Do you have a question about the SS-15 Series and is the answer not in the manual?
Questions and answers
Skip Harwood
January 25, 2025
Clean light stays on but stops cleaning
1 comments:
Mr. Anderson
February 10, 2025
The clean light stays on because the cleaning cycle was not fully effective at removing buildup. If the light remains on after one cleaning cycle, the manual recommends running a second cycle using a fresh solution of water and vinegar.
Page 1
INSTRUCTION BOOKLET ® ™ Cuisinart Coffee Center SS-15 Series For your safety and continued enjoyment of this product, always read the instruction book carefully before using.
24. Do not operate your appliance in an appliance in any manner. Return appliance to the nearest garage or under a wall cabinet. When storing Cuisinart Repair Center for examination, repair, in an appliance garage always unplug the and electrical or mechanical adjustment.
WARNING: RISK OF FIRE NOTICE OR ELECTRIC SHOCK This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of The lightning flash with arrowhead electric shock, this plug will fit into a polarized outlet only one way.
Charcoal Water Filter ....8 the tap, it won’t taste good in your drink. Cuisinart includes charcoal water filters in 12-Cup Coffeemaker Instructions its water reservoirs to remove chlorine, Setting Up Your 12-Cup Coffeemaker .
12-CUP COFFEEMAKER FEATURES AND BENEFITS Coffeemaker Reservoir Cover Charcoal Water Filter Flips back for easy filling. Eliminates chlorine, bad tastes and odors from tap water. Coffeemaker Water Reservoir (not shown) Adjustable Heater Plate With water level indicator window. Keeps brewed coffee at desired temperature.
GETTING TO KNOW YOUR CONTROL PANEL 12-CUP COFFEEMAKER CONTROLS Detailed programming and use instructions are on pages 8–10. 1. Power Switch (not shown) 7. Function Knob Located on the right side of your brewer. a. PROG Use to turn your Coffeemaker on and off. Select to program Auto On time.
Be sure the PM indicator is on if a PM time is desired. Replacement filters can be purchased in stores, To finish setting the clock, turn the Function by calling Cuisinart Consumer Service, or at knob to any other setting or simply wait until www.cuisinart.com the numbers stop blinking.
SETTING THE AUTO-ON TIME Plug the cord into an electrical outlet. 4. Set preferences When you turn the Function knob to PROG, a. Push the BOLD button if would like a the previously selected Auto On time, or the stronger brew. BOLD button will illuminate. default time (12:00) will flash.
12-CUP COFFEEMAKER 1. Fill the water reservoir to capacity with a mixture of ⁄ white vinegar and ⁄ water. CLEANING AND 2. Press and hold the CLEAN button. When the CLEAN LED indicator flashes, MAINTENANCE the coffeemaker is in Clean mode. Always turn unit off and remove the plug Release the button.
SETTING UP YOUR 6. Place mug on the drip tray. 7. Press the 10 oz. cup button. Light will SINGLE-SERVE flash slowly and the hot water will start to dispense momentarily. COFFEEMAKER 8. The one-time cleaning process is INITIAL CLEANING complete.
2b. Follow brewing instructions on page 11. 2. Cleaning the Funnel – To remove funnel from capsule holder, hold funnel in left hand, twist NOTE: To cancel brewing, simply press the bottom away from you slightly and pull away selected brew size once again and the brewing from capsule holder to remove.
CLEANING THE HOMEBARISTA 4. Discard contents of mug into the sink. REUSABLE FILTER CUP 5. Repeat until ADD WATER light comes on. Simply dispose of coffee grounds, then hand- 6. When descaling is complete, all LED lights wash both the filter cup and filter, or clean on top will be on.
North Glen Harbor Blvd, Glendale, AZ 85307. To This warranty is available to consumers only. facilitate the speed and accuracy of your return, ® You are a consumer if you own a Cuisinart please enclose $10.00 for shipping and handling Coffee Center ™...
Need help?
Do you have a question about the SS-15 Series and is the answer not in the manual?
Questions and answers
Clean light stays on but stops cleaning
The clean light stays on because the cleaning cycle was not fully effective at removing buildup. If the light remains on after one cleaning cycle, the manual recommends running a second cycle using a fresh solution of water and vinegar.
This answer is automatically generated
The clean LED light remains on at all times.