Page 1
Service AV7005 / N1B/U1B/K1B f Manual AV Pre Tuner • For purposes of improvement, specifications and design are subject to change without notice. • Please use this service manual with referring to the operating instructions without fail. • Some illustrations using in this service manual are slightly different from the actual set.
Page 2
MARANTZ Parts for your equipment are generally available to our National Marantz Subsidiary or Agent. ORDERING PARTS : Parts can be ordered either by mail or by Fax.. In both cases, the correct part number has to be specifi ed.
SAFETY PRECAUTIONS The following check should be performed for the continued protection of the customer and service technician. LEAKAGE CURRENT CHECK Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check.
Page 4
NOTE FOR SCHEMATIC DIAGRAM WARNING: Parts marked with this symbol z have critical characteristics. Use ONLY replacement parts recommended by the manufacture CAUTION: Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the unit is defective.
Page 5
TECHNICAL SPECIFICATIONS f n Tuner section n Audio Section (for U) –15 [FM](Note: μV at 75 Ω, 0 dBf = 1 x 10 • Analog Receiving Range : Input sensitivity/Input impedance : 200 mV/47 kΩ [FM] 87.5 MHz – 107.9 MHz [AM]530 kHz – 1710 kHz Frequency response : 10 Hz – 100 kHz — +1, –3 dB (DIRECT mode) Usable Sensitivity : S/N : 105 dB (IHF–A weighted, DIRECT mode) Distortion : 0.005 % (20 Hz ~ 20 kHz) (DIRECT mode) [FM]1.5 μV (14.8 dBf) [AM]18 μV Rated output : Unbalanced pre-output: 1.2 V S/N (IHF-A) : Balanced pre-output: 2.4 V [FM]MONO 78 dB...
Please update the following procedure. 1. First, Please update by DFW (33 - 36 page). 2. Next, Please update the latest firmware by DPMS (26 - 32 page). Initializing AV Pre Tuner AV Pre Tuner initialization should be performed when the μcom, peripheral parts of μcom, and Digital P.W.B. are replaced. 1. Turn off the power using ON/STANDBY button. 2. P ress ON/STANDBY button while simultaneously pressing SURROUND MODE and AUTO buttons. 3. C heck that the entire display is flashing with an interval of about 1 second, and release your fingers from the 2 buttons and the microprocessor will be initialized. Note: •If step 3 does not work, start over from step 1. • A ll user settings will be lost and this factory setting will be recovered when this initialization mode. So make sure to memorize your setting for restoring after the initialization. ON/STANDBY AUTO SURROUND MODE Service Jigs When you repair the printing board, you can use the following JIG (Extension cable kit). Please order to marantz Official Service Distributor in your region if necessary. 8U-110084S : EXTENSION UNIT KIT : 1 Set (Refer to "JIG FOR SERVICING".)
Page 7
DISASSEMBLY • Disassemble in order of the arrow of the fi gure of following fl ow. • In the case of the re-assembling, assemble it in order of the reverse of the following fl ow. • In the case of the re-assembling, observe "attention of assembling" it. •...
About the photos used for descriptions in the DISASSEMBLY" section. • The direction from which the photographs used herein were photographed is indicated at "Direction of photograph: ***" at the left of the respective photographs. • Refer to the table below for a description of the direction in which the photos were taken. •...
Page 9
(2) Cut the wire clamp band, then disconnect the connector wires and FFC cable. N1001 STYLE PIN : Loose STYLE PIN : Loose N4201 FFC cable FFC cable b Do not remove the FERRITE CORE when you disconnect the FFC cable. FERRITE CORE...
Page 10
(3) Remove the screws. Direction of Direction of photograph: C photograph: D Please refer to "EXPLODED VIEW" for the disassembly method of each P.W.B included in FRONT PANEL ASSY.
Page 11
2. HEAT SINK ASSY Proceeding : CABINET TOP HEAT SINK ASSY → (1) Remove the screws. View from bottom (2) Cut wire clamp band, then remove the screws. Disconnect the connector wires. Direction of Direction of photograph: C photograph: D N4001 N1001 N4002...
Page 12
(3) Remove the screws. Direction of photograph: A (4) Cut the wire clamp bands, then disconnect the connector wires and FFC cable. Remove the screws, SUPPORT PWB. and the HDMI BRACKET. N1001 STYLE PIN : Loose HEATSINK ASSY STYLE PIN : Loose HDMI BRACKET N4201 SUPPORT P.W.B.
Page 13
(5) Disconnect the connector wires. N4006 N4003 N4004 N4008 N4005 N4009 N8003 Please refer to "EXPLODED VIEW" for the disassembly method of each P.W.B included in HEAT SINK ASSY.
Page 14
3. PCB REG CNT/PCB REG Proceeding : CABINET TOP HEAT SINK ASSY PCB REG CNT/PCB REG → → (1) Remove the screws. N model PCB REG (2) Disconnect the connector wires and connector board. CP102 CP104 REG CNT UNIT N2004 CP13A Direction of photograph: C Board to board...
