Advertisement
operators must receive adequate training before using the inverter.
WARNING: When unit is switched off the short-circuit light will come on for 10-15 seconds whilst capacitor discharges. DO NOT open unit until
light goes out.
DO NOT operate the inverter if it or the cables are damaged.
DO NOT use welding cables over 10m in length.
DO NOT attempt to fit any unapproved electrode holder, components, or parts to the inverter unit.
DO NOT connect the return cable to any metallic structure which is not part of the workpiece. This will jeopardise weld quality and may
be dangerous. Exception: Metallic work bench, but connect as near to weld as possible.
DO NOT hit the electrode on the workpiece, this may damage the electrode and make strike-up difficult.
DO NOT get inverter wet or use in damp or wet locations or areas where there is condensation.
DO NOT weld without a welding safety head shield.
DANGER! DO NOT weld near flammable materials - solids, liquids, or gases.
DO NOT weld containers or pipes which have held flammable materials - gases, liquids or solids. Avoid operating on materials cleaned
with chlorinated solvents or near such solvents.
DO NOT pull the inverter by the cables, or the electrode holder.
DO NOT bend, strain or stand on cables.
DO NOT place cables where they will endanger others. long lengths of slack must be gathered and neatly coiled.
DO NOT touch the workpiece close to the weld as it will be very hot. Allow to cool.
DO NOT touch the torch immediately after use. Allow the electrode holder to cool.
DO NOT operate the inverter whilst tired or under the influence of drugs, alcohol or intoxicating medication.
When not in use, store the inverter in a safe, dry, childproof area.
2. DESCRIPTION
2.1.
INTRODUCTION
suitable for ARC welding or for TIG welding (optional) using scratch-start method. Automatic Arc-Force circuitry makes the unit suitable
for TIG welding with a wide variety of rods including rutile, basic and stainless from Ø1.6mm up to Ø3.2mm (MW131) and Ø4mm
(MW151 & MW151PlUs). Includes thermal cut-out and mains voltage leds. Fitted with Hot-start system to counter electrode sticking
during scratch starting. supplied in carry-case with 10mm² arc welding accessory kit (Model No. INVMMA1) for MW131 and 16mm² arc
welding accessory kit (Model No. INVMMA2) for MW151 and MW151PlUs. All models supplied with shoulder strap. Also suitable for TIG
welding with optional TIG accessory kit. MW151PlUs features surge protection, allowing unit to be powered by a generator. Minimum
generator output of 6kW required.
2.2.
DESCRIPTION
These welding machines are a power source for ARC welding, made specifically for direct current (dC). The specific characteristics of
the "INVeRTeR" system provide high speed and precise regulation, ensuring a high quality result for all stick electrode welding.
The "INVeRTeR" system, regulated at the input of the primary mains, also allows for a drastic reduction in the volumes of both the
transformer and the reactance. This reduction in volume and weight enhances the mobility of the machines. The units have power
modules which have been developed on a special printed circuit designed to maximise reliability and reduce maintenance.
2.3.
CIRCUIT SYSTEM DESCRIPTION Refer to fig. 1.
2.3.1. Mains input (single phase), rectifier unit and condenser.
2.3.2. Transistors and drivers switching bridge (IGBT). Turns the mains rectified
voltage into high frequency alternating voltage and permits power regulation
according to the current/voltage of the weld.
2.3.3. High frequency transformer: The primary windings are fed by the voltage
converted by Block 2. It has the function of adapting voltage and current to
the values required by the ARC welding procedure and, simultaneously,
isolates the welding circuit form the mains.
2.3.4. secondary rectifier bridge with inductance. Changes the alternating current
supplied by the secondary windings into direct current.
2.3.5. electronic and regulation board: Instantly checks the value of the welding
current against that selected by the user. It modulates the commands of the
IGBT drivers, which control regulation. The control board also determines the
dynamic response of the current transient during the phases of electrode
fusion (instant short circuit), and is responsible for the safety system.
3. SPECIFICATION
3.1.
SPECIFICATION
Model No. ................................MW131 .................................... MW151 ....................................MW151PlUs
Peak Power: ............................130A ........................................ 150A .........................................150A
output: .....................................10 - 130A ................................. 10 - 150A .................................10 - 150A
duty Cycle: ..............................30% @ 130A ........................... 25% @ 140A ............................25% @ 140A
electrode Capacity: .................Ø1.6 - 3.2mm .......................... Ø1.6 - 4.0mm ...........................Ø1.6 - 4.0mm
Max Absorbed Power: .............3.9kW ...................................... 4.2kW .......................................4.2kW
Mains Voltage: .........................230V - 1PH ............................. 230V - 1PH ..............................230V - 1PH
Insulation Class: ......................F .............................................. F ...............................................F
Protection: ...............................IP21 ......................................... IP21 .........................................IP21
Weight: ....................................4.1kg ....................................... 4.1kg ........................................4.1kg
TIG Accessory Kit: ...................INVTIG1 .................................. INVTIG2 ...................................INVTIG2
Original Language Version
fig.1
fig.2
MW131
MW131, MW151, MW151PlUs
Issue No.1
24/10/11
Advertisement
