Specifications; Projection Distance; Notes On Use - Panasonic PT-D12000E Brochure & Specs

Specifications

Power supply 220–240 V AC 16–9A, 50Hz/60Hz
Power consumption 1,500 W (15 W in standby mode with fan stopped)
DLP ™ chip Panel size 0.95" diagonal (4:3 aspect ratio)
Display method DLP ™ chip x 3 (R, G, B), DLP
Pixels 1,470,000 (1,400 x 1,050) x 3, total of 4,410,000 pixels
Lens Optional powered zoom/focus lenses
Lamp 300 W UHM™ lamp x 4 (four lamp system)
Screen size 70 - 600 inches,4:3 aspect ratio
(70-300 inches, 4:3 aspect ratio with the ET-D75LE5)
Brightness* 12,000 lumens (four-lamp operation mode)
1
Contrast ratio* 1 5,000:1 (full on/full off, in Dynamic iris 3 mode)
Resolution 1,400 x 1,050 pixels (1,920 x 1,200 pixels compatible, compression mode)
RGB input scanning frequency f 15-100 kHz, fV 24-120 Hz
H
Dot clock 20-162 MHz
Component signal 480i, 480p, 576i, 576p, 720/60p, 720/50p, 1035/60i, 1080/25p, 1080/24p,
1080/24sF, 1080/30p, 1080/60i, 1080/50i, 1080/50p, 1080/60p
Video signal f 15.75/15.63 kHz, fV 50/60Hz
H
(NTSC,NTSC4.43,PAL,PAL60,PAL-N,PAL-M,SECAM)
Lens shift Vertical: ±50% (±40% with the ET-D75LE6) (powered)
Horizontal: ±30% (±20% with the ET-D75LE6) (powered)
Keystone correction range Vertical: ±40° (±22° with the ET-D75LE5, ±28° with the ET-D75LE6),
Using Geometric Adjustment: Vertical ±10°, Horizontal ±15°
Terminals DVI-D IN DVI-D 24-pin x 1, DVI 1.0 compliant, compatible with HDCP, single link
480p, 576p, 1080/60i, 1080/50i, 1080/24p, 1080/24sF, 1080/25p, 1080/30p, 1080/60p, 1080/50p,
720/60p, 720/50p
VGA (640 x 480) – WUXGA*
Dot clock: 25–162 MHz
RGB1/YP P IN BNC x 5
B R
RGB2 IN D-sub HD 15-pin x 1
VIDEO IN BNC x 1, 1.0 Vp-p
VIDEO OUT BNC x 1, 1.0 Vp-p
S-VIDEO IN Mini DIN 4-pin x 1
LAN RJ-45 (10 Base-T/100 Base-TX) x 1, compatible with PJLink™
SERIAL IN D-sub 9-pin female x 2 (RS232C x 1, RS422 x 1)
SERIAL OUT D-sub 9-pin male x 1 (RS422 x 1)
REMOTE 1 IN M3 jack x1 for wired remote control
REMOTE 1 OUT M3 jack x1 for link control
REMOTE 2 IN D-sub 9-pin female x 1 for external control (parallel)
Optional board slot With ET-MD77SD1 SERIAL IN: BNC x 1, SD-SDI signal (YC
installed*
3 SERIAL OUT: BNC x 1, active through
With ET-MD77SD3 SERIAL IN: BNC x 1, SD-SDI signal (YC
installed* 3 Single-link HD-SDI signal (YC
1035/60i, 1080/50i, 1080/60i, 1080/25p, 1080/24p, 1080/24sF, 1080/30p
SERIAL OUT: BNC x 1, active through
With ET-MD100SD4 Link A/Link B IN: BNC x 1 for each, SD-SDI signal (YC
installed Single-link HD-SDI signal (YC
1080/60i, 1080/25p, 1080/24p, 1080/24sF, 1080/30p
Dual-link HD-SDI signal (RGB 4:4:4 12-bit/10-bit): SMPTE 372M compiant: 1920 x 1080/50i,
1920 x 1080/60i, 1920 x 1080/25p, 1920 x 1080/24p, 1920 x 1080/24sF, 1920 x 1080/30p
Dual-link HD-SDI signal (X'Y'Z' 4:4:4 12-bit): 2048 x 1080/24p, 2048 x 1080/24sF