Page 15
4. HDMI UNIT ASSY Proceeding : CABINET TOP HDMI UNIT ASSY → (1) Remove the screws, then remove the BACK PANEL and the HDMI BRACKET. U model Direction of photograph: A (2) Cut wire clamp band, then disconnect the connector wires and the FFC cables. Remove the screws and the SUPPORT PWB.
Page 16
(3) Cut the wire clamp band, then disconnect the connector wires. Remove the screw. CP13A N2004 N4001 Direction of photograph: C N4002 (4) Disconnect the connector. N4006 N4003 N4004 N4009 Direction of photograph: D N4005 N4610 N4008...
Page 17
(5) Disconnect the connector wire, then remove the screws and the P.W.B HOLDER.. Direction of photograph: D P.W.B. HOLDER CX102 (6) Remove the screws and P.W.B HOLDER. Remove the HDMI UNIT ASSY from the main unit. P.W.B HOLDER View from bottom Please refer to "EXPLODED VIEW"...
Page 18
SPECIAL MODE Special mode setting button b Press the ON/STANDBY button to turn on while pressing both buttons A and B at the same time. Mode Button A Button B Contents Firmware versions such as Main, Sub, DSP are displayed in µcom/DSP Version display mode STATUS RETURN...
Page 19
1. μcom/DSP Version display mode 1.1. Operation specifi cations μcom/DSP version display mode: When started up, the version information is displayed. Starting up: With the "RETURN" and "STATUS" buttons pressed, press the "ON/STANDBY" button to turn the power on. Now, press the "STATUS" button to the display the 2nd item information on the FL Display. 1.2.
Page 20
o OSD Program : Upper O S D P R G : Lower * * * * * * * * * * * * Q0 O SD font data : Upper O S D D A T : Lower * * * * * * * * * * * * Q1 E thernet(DM860) 1st Boot Loader, Hardware ID : Upper...
Page 21
1.3. Error display See the following table for each "Error information" display and its contents (status). Display order is q , w , e , r , t . Condition State State q Sub-μcom NG No response from Sub-μcom S U B E R R O R w DIR NG No response from DIR...
Page 22
2. DUAL BACKUP MEMORY This product has a Dual Backup Memory function. The conventional Backup functions to memorize, in the EEPROM (U5302) in the circuit, a current setting of the moment the main power is turned off so that it can be restored when it is turned ON again.
Page 23
When you repair the printing board, you can use the following JIG (Extension cable kit). Please order to marantz Offi cial Service. Distributor in your region if necessary. Note: When the connection which is wrong in the JIG (EXTENSION UNIT KIT) is done it becomes cause of damage.
Page 24
(3) PCB HDMI is detached from the chassis, and it puts it into the state turned inside out. Please pave an insulation sheet that is larger than PCB HDMI under PCB. b Connect the ground point of PCB to the chassis with a ground lead or the like. PCB INPUT Ground lead PCB VIDEO...
Page 25
PCB SIDE CNT PCV FRONT CNT PCB INPUT Insulation sheet Connection table of Board to Board Ref. No. Ref. No. 11 pin SIDE CNT N4908 HDMI 25 pin SIDE CNT N4907 HDMI 19 pin CP105 FRONT CNT N4910 HDMI 17 pin CP106 FRONT CNT N4911...
ABOUT REPLACE THE MICROPROCESSOR WITH A NEW ONE When replaced of the U-PRO (Microprocessor) or the Flash ROM, confi rm contents of the following. After PWB Name Ref. No. Description Remark replaced HDMI U5301 R5F64169DFD SOFTWARE: Main HDMI U5101 EN29LV160BB-70TIP SOFTWARE: Main ROM HDMI U5500 R5F3650KNFB...
Page 27
--- Cautions on Firmware Update --- ・ In order to use these functions, you must have the correct system requirements and settings for a broadband Internet connection. ・ Do not turn off the power until updating is completed. Even with a broadband connection to the Internet, approximately about 1 hour is required for the updating procedure to be completed.
Page 28
Error Details of Error code Display Coping strategies Code Data acquisition failed (timed out) Check the network connection. C o n n e c t i o n f a i l when downloading Main CPU Carry out the update in an environment fi...
Page 29
Error Details of Error code Display Coping strategies Code Connection to DPMS failed when Check the network connection. S u b * * * m i n rewriting fi rmware such as Sub Carry out the update in an environment C o n n e c t i o n F a i l 5 2 CPU, DSP, FPGA, and PLD.
Page 30
Error Details of Error code Display Coping strategies Code O S D * * * m i n Failure to delete data before Turn the power off then back on. rewriting serial fl ash. Updating starts automatically. U p d a t i n g f a i l Failure to receive fi...
