70GS-61S SERVICE MANUAL SESG70GS61S00 Issued: 27th March 2001 GA-10 CHASSIS PAL SYSTEM COLOUR TELEVISION MODEL 70GS-61S DE/GG/NL/IT/ITS/CH In the interests of user safety (required by safety regulations in some countries) the set should restored to its original condition and only parts identical to those specified should be used.
Page 2
70GS-61S SERVICE MANUAL UPDATE LOG SHEET Technical Report No. Application Cause / Solution Part No. Page No. Technical Bulletin No. Data /Serial No. Use this page to keep any special servicing information as Technical Report (Bulletin), Technical Information, etc. If only part number changes are required, just change part number directly the part number in the Parts Listing Section.
70GS-61S IMPORTANT SERVICING NOTES Only qualified service personnel are allowed to carry out maintenance and repair of this receiver. SERVICING OF HIGH VOLTAGE SYSTEM AND CRT It is important that the static charge is removed from the high voltage system when carrying out work on the receiver.
70GS-61S CONTROLS & TERMINALS FRONT TV 1. Main Power On/Off Switch 2. Power Indicator / I / II 3. Program Selector (UP/DOWN) 4. Volume Buttons (UP/DOWN) 5. Remote Control Sensor 6. Sound Indicator 7. Remote Control Indicator 8. DOOR Behind the door 9.
70GS-61S ADJUSTMENT PROCEDURES All adjustments to this chassis, except for focus, are carried out in the service mode. • • • • • SERVICE MODE The service mode is provided to enable the engineer to correctly set up the receiver to the CRT fitted in the set.
Page 8
70GS-61S The following geometry adjustments can be carried out. Detailed instructions on how to execute these are given on the following pages Horizontal Vertical • Horizontal Shift • Vertical Amplitude • E-W Width • S Correction • Pin Phase • Vertical Shift •...
Page 9
70GS-61S Corner Symmetry Adjust the Corner Symmetry so that the picture is centred. The effect of this adjustment is shown in figure 7. Note: This adjustment affects to upper and lower sides. • When the volume up button is pressed, side pincushion changes from pincushion to barrel shape.
Page 10
70GS-61S • When the volume down button is pressed the top and bottom scanning decreases and the centre scanning increases. • Press the stand-by button on the remote control to store. Vertical Shift Adjust the Vertical Shift so that the picture is centred.
DO NOT change any NVM data, unless you have been ad- 1. Unable to read or write into NVM: 66% ON, 33% OFF vised to do so by a Sharp representative. If data is incor- twice and OFF for a second.
70GS-61S MOTHER UNIT (F7315N3) PWB COMPONENT LOCATION TABLES. Component Side. Ref No Ref No Ref No Ref No Ref No Ref No (AV) 190754 219710 C386 236982 212090 C803 173228 110490 IC202 221488 35306 J171 155194 98044 J244 178562 54610 (AV).
Page 17
70GS-61S MOTHER UNIT (F7315N3) PWB COMPONENT LOCATION TABLES. Component Side Copper Side Ref No Ref No Ref No Ref No Ref No Ref No 136398 156972 L316 218440 198120 R652 125222 55168 TPC39 165862 102870 C1002 230378 142494 C329 140716...
Page 18
70GS-61S MOTHER UNIT (F7315N3) PWB COMPONENT LOCATION TABLES. Copper Side. Ref No Ref No Ref No Ref No Ref No Ref No C803 173228 110490 IC202 221488 35306 J171 155194 98044 J244 178562 54610 136398 156972 L316 218440 198120 C805...
Page 19
70GS-61S MOTHER UNIT (F7315N3) PWB COMPONENT LOCATION TABLES. Copper Side. Ref No Ref No Ref No Ref No Ref No R1002 233934 128016 R1002 233934 128016 R419 173990 14986 R700 30734 93218 R780 69596 107315 R1003 192278 158750 R1003 192278...
70GS-61S ICs ADITIONAL INFORMATION: TDA9886 (IC201) QUICK REFERENCE DATA SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT supply voltage note 1 4.75 5.00 5.50 supply current −1 dB video at output − µV VIF input signal voltage sensitivity i(VIF)(rms) (RMS value) −...
70GS-61S ICs ADITIONAL INFORMATION: TDA9886 (IC201) SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT −3 dB audio frequency bandwidth for − without de-emphasis; AF(−3dB) dependent on loop filter at pin 4 − weighted signal-to-noise ratio of 27 kHz FM deviation; W(audio) 50 µs de-emphasis;...
