and the seatback may be folded down (one or both sections) Remove the rear headrest (if fitted). Raise the seat base so as to remove to allow bulky objects to be carried.
LUGGAGE COMPARTMENT For versions with electric central door locking The tailgate is locked and unlocked at the same time as the doors. To open To close Depending on the vehicle, insert the ig- Pull down the tailgate using handle 3 nition key into lock 1 and turn it to the inside the tailgate to assist you.
LUGGAGE COMPARTMENT (continued) Rear parcel shelf Built in garment case 2 Lift the rear parcel shelf slightly and pull it towards you. To remove, unhook the two straps 1. This is located under the rear parcel To refit it, proceed in the reverse order shelf to removal.
Page 130
LUGGAGE COMPARTMENT COVER: utility versions The luggage cover consists of three – The luggage cover is in a semi-folded – The luggage cover is removed. rigid sections. position. To remove the luggage compartment It can be used in one of three ways: cover, place it in the semi-folded po- sition, take hold of the end and pull it –...
TRANSPORTING OBJECTS IN THE LUGGAGE COMPARTMENT Always position the objects trans- ported so that the largest surface is against: – The back of the rear bench seat, for normal loading. – The folded down seat, for maxi- Always position the heavi- mum loading.
BONNET Closing the bonnet To close the bonnet, replace stay 4 back into its holder 3, hold the bonnet in the middle and lower it to 20 cm above the closed position, then release it. It will latch automatically under its own weight.
However, on the trip computer. contact your RENAULT Dealer if more The squares which appear on the dis- than 0.5 litres is being consumed every play indicate the level. These symbols...
Page 135
When working in the engine compartment, ensure that the windscreen wiper stalk is in the park position. Consult your RENAULT Dealer at once if you notice an abnormal or Risk of injury. repeated drop in any of the fluid levels.
Page 136
ENGINE OIL LEVEL (continued) Topping up/filling – Unscrew cap 1; – top up the level (as a guide, the ca- The vehicle must be parked on level pacity between the minimum and ground and the engine should be cold maximum reading on the dipstick 2 (for instance, before the engine is is between 1.5 and 2 litres, depend- started up for the first time in the day).
Page 137
ENGINE OIL LEVEL (continued) Special features Topping up/filling – Unscrew cap 1; of 1.2 16V engines – top up the level (as a guide, the ca- The vehicle must be parked on level pacity between the minimum and ground and the engine should be cold To unclip the dipstick, lever it by hand maximum reading on the dipstick 2 (for instance, before the engine is...
Engine oil change: if you as the engine cooling fan are changing the oil when may start to operate at any Consult your RENAULT Dealer at the engine is hot, be careful moment without warning. once if you notice an abnormal or...
MIN warning line. If you wish to check the disc and drum wear yourself, you should obtain the document explaining the checking pro- cedure from the RENAULT network or from the manufacturer’s web site. Filling After any operation on the hydraulic cir- cuit, a specialist must replace the fluid.
Page 140
(very severe damage is likely to be caused to the engine if it runs out of coolant). If topping up is required, only use prod- ucts approved by RENAULT’s Technical Department: – Anti-freeze protection – Anti-corrosion protection of the cool- ing system.
For topping up or refilling with oil, use Ensure that naked flames, red hot Take care when working in products approved by RENAULT’s objects and sparks do not come into the engine compartment Technical Department. contact with the battery as there is a as the engine cooling fan risk of explosion.
Maintenance Service Booklet for your vehicle. Windscreen washer reservoir Filling: via cap 1. Consult your RENAULT Dealer at This reservoir also supplies the head- once if you notice an abnormal drop light washers (if the vehicle is equipped in any of the fluid levels.
BODYWORK MAINTENANCE Protection against the effects What you should not do – Degrease or clean mechanical com- ponents (eg. the engine compart- of corrosive agents – Wash the vehicle in bright sunlight or ment), underneath the body, parts freezing temperatures. Although your vehicle has been treated with hinges (eg.
Page 144
– mud in the wheel arches and un- derneath the body which forms damp patches. We have selected special products to care for your vehicle and you can obtain these from RENAULT acces- sory outlets. 4.13...
Use products selected by our water) containing: ment inside the passenger compart- Technical Department (RENAULT ment: use of such equipment could accessory outlets) or warm soapy – normal soap, impair the correct functioning of the water and a sponge and dry off with –...