Projection distance

Diagonal
ET-D75LE6
image size
1.0-1.2:1
(aspect raio: 4:3)
min. max.
1,393 mm 1,662 mm
70"
4.6' 5.4'
2,014 mm 2,406 mm
100"
6.7' 7.8'
3,049 mm 3,646 mm
150"
10.0' 11.9'
4,084 mm 4,886 mm
200"
13.5' 16.0'
6,154 mm 7,366 mm
300"
20.2' 24.1'
8,224 mm 9,846 mm
400"
27.0' 32.2'
12,364 mm 14,806 mm
600"
40.6' 48.5'

NOTES ON USE

1. Do not install the projector in locations that are subject to excessive water, humidity, steam, or oily smoke. Doing so may result in fire, malfunction,
or electric shock.
2. The projector uses a high-voltage mercury lamp that contains high internal pressure. This lamp may break, emitting a large sound, or fail to
illuminate, due to impact or extended use.
3. The projector uses of high-wattage lamp that becomes very hot during operation. Please observe the following precautions.
• Never place objects on top of the projector while it is operation.
• Make sure there is an unobstructed space of 500 mm or more around the projector's exhaust openings.
• Do not stack projector units directly on top of one another for the purpose of multiple (stacked) projection.
When stacking projector units, be sure to provide the amount of space indicated between them. These space requirements also apply to
installation where only one projector unit is operating at one time and the other unit is used as a backup.
• If the projector is placed in a box or enclosure, temperature of the air surrounding the projector must be between 0°C and 35°C. Also make sure
the projector's intake and exhaust openings are not blocked. Take particular care to ensure that hot air from the exhaust openings is not sucked
into the intake.
™ projection system
2 (1,920 x 1,200), compatible with non-interlaced signals only,
C 4:2:2 10-bit): SMPTE 259M compliant: 480i, 576i
B R
C 4:2:2 10-bit): SMPTE 259M compliant: 480i, 576i
B R
C 4:2:2 10-bit): SMPTE 292M compiant: 720/50p, 720/60p,
B R
C 4:2:2 10-bit): SMPTE 259M compliant: 480i, 576i
B R
C 4:2:2 10-bit): SMPTE 292M compiant: 720/50p, 720/60p, 1080/50i,
B R
ET-D75LE1 ET-D75LE2
1.5-2.0:1 2.0-3.0:1
min. max. min.
2,072 mm 2,768 mm 2,801 mm
6.9' 9.0' 9.2'
2,992 mm 3,998 mm 4,035 mm
9.9' 13.1' 13.3'
4,526 mm 6,047 mm 6,093 mm
14.8' 19.8' 19.9'
6,060 mm 8,096 mm 8,150 mm
19.9' 26.5' 26.8'
9,128 mm 12,194 mm 12,265 mm
30.0' 40.0' 40.3'
12,196 mm 16,292 mm 16,380 mm
40.1' 53.4' 53.8'
18,332 mm 24,488 mm 24,610 mm
60.2' 80.3' 80.8'
R
Optional board slot With ET-MD77DV
installed
Installation
Power cord length
Dimensions (W x H x D)
Weight*
4
Operating temperature
Operating humidity
Supplied accessories
* Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards.
1
* 2 Only when using VESA CVT-RB(Reduced Blanking) signals.
* 3 The LAN terminal on each board, when mounted, cannot be used because the LAN terminal on the main unit has priority.
* 4 Average value. May differ depending on models.
* The operating temperature range is 0°C (32°F) to 40°C (104°F) when used in High-Altitude mode (1,400 m [4,593 feet] to 2,700 m [8,858 feet]).
5
Also, if the ambient temperature exceeds 40°C (104°F) (35°C [95°F] in High-Altitude mode) when using all four lamps, the light output may be
reduced approximately 30% to protect the projector.
Dimensions
578 (22-3/4")
Throw distance
ET-D75LE3
3.0-5.0:1
max. min. max.
4,215 mm 4,226 mm 7,094 mm