Page 31
Error Details of Error code Display Coping strategies Code Notifi cation of line congestion Check the network connection. E t h e r I M G * * * m i n via DPMS access when rewriting Carry out the update in an environment DM860 related fi...
Page 32
Device display when fi rmware updated Target of devide when fi rmware updated. Target of device Display Error cpde M a i n * * * m i n 10~15 Main 36~3C U p d a t i n g 50~52 S u b * * * m i n...
Page 33
2. How to update by DFW 2.1. Preparations before starting the operation2 (1) Personal Computer (Installed "DFW_0006_AV7005_(Rev.1.0.13)_exe"). (2) RS-232 cable (9P (Male), Straight). 2.2. Connection of the AV receiver (1) Confirm the power on/off switch of the AV receiver is turning off. (2) Connect the RS-232C cable from PC with the AV receiver. RS-232C Cable 2.3. Turn on the AV receiver g Operate the following. Turn on the AV receiver.
Page 34
2.5. Communication check (1) Click the “Check Comm.” button. (2) When connection is good, then you can see the “Communication check OK.” message. (3) If connection is not good, then you can see the “Communication error!” message. Please confi rm the following (a) Check the connection of the AV receiver and PC.
Page 35
2.6. Download the fi rmware (1) Click the "Load" button. (2) Download the fi rmware from the specifi ed download source to PC. 2.7. Complete the fi rmware updating (1) Click the “Update” button. (2) When writing of the fi rmware is completed, the power of this unit turns on automatically and you can see the “Update completed”...
Page 36
(i) In case of laptop PC, Use the AC adaptor. Confi rming the fi rmware’s number after upgraded After completion of the updating operation, the new version number can confi rmed by starting up the AV7005 according to the following procedure.
TROUBLE SHOOTING 1. POWER 1.1. Power not turn on Power not turn on. When the power turned on, does the FLD on the front Is the fuse blown? Refer to 1.2.Fuse is blown. panel light? Check for damage Is a DC 5V voltage output in the SMPS B'D Is a DC 5V voltage being when the cord supplying the...
Page 42
2. Analog video MONITOR OUT (CVBS) output NG Input CVBS Input Function : SAT COMPONENT To A Not output MONITOR OUT (Component) output NG "Video Convert" is set to ON. Input CVBS Input COMPONENT Function : SAT Function : DVD To B...
Page 43
Input CVBS Check power supply voltage. V+5V : N2004-4pin REGULATOR B'D fl aw. V-5V : N2004-1pin Check on set value of each IC. HDMI B'D L4900 : Check I C communication HDMI B'D fl aw. waveforms. L4901 : Check I C communication waveforms.
Page 44
Input CVBS/COMPONENT Check input signal of VIDEO DECODER (U1100). Check signal detection. HDMI B'D HDMI B'D Input CVBS : to A V : L4920 V_L4903 : H(+3.3V) Input COPONENT : to C COMPONENT-Y : L4923 COMPONENT_L4902 : H(+3.3V) COMPONENT-Cb : L4922 COMPONENT-Cr : L4921 Check FRONT CONNECTOR B'D fl...
Page 45
Input COMPONENT Check of power supply voltage V+5V : N2004-4pin REGULATOR B'D fl aw V-5V : N2004-1pin Check on set value of each IC. HDMI B'D L4900 : Check I C communication HDMI B'D fl aw waveforms. L4901 : Check I C communication waveforms.
Page 46
3. HDMI/DVI. 3.1. No picture or sound is output No picture or sound is output. Check HDMI/DVI cable connection. There may be a problem with the HDMI/DVI (1) Is the HDMI/DVI cable properly connected? cable. Check connection. (2) Are you using an HDMI/DVI selector, repeater or a device for Disconnect everything and connect only the improving picture quality? HDMI/DVI cable to check...
Page 47
TV's operating instructions. The TV is defective. (13) Are the picture and sound output when a different TV is used? Check set (AV7005) (14) Is the set's input set to HDMI? Check set's input setting, referring to the Is the output setting of set corresponding to the connection of TV? set's operating instructions.
Page 48
The BD/DVD player does not recognize the connection with the set. (17) Is the "H"(3V-5V) signal outputted of HDMI connector (K1100/K1101/ K1102/K1001/K1002/K1003 : 19pin)? With the BD/DVD player connected, Check voltage of the HDMI The pattern and circuit from the HDMI connector for the input on the side on which the BD/DVD player is connector (K1100/K1101/K1102/K1001/ connected.
Page 49
Check operation of each device. (AMP source : VCR [i/p:OFF, MONITOR OUT: MONITOR1] / Video input of player : 480P / Connect the TV.) Check operation of U1002 (ADV3002). (23) Check power supply. The power supply circuitry is defective. Are 5V or 3.3V supplied to U1002 (each power supply pin)? (24) Check RESET.