EMERGENCY SPARE WHEEL Emergency spare wheel 2 – Unscrew nut 3. – Remove the tool kit 4. This is located in the luggage compart- ment. – Remove the emergency spare wheel 2. To access the emergency spare wheel: – Open the tailgate. –...
TOOL KIT Jack 4 When refitting the jack, fold it com- pletely and replace it in its location. Wheelbrace 5 Wheelbrace 6 This is used to tighten or release the wheel bolts. Hubcap tool 2 Tool kit 1 is located in the emergency spare wheel.
WHEEL TRIM – WHEELS Wheel trim with concealed Central wheel trim wheel bolts (e.g.: wheel trim 4) (e.g.: wheel trim 1) Remove it using the hubcap tool (in the glove box) by inserting tool 5 into re- Remove it using a hubcap tool 3 (stored cess 6.
CHANGING A WHEEL Insert the wheelbrace hook 2 into the jack 3 and turn a few times to lift the wheel off the ground: Remove the bolts. Take off the wheel. Fit the emergency spare wheel on the central hub and turn it to locate the mounting holes in the wheel and the hub.
TYRES (continued) Tyre pressures Fitting new tyres Pressures should be checked when the tyres are cold; ignore higher pressures Tyre pressures must be adhered to (re- which may be reached in hot weather member to check the emergency spare or following a fast journey. For safety reasons, this op- wheel at the same time).
Page 153
Only certain chains can be fitted to tyres. Contact your RENAULT In all cases, we would recommend Dealer. that you contact your RENAULT Dealer, who will be able to advise you on the choice of equipment that is most suitable for your vehicle.
WINDSCREEN WIPER BLADES Refitting a front or rear wiper blade To refit the wiper blade, proceed in re- verse order of removal. Make sure that the blade is correctly locked in posi- tion. Replacing windscreen wiper Replacing rear screen wiper blades 1 blade 5 –...
HEADLIGHTS WITH HALOGEN BULBS: changing bulbs To comply with local legislation, or as a precaution, you can obtain an emer- gency kit from your RENAULT Dealer containing a set of spare bulbs and fuses. Dipped beam headlights Vehicles with limited accessibility to bulbs (it is sometimes necessary Remove cover B.
Page 156
HEADLIGHTS WITH HALOGEN BULBS: changing bulbs ( continued) Cleaning the headlights As the headlights are made of plastic glass, use a soft cloth or cotton wool to clean them. If this does not clean them properly, use a soft cloth (or cotton wool) slightly moistened with soapy water and then wipe clean with a soft damp cloth or cotton wool.
Page 157
XENON HEADLIGHTS: changing bulbs Main beam headlights Special case for vehicles with re- duced accessibility to the bulbs: contact your RENAULT Dealer. Remove cover A. Turn the connector 1 a quarter of a turn and remove the bulb. Type of bulb: anti-UV (see box).
Special case for vehicles with re- As the headlights are made of plastic duced accessibility to the bulbs: glass, use a soft cloth or cotton wool to contact your RENAULT Dealer. clean them. Remove cover A. If this does not clean them properly,...
Page 159
Contact your RENAULT Dealer. Any operation on (or modi- fication to) the electrical system must be performed by a RENAULT Dealer since incorrect connections could damage the electrical equipment (harness, units and, in particular, the alterna- tor). In addition, your Dealer has available all the parts necessary for fitting these units.
REAR LIGHTS: changing bulbs Remove screw 1 and detach the rear Unclip the bulb holder using tabs 2. 3 Fog light (or nothing) light cluster from the outside. Pear-shaped, bayonet type P 21 W bulb. 4 Indicator Orange pear-shaped, bayonet type PY 21 W bulb.
Unclip the lens 3 from the bulb holder to gain access to the bulb. It consists of a special light bar. For Release bulb holder 2 (using a tool Bulb type: 5 W festoon type bulb. any operation, consult your RENAULT such as a flat-blade screwdriver). Dealer. 5.16...
Page 162
INDICATOR LIGHTS: changing bulbs Unclip the indicator light 1 (using a flat- Turn bulb holder 2 a quarter of a turn blade screwdriver or similar). and take out the bulb. Bulb type: W 5 W. 5.17...