13.8' 13.9' 23.2'
6,067 mm 6,077 mm 10,187 mm
19.9' 20.0' 33.4'
9,153 mm 9,164 mm 1,5341 mm
30.0' 20.2' 50.3'
12,240 mm 12,250 mm 20,496 mm
40.1' 40.2' 67.2'
18,413 mm 18,423 mm 30,805 mm
60.3' 60.5' 101.0'
24,586 mm 24,596 mm 41,114 mm
80.6' 80.7' 134.8'
36,932 mm 36,942 mm 61,732 mm
121.1' 121.2' 202.4'
4. If the projector is to be operated continuously 24 hours a day, use the multi-lamp optical system's alternating lamp operation (lamp changer)
function. The projector can be operated continuously 24 hours a day in four-lamp operation mode, but it will automatically operate with three
lamps for 8 hours of the 24 hours.
5. The lamp replacement cycle duration becomes shorter if the projector is operated repeatedly for short periods.
• The length of time that it takes for the lamp to break or fail to illuminate varies greatly depending on individual lamp characteristics and usage
conditions.
• The brightness of the lamp will gradually decrease with use.
6. Because the ET-D75LE5 is a fixed short-throw lens, the lens shift function cannot be used with it.
7. Due to natural characteristics of lamps, screen brightness may vary (flicker). This is not an indication of faulty lamp performance.
For more information about Panasonic projector ––
Please contact Panasonic or your dealer for a demonstration.
JQA-1617
may be subject to export regulations. UHM is trademark of Matsushita Electric Indusutrial Co., Ltd. VGA and
(C) 2008 Panasonic Projector Systems Company is a Unit of Panasonic Corporation of North America. All rights reserved.
Specifications are the same as those for the DVI-D IN terminal on the main unit.
Front/rear, ceiling/floor
3.0 m (9.9")
578 x 320 x 643 mm (22-3/4" x 12-19/32" x 25-5/16") (without lens)
Approx. 35 kg (77.1 lbs) without lens
0 -45 °C (32 -113 °F)* 5
10-80% (no condensation)
Power cord, Wireless/wired remote control unit,
Batteries for remote control (3V AA battery x2), Eye bolt x4, Wire rope
ET-D75LE4 ET-D75LE8
5.0-8.0:1 7.9-15.0:1
min. max. min.
7,101 mm 11,374 mm 11,091 mm
23.3' 37.3' 36.4'
10,193 mm 16,292 mm 16,009 mm
33.5' 53.4' 52.6'
1,5348 mm 24,488 mm 24,207 mm
50.3' 80.3' 79.4'
20,502 mm 32,685 mm 32,404 mm
67.3' 107.2' 106.3'
30,811 mm 49,078 mm 48,799 mm
101.1' 160.9' 160.1'
41,120 mm 65,471 mm 65,194 mm
134.9' 214.7' 213.9'
61,738 mm 98,257 mm 97,984 mm
202.6' 322.2' 321.4'
http://panasonic.net/pavc/projector
EC98J2010
Weights and dimensions shown are approximate. Specifications are subject to change without notice. This product
XGA are trademarks of International Business Machines Corporation. All other trademarks are the property of their
respective trademark owners. Projection Images simulated.
DLP, DLP logo and DLP Medallion logo are trademarks or registered trademarks of Texas Instruments.
The PJLink trademark is an application trademark in Japan, the United States, and other
(C) 2008 Matsushita Electric Industrial Co,Ltd. All rights reserved.
All information included here is valid as of July 2008.
unit: mm (inch)
ET-D75LE5
0.8:1
max. fixed
21,142 mm 1,022 mm
69.3' 3.3'
30,358 mm 1,496 mm
99.5' 4.9'
45,717 mm 2,286 mm
149.9' 7.5'
61,076 mm 3,076 mm
200.3' 10.0'
91,794 mm 4,656 mm
301.0' 15.2'
122,512 mm
—
401.8'
183,948 mm
—
603.3'
countries and regions or registered trademarks.
PT-D12KE1-08July10K Printed in Japan.