Page 50
Check operation of U1601. (30) Check power supply. Is 1.2V supplied to C1632? The power supply circuitry is defective. Is 3.3V supplied to C1656? (31) Check RESET. The RESET circuitry (Q1600 and Is RESET waveform confi rmed in N1601 (1pin), when power is surrounding circuitry) or U1601 is defective.
Page 57
4. AUDIO 4.1. AUDIO CHECK AUDIO OUTPUT : NG INPUT SURROND MODE SOURCE CHECK1 Check ANALOG AUDIO BLOCK. ANALOG 2CH DIRECT ANALOG INPUT SURROND MODE SOURCE CHECK2 Check Digital AUDIO BLOCK. COAX or OPT Legacy(PCM or DolbyDigital or dts…) INPUT SURROND MODE SOURCE CHECK3...
Page 58
4.2. Analog audio No sound is output Is the voltage of ±8V supplied to The power supply of ±8V is repaired. SIDE CNT B'D CP6 13-16 pin? The power supply of ±12VA is Is the voltage of +12V supplied to emitter of Q8003, and voltage of repaired.
Page 59
Checking the settings Set the IP address and other parameters properly. For a fi xed IP setting, check Are the AV7005's network settings correct? whether the IP address is redundant with that of other devices, and check whether the subnet mask setting is correct.
Page 60
Is the USB device compatible with the set? and iPod (Remove some models) are supported. Checking the set (AV7005) Is the wire of N4201 properly connected? Connect the wire properly. Is a voltage (5V) being supplied between pins 1 and 4 of Jack602...
Page 61
5.3. No picture or sound is output Checking the set (AV7005):(If no picture is output) Are video signals output from U4203 pin 27 (Y) and pin 24 (C)? You do not use the USB hub. Check the analog video circuit.
Page 86
INPUT (COMPONENT SIDE) 鉛フリー半田 鉛フリー半田 半田付けには、鉛フリー半田 (Sn-Ag-Cu) を使用してください。 半田付けには、鉛フリー半田 (Sn-Ag-Cu) を使用してください。 Lead-free Solder Lead-free Solder When soldering, use the Lead-free Solder (Sn-Ag-Cu). When soldering, use the Lead-free Solder (Sn-Ag-Cu).
Page 87
INPUT (FOIL SIDE) 鉛フリー半田 半田付けには、鉛フリー半田 (Sn-Ag-Cu) を使用してください。 Lead-free Solder When soldering, use the Lead-free Solder (Sn-Ag-Cu).
Page 88
A.AUDIO (PREOUT) (COMPONENT SIDE) 鉛フリー半田 鉛フリー半田 半田付けには、鉛フリー半田 (Sn-Ag-Cu) を使用してください。 半田付けには、鉛フリー半田 (Sn-Ag-Cu) を使用してください。 Lead-free Solder Lead-free Solder When soldering, use the Lead-free Solder (Sn-Ag-Cu). When soldering, use the Lead-free Solder (Sn-Ag-Cu).
Page 89
A.AUDIO (PREOUT) (FOIL SIDE) 鉛フリー半田 半田付けには、鉛フリー半田 (Sn-Ag-Cu) を使用してください。 Lead-free Solder When soldering, use the Lead-free Solder (Sn-Ag-Cu).
Page 90
1M (5) 1M (5) MTZJ39B MTZJ39B MTZJ39B MTZJ39B MTZJ39B OPEN OPEN OPEN OPEN OPEN OPEN 56K F101 F100 SR7005 SR5005 SR6005 SR7005 AV7005 SR5005 SR6005 AV7005 2A/250V 2A/250V 2A/250V 2A/250V 6.3A/250V 6.3A/250V 6.3A/250V 1.6A/250V 1.6A/250V 1.6A/250V 1.6A/250V 1.6A/250V 3.15A/250V 3.15A/250V 3.15A/250V...
Page 91
1N4007 -8V_IN -8V_IN D144 1N4007 F108 CP104 -8V_IN -8V_IN T1.6AL/250V D140 1N4007 C147 CP101 CN101 100N(EB)-50V *OPTION TABLE SR5005 SR6005/AV7005 SR7005 MODEL AREA OPTION_A NJM2388F05 NJM2388F09 NJM2388F09 NJM2388F09 OPEN NJM2388F09 NJM2388F09 OPEN NJM2388F09 NJM2388F09 NJM2388F09 OPTION_B NOT USE NOT USE...
Page 92
REG_SIRIUS_COMMON CNT 2/4 SIDE CONNECTOR TO RC-5 TO RC-5 PAGE 8(A4) PAGE 8(A1) OPTION A&B MODEL OPTION_B SR5005 SR6005 SR7005 C125Z2-15P C125Z2-19P OPTION_A AV7005 IC109 PQ033DNA1ZPH U ONLY CP802 OPEN 10/50 10/50 M3.3V 232IMO IC1A:A 232OMI AZ4580MTR D/MGND TO HD RADIO...