INTERIOR LIGHTS: changing bulbs Courtesy light Rear lights 4 Rotate bulb holder 3 or 2 a quarter of a turn. Unclip cover 1 (using a flat-blade screw- Unclip light (using a flat-blade screw- Bulb type: W 5 W or for single courtesy driver or similar).
INTERIOR LIGHTS: changing bulbs (continued) Door lights 5 Luggage compartment light 6 Press tab 7 to release the lens and access bulb 8. Unclip light 5 (using a flat-blade screw- Unclip light 6 by pressing the tabs on Bulb type: 7 W festoon type bulb. driver or similar).
Page 165
The battery must be kept clean and – When charging, stop the charger creased nominal capacity. Contact your dry. before connecting or disconnecting RENAULT Dealer. Have the battery’s charge status the battery. If your vehicle is to be left stationary checked regularly: –...
Page 166
Start the engine as you would normally. Obtain suitable jump leads (with a large As soon as it is running, disconnect cross section) from a RENAULT Dealer leads A and B in the reverse order or, if you already have jump leads, (4-3-2-1).
Slide the cover on remote control unit 1. Batteries can be obtained from your RENAULT Dealer. These batteries should have a service life of approx- Do not throw away your imately two years. used batteries; give them to...
(risk of fire) in the event of an item of equipment using an excessive amount of current. In accordance with local legislation or as a precautionary measure: Obtain an emergency kit containing a set of spare bulbs and fuses from your RENAULT Dealer. 5.23...
Page 169
FUSES (continued) Allocation of fuses (the presence of fuses depends on the vehicle equipment level). Symbol Allocation Symbol Allocation Symbol Allocation Passenger compartment Å Air bag/Delay timer unit ô Left-hand side light ß Brake lights Right-hand main beam Right-hand side light headlight Heated rear screen Left-hand main beam...
Rear towing point 5 indirectly. lations which apply in the country in which you are driving: do not exceed the towing weight for your vehicle. Contact your RENAULT Dealer. When the engine is stopped, steering and braking assist- ance are not operational. 5.25...
Page 171
Neutral position, and for a distance not exceed- ing 30 miles (50 km). – RENAULT recommends The gear lever must be in position N the use of a rigid towing bar. (neutral).
Page 172
TOWING: towing equipment A: 662 mm. Permissible nose weight, maxi- mum permissible towing weight braked and unbraked: Refer to the information on “WEIGHTS” in Section 6. Refer to the manufacturer’s instruc- tions for information on how to fit and operate the towing equipment. Please keep these instructions with the rest of the vehicle documenta- tion.
Page 173
FITTING A RADIO Radio location 1 Front speakers Remove the two screws 3 and then take off the protective card to reach the Unclip and remove the cover. The Unclip cover 2 using a flat-blade screw- speaker wires. aerial, + and – supply connectors and driver or similar, at the arrows.
Page 174
RENAULT- vehicle: it is advisable only to use approved accessories because they equipment with an external aerial.
OPERATING FAULTS The following advice will enable you to carry out quick, temporary repairs. For safety reasons you should always contact a RENAULT Dealer as soon as possible. The starter is activated CAUSES WHAT TO DO – There is no response, the warning...
Page 176
If the vehicle will not start, do not keep trying to start it. Contact a RENAULT Dealer. Fuel supply cut-off system activated if Contact a RENAULT Dealer. (See the vehicle has been subjected to severe section on the “Fuel cut-off system in impact.
Page 177
“Engine oil level” in Section 4). – at idle speed Low oil pressure. Consult the nearest RENAULT Dealer. – is slow to go out or remains lit on Loss of oil pressure. Stop. Contact a RENAULT Dealer.
Page 178
Coolant pump: belt stretched or broken. Stop the vehicle and switch off the temperature warning light comes on Engine cooling fan not working. engine. Contact a RENAULT Dealer. (or the indicator needle is in the red area). Coolant leaks. Check the condition of hoses and the tightness of the clips.
Page 179
Find the earth wire which is attached to a metallic part, scrape the end of the earth wire and reposition carefully. On both sides: – fuse blown. Replace it. – faulty flasher unit. Needs replacing: Contact a RENAULT Dealer. 5.34...
