Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Arris VAP3400
Summary of Contents for Arris VAP3400
- Page 1 VAP3400/3402 802.11ac Wireless Video Access Point...
-
Page 2: Table Of Contents
©ARRIS Enterprises, Inc. 2014 All rights reserved. No part of this publication may be reproduced in any form or by any means or used to make any derivative work (such as translation, transformation, or adaptation) without written permission from ARRIS Enterprises, Inc. (“ARRIS”). -
Page 3: Installation And Overview
The VAP3400/3402 operates via two (or more) integrated units. You’ll dedicate one unit as the Access Point and the other unit (or units) as its Client. When you connect a VAP to your home gateway, it auto-configures as an Access Point. -
Page 4: About This Manual
This manual provides you with instructions on how to install your VAP3400/3402 video bridge. ARRIS designed the VAP3400/3402 to install and integrate easily with your set-top box and home network. If you encounter any difficulties during the installation process, refer to the Troubleshooting section at the end of this manual. -
Page 5: Front Panel
Solid Cyan = There is an error. Refer to “Troubleshooting” for more details. Off = WPS between Access Point and Client was successful, or two minute time out has occured WPS Button Establishes wireless connection to your home network. VAP3400/3402 802.11ac Wireless Video Access Point • User Guide... -
Page 6: Rear Panels
Ethernet Port Connects to an Ethernet-equipped Gateway, computer, hub, or switch using an RJ-45 cable connection. Power Jack Provides power to the VAP . Power Switch Turns the VAP on or off. VAP3400/3402 802.11ac Wireless Video Access Point • User Guide... -
Page 7: Installing Your Vap3400/3402 (Dual Units)
Connect the power adapter to the VAP , plug the adapter into a wall outlet and set the Power switch to the ON position. You’ll see the Power LED on the unit’s front panel light green, indicating the unit is powered VAP3400/3402 802.11ac Wireless Video Access Point • User Guide... -
Page 8: Step 2: Install The Client
Connect the power adapter to the VAP , plug the adapter into a wall outlet and set the Power switch to the ON position. You’ll see the power LED on the unit’s front panel light green, indicating the unit is powered. VAP3400/3402 802.11ac Wireless Video Access Point • User Guide... - Page 9 Access Point and the Client. Check to ensure the Wireless Link LED lights, indicating the VAP is functioning as a Client. You now can begin streaming video content to your set-top box or boxes. VAP3400/3402 802.11ac Wireless Video Access Point • User Guide...
-
Page 10: Installing Additional Vap Clients
Connect the power adapter to the VAP , plug the adapter into a wall outlet and set the Power switch to the ON position. You’ll see the power LED on the unit’s front panel light green, indicating the unit is powered. VAP3400/3402 802.11ac Wireless Video Access Point • User Guide... - Page 11 Check to ensure the Wireless Link LED lights, indicating the VAP is functioning as a Client. Your VAP is now ready to stream content to the device equipped with the VAP adapter. VAP3400/3402 802.11ac Wireless Video Access Point • User Guide...
-
Page 12: Troubleshooting
WPS button. The LED may continue flashing in a different pattern, rapidly blinking for 1 second and then resting briefly before blinking again. If this occurs, wait one to two minutes and then press the WPS button again. VAP3400/3402 802.11ac Wireless Video Access Point • User Guide... - Page 13 If you cannot establish one of your units as an Access Point, it may indicate that your Access Point gateway is not connected to your service provider’s network. If you experience this problem, contact your service provider for assistance. VAP3400/3402 802.11ac Wireless Video Access Point • User Guide...
-
Page 14: Safety And Compliance
• Comply with all warning and caution statements in the instructions. Observe all warning and caution symbols that are affixed to this equipment. • Comply with all instructions that accompany this equipment. VAP3400/3402 802.11ac Wireless Video Access Point • User Guide... - Page 15 If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: VAP3400/3402 802.11ac Wireless Video Access Point • User Guide...
-
Page 16: Fcc Radiation Exposure Statement
ARRIS Enterprises, Inc., Broadband Communications Sector, 101 Tournament Drive, Horsham, PA 19044, 1-215-323-1000, declares under sole responsibility that the VAP3400/3402 complies with 47 CFR Parts 2 and 15 of the FCC Rules as Class B digital devices. These devices comply with Part 15 of FCC Rules. Operation of these devices is subject to the following two conditions: (1) These devices may not cause harmful interference, and (2) these devices must accept any interference that may cause undesired operation. - Page 17 FCC CERTIFICATION The VAP3400/3402 contains a radio transmitter and accordingly has been certified as compliant with 47 CFR Part 15 of the FCC Rules for intentional radiators. Products that contain a radio transmitter are labeled with an FCC ID and the FCC logo.
- Page 18 (c.-à-d., qu’ils ont la priorité) pour les bandes 5 250-5 350 MHz et 5 650-5 850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. VAP3400/3402 802.11ac Wireless Video Access Point • User Guide...
- Page 19 Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. VAP3400/3402 802.11ac Wireless Video Access Point • User Guide...
- Page 20 ARRIS Enterprises, Inc., 3871 Lakefield Drive, Suwanee, GA 30024 594615-001-a 07/14...
Need help?
Do you have a question about the VAP3400 and is the answer not in the manual?
Questions and answers
A manual was not provided with my cable installation. How do I find out what my password is for the unit?