Page 96
R4328 C4134 TU_GPL02 P_TU_GPL02/TUNED 10/50 L4002 R4323 100K 75J-207CX R4330 OPTION_D C4142 100N-K CHASSIS OPTION_B Q4100 KRC102S MODEL AV7005 SR7005 SR6005 SR5005 Q4101 R4332 AREA KRA111S OPTION A CP4003 OPTION B TUNER_L OPTION C P_TUNERL OPTION D Q4102 P_TUGND TUNER_R...
Page 97
PAGE P_A-7V R4000 D4000 1N4007 C4000 10/50 D4001 1N4007 D4002 1N4007 R4358 R4359 OPEN OPEN R4354 R4001 R4002 R4003 P_PREZ2L. P_PREZ2L C4002 C4001 R4004 R4005 22/50 OPEN 22/50 R4342 OPEN Q4000 Q4001 OPEN KTC2875B IC4008:A OPEN R4010 C4004 10N-K R4012 470K R4013 R4014...
Page 98
PAGE R4154 OPEN R4155 R4157 OPEN R4158 OPEN OPEN R4153 C4065 R4156 C4066 OPEN OPEN OPEN OPEN R4159 OPEN R4160 OPEN Q4052 Q4053 OPEN OPEN R4167 Q4055 R4168 OPEN OPEN OPEN IC4000:A IC4001:A IC4002:A IC4003:A Q4050 OPEN Q4051 OPEN OPEN Q4054 OPEN OPEN...
Page 105
R1059 R1011 OPEN SR7005/AV7005_only SR7005_only K1002 6P-PIN-JACK C1012 10/6.3 IN4CR SR7005,SR6005, SR5005 SR5005 SR5005 SR5005 U(E3) N(E2) K(E1C) F(JP) AV7005 R1060 R1012 X1002 OPEN 17.734M 17.734M OPEN OPEN Q1001 OPEN KRA102S KRA102S OPEN OPEN Q1002 OPEN KRC111S KRC111S OPEN OPEN...
Page 106
TO COMPONENT TO COMPONENT N3003 OPEN CB-G MONITOR CR-G MONIL1 LINE1 MONIL2 LINE2 MONIL3 LINE3 N3001 OPEN CB-G CR-G LINE1 VIN1L1 LINE2 VIN1L2 LINE3 VIN1L3 N3002 OPEN CB-G JAPAN LINEA LINEB ON CHANNEL CR-G Q3001 LINE1 VIN2L1 ASPECT_H OPEN VIDEO-2 LINE2 VIN2L2 LINE3...
Page 107
OPEN OPEN HPDF HPD/HEAC- C21 0.1/10 KRC102S KRC104S DDCDATA DDCCLK UTILITY/HEAC+ CE_Remote 0.1/10 R16 2.2K CKshield R17 OPEN 23P-FFC DOshield TXEN. TXEN. HPDF CE C D1shield DDC_SDA DDC_SCL HDMI5V D2shield CEC5V CEC3.3V OPEN DGND RX_C- RX_C+ RX_0- HDMI BRACKET RX_0+ OPEN RX_1- RX_1+...
Page 111
IPSCL IPSCL IPSDA IPSDA SR7005 only R1806 OPEN R1807 OPEN 1TXINT 1TXINT 1TXRST 1TXRST HDMI_A.SEL MONISEL MONISEL C1816 4.7/6.3 C1817 R1835 OPEN OPEN SR6005 only C1818 OPEN R1836 OPEN L1804 1TXVSYNC OPEN R1802 CEC_CLK SR7005 only 1TXVSYNC 1TXHSYNC 1TXHSYNC DVDD 1TXDE C1801 0.1/10 C1819...
Page 112
U2002 PQ033DNA1ZPH 50mA VOUT ON/OFF GN D DV5V DV3.3V L2000 R2010 DGND U2000 OPEN 10mA OPEN PQ018ENA1ZPH VEI2PCK 110mA VEI2PCK OUT 3 NC 4 VEI2VS VEI2VS VEI2HS VEI2HS VEI2C9 VEI2C9 VEI2C8 VEI2C8 VEI2C7 VEI2C7 VEI2C6 VEI2C6 VEI2C5 VEI2C5 VEI2C4 VEI2C4 VEI2C3 VEI2C3 VEI2C2...
Page 121
TO DM860 C4230 OPEN C4231 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 OPEN R4232 2 3 4 5 6 7 8 9 10 11 12 13 14 15 OPEN SRCMUTE SRCDATA C4232 SRCDATA OPEN SRC64fs...
Page 122
TO MAIN CPU NET3.3V DIGITAL NET1.8V SUPPLY DGND R4410 OPEN R4447 OPEN R4411 OPEN U4404 C4455 C4458 OPEN OPEN OPEN C4459 JTAG N4400 OPEN L4402 OPEN OPEN VSS2 R4431 TCKUSB CVDD MCLKUSB OPEN GND_D1 MCLK TDOUSB BCKoUSB BICK VSS1 R 4433 Aout SDTI OPEN...