Page 180
OPERATING FAULTS (continued) Electrical equipment CAUSES WHAT TO DO – The headlights no One only: – blown bulb. Replace the bulb. longer operate. – feed wire disconnected or connector Check and reconnect the wire or the out of position. connector. –...
VEHICLE IDENTIFICATION PLATES Quote the details given on the iden- Vehicle identification plate A 6 Technical specifications of the ve- tification plate A (right-hand side) on hicle. 1 Vehicle type and chassis number. all communication or orders. (The number also appears on the 7 Vehicle paint reference.
Page 184
VEHICLE IDENTIFICATION PLATES (continued) Quote the details given on engine plate B on all communication or orders. Engine plate or engine label B (location varies depending on engine) 1 Engine type 2 Engine suffix 3 Engine number...
Page 185
VEHICLE IDENTIFICATION PLATES (continued) Quote the details given on engine plate B on all communication or orders. Engine plate or engine label B (location varies depending on engine) 1 Engine type 2 Engine suffix 3 Engine number...
Only use the spark plugs specified for your vehicle’s engine. The type should be marked on a label stuck inside the engine compartment. If it is not then contact your RENAULT Dealer. Fitting spark plugs which are not to specification may damage –...
– It is important to comply with the towing weights, governed by local legislation in each country and, in particular, laid down in the Road Traffic Regulations. Contact your RENAULT Dealer about any towing attachments. Under no circumstances may the total train weight (= maximum permissible all-up weight plus weight towed) be exceeded.
– It is important to comply with the towing weights, governed by local legislation in each country and, in particular, laid down in the Road Traffic Regulations. Contact your RENAULT Dealer about any towing attachments. Under no circumstances may the total train weight (= maximum permissible all-up weight plus weight towed) be exceeded.
Page 189
– It is important to comply with the towing weights, governed by local legislation in each country and, in particular, laid down in the Road Traffic Regulations. Contact your RENAULT Dealer about any towing attachments. Under no circumstances may the total train weight (= maximum permissible all-up weight plus weight towed) be exceeded.
Page 190
– It is important to comply with the towing weights, governed by local legislation in each country and, in particular, laid down in the Road Traffic Regulations. Contact your RENAULT Dealer about any towing attachments. Under no circumstances may the total train weight (= maximum permissible all-up weight plus weight towed) be exceeded.
Page 191
– It is important to comply with the towing weights, governed by local legislation in each country and, in particular, laid down in the Road Traffic Regulations. Contact your RENAULT Dealer about any towing attachments. Under no circumstances may the total train weight (= maximum permissible all-up weight plus weight towed) be exceeded.
Page 192
– It is important to comply with the towing weights, governed by local legislation in each country and, in particular, laid down in the Road Traffic Regulations. Contact your RENAULT Dealer about any towing attachments. Under no circumstances may the total train weight (= maximum permissible all-up weight plus weight towed) be exceeded.
Page 193
– It is important to comply with the towing weights, governed by local legislation in each country and, in particular, laid down in the Road Traffic Regulations. Contact your RENAULT Dealer about any towing attachments. Under no circumstances may the total train weight (= maximum permissible all-up weight plus weight towed) be exceeded.
DIMENSIONS (in metres) 0.739 2.471 0.600 1.406 3.811 1.639 1.417 (1) 1.386 (1) Depending on equipment 6.13...
Page 195
SPARE PARTS AND REPAIRS Original RENAULT parts are based on strict specifications and are regularly tested. Therefore, they are of at least the same level of quality as the parts fitted originally. If you always fit genuine RENAULT parts to your vehicle, you will ensure that it performs well. Furthermore, repairs carried out within the RENAULT Network using original parts are guaranteed according to the conditions set out on the reverse of the repair order.
4 SIMPLE ACTIONS* FOR YOUR SAFETY • Always fasten • Always secure children • Adjust the height of • Place heavy objects or your seat belt, using devices suitable the seat belt according luggage at the back of the – even for short journeys for their size and weight to your size.
Need help?
Do you have a question about the Clio 2007 and is the answer not in the manual?
Questions and answers
Key fob not working
To fix a non-working key fob for a 2007 Renault Clio, first check if the battery needs replacing. If replacing the battery does not solve the issue, check that the doors and tailgate are properly closed. If the issue persists, contact a Renault dealer for further assistance.
This answer is automatically generated