Page 24
70GS-61S ICs ADITIONAL INFORMATION: TDA9886 (IC201) PINNING SYMBOL DESCRIPTION SYMBOL DESCRIPTION VIF1 VIF differential input 1 TAGC tuner AGC output VIF2 VIF differential input 2 4 MHz crystal or reference input output 1 (open-collector) VAGC VIF-AGC for capacitor; note 1 FMPLL FM-PLL for loop filter...
Page 25
70GS-61S ICs ADITIONAL INFORMATION: TDA7480 (IC301,IC302) ABSOLUTE MAXIMUM RATINGS Symbol Parameter Value Unit ±20 DC Supply Voltage Storage and Junction Temperature –40 to 150 °C Maximum Voltage Across VFREQ (Pin 9) FREQ Operating Temperature Range -20 to 70 °C ±1.8 Maximum ESD on Pins Rth with "on board"...
Page 26
70GS-61S ICs ADITIONAL INFORMATION: TDA7480 (IC301,IC302) = ±14V; R ELECTRICAL CHARACTERISTICS (Refer to the test circuit, V = 8Ω; R = 50Ω; = 12KΩ; Demod.. filter L = 60µH, C = 470nF; f = 1KHz; T = 25°C unless otherwise specified.)
Page 28
70GS-61S ICs ADITIONAL INFORMATION: MSP3410G (IC303) Absolute Maximum Ratings Symbol Parameter Pin Name Min. Max. Unit − °C Ambient Operating Temperature − −40 °C Storage Temperature −0.3 First Supply Voltage AHVSUP SUP1 −0.3 Second Supply Voltage DVSUP SUP2 −0.3 Third Supply Voltage...
Page 29
70GS-61S ICs ADITIONAL INFORMATION: VCT3811 (IC1001) VCT 38xx Display RGBOUT Processor Video Comb Panorama Video Color Front-end Scaler Back-end Filter Decoder RGBIN Pict.Improv. VOUT VSUPAB GNDAB AOUT MSync Audio Color, Prio VSync C Master 8-bit PWM 24 kB ROM 14-bit PWM...
70GS-61S DESCRIPTION OF SCHEMATIC DIAGRAM NOTE: SAFETY NOTE: 1. The unit of resistance «ohm»is omitted (K=1000 ohms. M= Megaohm). 1. DISCONNECT THE AC PLUG FROM THE AC 2. All resistors are 1/8 watt. unless otherwise noted. OUTLET BEFORE REPLACING PARTS.
Page 32
70GS-61S Red output Green output Blue output E/W Output I Sense V St-by V Switch V Control St-by Vp (Primary) Vertical Input E/W Correction V inner correction Vertical + input H Control...
Page 33
70GS-61S Vb (Horizontal) Vc (Horizontal) V in Headphone L V in Headphone R V in Speaker L V out Speaker L V out Speaker R V in Speker R X1002 V Flyback Vertical Vertical output Vertical input IF Video output...
Page 34
70GS-61S SCHEMATIC DIAGRAM OF MOTHER UNIT (K7315). Page 36 PROT VOUT MUTE PROT HOUT VPROT ALCLOCK...
70GS-61S SCHEMATIC DIAGRAM OF MOTHER UNIT (K7315). Page 37 V OUT V IN VPROT...
Page 36
70GS-61S SCHEMATIC DIAGRAM OF MOTHER UNIT (K7315). PROT HEADR HEADL MUTE STBY HEADR HEADL PROT VOUT...
Page 37
70GS-61S SCHEMATIC DIAGRAM OF MOTHER UNIT (K7315). SC2OUTL R OUT SC2OUTR R IN L OUT L IN AV LINK SC1IN SC2IN V OUT V IN VPROT R OUT R IN SC1INR SC1OUTR L OUT SC1OUTL L IN SC1INL AV LINK...
Page 38
70GS-61S PART LIST 5() 1R 3$576 '(6&5,37,21 &2'( 4 5+7;%0== 757 . 726+,%$ 6 $' REPLACEMENT PARTS 4 &+7;%09 757 5+7; 35()250 6 Replacement parts which have special safety characteristics are identi- 4 &+7;%09 757 5+7; 35()250 6 fied in this manual.
Page 46
70GS-61S PACKING OF THE SET Pack-ad SPAKX4055BMZZ Wrapper SPAKP2006BMZZ FRONT SPAKC5482BMN2 Carton Box Remote Control Batteries RRMCG1071BMSA UBATU0247AJZZ Operation Manual Set...
Page 47
70GS-61S Q601, Q602 REPLACEMENT NOTES: When Q601 or Q602 requires to be replaced, please consider the following steps in order to avoid damaging any part. 1. Gently unclamp clip from side to side using a screwdriver to remove, as shown on Fig.1 2.
Page 48
SHARP ELECTRONICA ESPAÑA S.A. PRINTED BY: TV Division Think Ecology, please use Engineering Dept.