Page 124
TO DIGITAL SUPPLY L5028 OPEN SWM5V L5029 OPEN L5030 OPEN REMOTE3.3V L5031 SWM3.3V OPEN M3.3V L5032 OPEN L5033 OPEN L5034 OPEN L5035 N4907 OPEN 25P-SOCKET(C125Z2) L4927 OPEN D5V(MX) SWM5V(MX) SWM3.3V M3.3V DA+5V D/MGND DA+7V SIR_MO5/RDSDA L5005 OPEN SIR_MO/RDS_DATA DA-7V SIR_MI5/RDSCK L5006 OPEN SIR_MI/RDS_CLK...
Page 127
TO HDMI RX TO VIDEO ENCODER TO HDMI TX TO GUI PLD SCPU5V R5527 4.7 K SCPU3.3V R5528 4.7 K DGND R5529 4.7 K SUBBDOWN SUBBDOWN R5530 4.7 K PLDAERR. PLDAERR. MPLDCLK MPLDCLK MPLDDATA MPLDDATA MPLDCSMAIN MPLDCSMAIN SUBTCK DV_POWER1 SUBTMS CEC_POWER SUBTDI SUBTDO...
Page 129
WIRING DIAGRAM AC CORD FRONT WIDE/HIGHT XLR OUT UNIT SIRIUS UNIT UNIT DIGITAL UNIT 23P CARD CABLE (FRONT HDMI) 5P WIRE (DIGITAL PWR) VIDEO UNIT FRONT CNT B'D AUDIO IN UNIT PREOUT UNIT (S4) MAIN TRANS 13P WIRE REG_CNT UNIT (7CH SIGNAL) (S2) REG UNIT...
Page 130
EXPLODED VIEW sfh Hx21 (ONLY U VER.) Bx24 Bx6(ONLY U VER.) 59 x2 Bx12 WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by 26-A the manufacturer. 26-B 印の部分は安全を維持するために重要 な部品です。従って交換時は必ず指定の 部品を使用してください。...
Page 131
422510036205M PLATE JACK BL SR7005 A332 REG UNIT 416510048104M WINDOW DOOR (BL) SR7005 A332 REG-CNT UNIT 402410157000M FRONT PANEL AV7005 (U) A332 FRONT CNT UNIT 402410157017M FRONT PANEL AV7005 (N) A332 N1B,K1B SIDE-CNT UNIT 421410006004M MARANTZ BADGE (AL) FOR M1 MODEL...
Page 133
PACKING VIEW f U model K model N model N model (TOP) 12-A N model N model 12-A U model K model N model (BOTTOM)
Page 134
PACKING CASE AV7005 A332 533610072001M CUSHION F SR7005 A332 533610073004M CUSHION R SR7005 A332 CABINET SHEET CONT LABEL SUB ASSY AV7005 (U) CONT LABEL SUB ASSY AV7005 (N) CONT LABEL SUB ASSY AV7005 (K) ★ 21 LABEL SIRIUS/HD RADIO SR7005 A332 ★ 22...
Page 135
SEMICONDUCTORS Only major semiconductors are shown, general semiconductors etc. are omitted to list. The semiconductor which described a detailed drawing in a schematic diagram are omitted to list. 1. IC's R5F64169DFD (HDMI : U5301) (Note 1) IIO0_0 / IIO1_0 / D8 / P1_0 P4_4 / CS3 / A20 / CTS6 / RTS6 / SS6 AN0_7 / D7 / P0_7 P4_5 / CS2 / A21 / CLK6...
Page 136
R5F64169DFD Terminal Functions Pin Name Synbol I/O Type Pullup STBY stop Function 1 P96/(TXD4) SIRIUS RST O/L SIRIUS control pin 2 P95/(CLK4) HD RADIO RST/ST O/O/I C/C/- O/L HD RADIO control pin /ANALOG TUNER control 3 P94/(CTS4)/TB4IN RC-IN M3VPu O/L Remote control signal input 4 P93/(CTS3)/TB3IN Flasher IN O/L IR Flasher control signal input...
Page 137
Pin Name Synbol I/O Type Pullup STBY stop Function 59 VCC VCC2 60 P131 RST SUB O/L Output for reset of sub-μcom 61 P130 SCPU POWER O/L SUB CPU POWER ON/OFF switch(H:ON) 62 P53/BCLK BCLK O/L External memory access pin(NC) 63 P52/RD O/L External memory access pin(Connection:OE#) 64 P51/(WR1)/BC1...
Page 138
Pin Name Synbol I/O Type Pullup STBY stop Function 123 P157 ZVOL DATA O/L ZONE VOL(NJW1194) control 124 P156 E SPI REQ O/L ETHERNET communication control pin 232C CONTROL 125 P155/(RXD6) O/L SUB LOG MODE : For 232C course switch control (SUB LOG MODE) 126 P154/(TXD6) TUNED...
Page 140
R5F3650KNFB Terminal Functions Pu/Pd PURE Pin Name Synbol I/O Type Det P.OFF Function (Int.) (Ext.) STBY 1 P94 VSEL DATA VIDEO PLD control pin 2 P93 DIR CE DIR control pin (LC89058W-VF4A) 3 P92/SOUT3 DIR DIN DIR control pin (LC89058W-VF4A) 4 P91/SIN3 DIR DOUT DA3.3Pu...
Page 141
Pu/Pd PURE Pin Name Synbol I/O Type Det P.OFF Function (Int.) (Ext.) STBY 58 P32 DAC MDI DAC control pin (ASK4358) 59 P31 DAC MC DAC control pin (ASK4358) 60 VCC +3.3V 61 P30 DAC MS DAC control pin (ASK4358) 62 VSS 63 P27 DAC RST...
Page 143
AD8195ACPZ (HDMI : U1) 30 AVCC PIN 1 29 PE_EN INDICATOR 28 TX_EN 27 AVEE VTTI 26 AVCC AD8195 TOP VIEW 25 AVCC (Not to Scale) 24 AVEE 23 AVCC 22 AVCC AVCC 21 COMP NOTES 1. THE AD8195 LFCSP HAS AN EXPOSED PAD ON THE UNDERSIDE OF THE PACKAGE THAT AIDS IN HEAT DISSIPATION.
Page 147
IS42S32200E6TL Terminl Function Pin No. Signal Pin No. Signal Pin No. Signal Pin No. Signal DATA28 DATA27 IOVDD IOVDD ADDR0 SDCAS IOVDD ADDR2 SDRAS DATA26 ADDR1 SDCKE DATA25 ADDR4 SDWE DATA24 ADDR3 TRST DATA23 ADDR5 SDA10 IOVDD DATA22 SDCLK0 DATA21 IOVDD CLK_CFG0 DATA20...
Page 148
LC89058W-E (HDMI : U2805,U2806,U2807) 35 34 33 32 31 30 29 28 27 26 25 SDIN SLRCK SBCK RDATA XMODE RLRCK DGND LC89058W-E DV DD DV DD DGND GPIO0 RBCK RMCK GPIO1 AGND GPIO2 GPIO3 AV DD RXOUT2 * : Pull-down resistor internal at no selection Pin Functions RXOUT1 RX0-6 input S/PDIF through output pin 1...
Page 149
Pin No. Name Function DGND Digital GND DV DD Digital power supply (3.3V) XMCK Oscillation amplifier clock output pin XOUT Output pin connected to the resonator External clock input pin, connected to the resonator (12.288MHz/24.576MHz) DV DD Digital power supply DGND Digital GND MOUT...
Page 150
ADSP21367KSWZ2A (HDMI : U3200) PIN 1 INDICATOR TOP VIEW (PINS DOWN) ADSP21367KSWZ2A Terminal Function Pin No. Signal Pin No. Signal Pin No. Signal Pin No. Signal DATA28 DATA27 IOVDD IOVDD ADDR0 SDCAS IOVDD ADDR2 SDRAS DATA26 ADDR1 SDCKE DATA25 ADDR4 SDWE DATA24 ADDR3...
Page 152
W9864G2IH-6 Block diagram CLOCK BUFFER CONTROL SIGNAL GENERATOR COMMAND DECODER COLUMN DECODER COLUMN DECODER CELL ARRAY CELL ARRAY BANK #0 BANK #1 MODE REGISTER SENSE AMPLIFIER SENSE AMPLIFIER ADDRESS BUFFER DATA CONTROL CIRCUIT BUFFER DQ31 COLUMN REFRESH COUNTER COUNTER DQM0~3 COLUMN DECODER COLUMN DECODER CELL ARRAY...
Page 153
W9864G2IH-6 Pin description PIN NUMBER PIN NAME FUNCTION DESCRIPTION Multiplexed pins for row and column address. Row address: A0−A10. Column address: A0−A7. 24, 25, 26, 27, 60, 61, 62, Address A0−A10 A10 is sampled during a precharge command to 63, 64, 65, 66 determine if all banks are to be precharged or bank selected by BS0, BS1.
Page 154
EN29LV160BB (HDMI : U3202,U5101) BYTE# DQ15/A-1 DQ14 DQ13 Standa rd DQ12 TSOP RESET# DQ11 RY/BY# DQ10 EN29LV160BB Block Diagram RY/BY# DQ0-DQ15 (A-1) Block Protect Switches Erase V oltage Generato r Input/Output Buffers State Control Program Voltage Generato r Command Chip Enable Regi s ter Data Latch Output Enable...
Page 157
ピン配置 AK4358VQ (HDMI : U3803) LOUT1- AVSS LOUT1+ AVDD VREFH DZF3 ROUT4+ DZF2 AK4358VQ DZF1 ROUT4- CAD0 DIF0 DSDR3 ACKSN Top View DSDL3 BICK DSDR2 MCLK DSDL2 DVDD DSDR1 DVSS DSDL1 AK4358VQ Pin Function Pin Name Function LOUT1- DAC1 Lch Negative Analog Output Pin LOUT1+ DAC1 Lch Positive Analog Output Pin DZF3...
Page 158
DSDL3 DAC3 DSD Lch Data Input Pin DSDR3 DAC3 DSD Rch Data Input Pin DIF0 Audio Data Interface Format 0 Pin ROUT4- DAC4 Rch Negative Analog Output Pin ROUT4+ DAC4 Rch Positive Analog Output Pin VREFH Positive Voltage Reference Input Pin AVDD Analog Power Supply Pin, +4.75 +5.25V AVSS...
Page 159
HY27UF081G2A-TPCB (HDMI : 3901) HY27UF081G2A-TPCB Pin Function Pin Name Description DATA INPUTS/OUTPUTS IO0-IO7 The IO pins allow to input command, address and data and to output data during read / program IO8-IO15(1) operations. The inputs are latched on the rising edge of Write Enable (WE). The I/O buffer float to High-Z when the device is deselected or the outputs are disabled.
Page 161
W9825G6EH-6J (HDMI : U3902) DQ15 DQ14 DQ13 DQ12 DQ11 DQ10 LDQM UDQM A10/AP W9825G6EH-6J Block Diagram CLO CK BUFFER CO NTRO L SIG NAL G ENERATO R CO MMAND DECO DER CO LUMN DECODER COLUMN DECO DER CELL ARRAY CELL ARRAY BANK #1 BANK #0 MO DE...
Page 162
W9825G6EH-6J Pin Description PIN NUMBER PIN NAME FUNCTION DESCRIPTION Multiplexed pins for row and column address. 23 26, 22, A0 A12 Address 29 36 Row address: A0 A12. Column address: A0 A8. Select bank to activate during row address latch time, or 20, 21 BS0, BS1 Bank Select...
Page 165
SA7121 (HDMI : U4203) 33 V SSA2 res. V SSA1 V DDA3 CVBS V SSD1 res. SAA7120 V DDD1 V DDA2 SAA7121 RCV1 res. RCV2 V DDA1 res. MBH790 SA7121 Block Diagram V DDA1, handbook, full pagewidth RCV1 TTXRQ XTALO V DDA2 , V DDA4 V DDA3...
Page 166
SA7121 Pin Description SYMBOL DESCRIPTION − res. reserved test pin; connected to digital ground for normal operation test pin; connected to digital ground for normal operation line-locked clock; this is the 27 MHz master clock for the encoder digital ground 1 SSD1 digital supply voltage 1 DDD1...
Page 173
PARTS LIST OF P.W.B. UNIT f zParts for which "nsp" is indicated on this table cannot be supplied. zThe parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions. Note: The symbols in the column "Remarks" indicate the following destinations. U : North America model N : Europe model K : China model...
Page 178
SPK/SMPS P.W.B UNIT ASSY Ref. No. Part No. Part Name Remarks Q'ty SEMICONDUCTORS GROUP z IC100 00D2623047008 PC123Y22 z IC102 231010091708S TOP258MG IC116 212050010508S KIA2431AP TR100-102 00D2730468907 KTC3199-GR-AT/P D100,101 203050021504S 1N4007 D102 203050021504S 1N4007 D103 203050018706S D25SC6M D104-106 203050021504S 1N4007 D108 203050019501S AP01C-V0...
Page 179
Ref. No. Part No. Part Name Remarks Q'ty C118 CK73B1E104KT +1608 C119 134050107502S CE04W1E470MT(NXA) C120-123 CK73B1E104KT +1608 OTHERS PARTS GROUP BKT10 M3 TAP SIDE TERMINAL CX102 2P BASE(35328) CX105 5P 370mm TJC2508-CKM2509H z F100 652010025001S L=20mm 250V/T2A z F100 652010024008S L=20mm 250V/T1.6A z F101 652010024008S...
Page 180
FRONT P.W.B UNIT ASSY Ref. No. Part No. Part Name Remarks Q'ty SEMICONDUCTORS GROUP D1001 263010045504S BL-BVT201G D1002,1003 00D2760704903 1SR35-400A(T93X) D1004 00D2760760989 MTZJ7.5B T77 D1016 00D2760761975 MTZJ18B T77 D1017 00D2760762903 MTZJ24B T77 D1018-1020 251310004507S CG0603MLC-12LE D1026 00D2760760947 MTZJ5.1B T77 D1027,1028 263010046507S BL-BUF4V5K-1-AV-FP3.5-TBF19.5C D1029,1030...
Need help?
Do you have a question about the AV7005 and is the answer not in the manual?
Questions and answers