Page 3
OR IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Toshiba shall not be liable for any damages, losses, expenses or costs, if any, incurred in connection with or as a result of use of any information or data provided herein.
Page 4
Increasing attention is given to issues related to the global environmental. Toshiba Corporation recognizes environmental protection as a key management tasks, and is doing its utmost to enhance and improve the quality and scope of its environmental activities. In line with this, Toshiba proactively promotes Green Procurement, and seeks to purchase and use products, parts and materials that have low environmental impacts.
Page 6
Print this page SAFETY INSTRUCTION WARNING: BEFORE SERVICING THIS CHASSIS, READ THE "SAFETY PRECAUTION" AND "PRODUCT SAFETY NOTICE" INSTRUCTIONS BELOW. Safety Precaution WARNING: SERVICING SHOULD NOT BE ATTEMPTED BY ANYONE UNFAMILIAR WITH THE NECESSARY PRECAUTIONS ON THIS RECEIVER. THE FOLLOWING ARE THE NECESSARY PRECAUTIONS TO BE OBSERVED BEFORE SERVICING THIS CHASSIS. 1.
Page 7
7. Parts mounting and routing dressing of wirings should be the same as that used originally. For safety purposes, insulating materials such as isolation tube or tape are sometimes used and printed circuit boards are sometimes mounted floating. Also make sure that wirings is routed and clamped to avoid parts that generate heat and which use high voltage.
Page 8
Resistance values in orms ( ). V: Voltmeter or oscilloscope (r.m.s. or peak reading) Input resistance : Input capacitance : 200 pF Frequency range : 15 Hz to 1 MHz and d.c. respectively Note: Appropriate measures should be taken to obtain the correct value in case of non sinusoidal waveforms. The measuring instrument is calibrated by comparing the frequency factor of with the solid line in figure F.2 of IEC 60990 at various frequencies.
Page 11
Print this page SAFETY INSTRUCTION Handling the LCD Module Safety Precaution In the event that the screen is damaged or the liquid crystal (fluid) leaks, do not breathe in or drink this fluid. Also, never touch this fluid. Such actions could cause toxicity or skin irritation. If this fluid should enter the mouth, rinse the mouth thoroughly with water.
Page 12
2. Carefully align the holes at all four corners of the LCD module with the corresponding holes in the LCD cover and fasten with screws. Do not strongly push on the module because any impact can adversely affect the performance. Also use caution when handling the polarized screen because it can easily be damaged.
Page 13
5. Glass is used in the panel, so do not drop or strike with hard objects. Such actions can damage the panel. 6. CMOS-LSI circuitry is used in the LCD module, so avoid damage due to static electricity. When handling the module, use a wrist ground or anchor ground.
Page 14
liquid crystal due to cold air or loss of resilience or other damage. 9. Do not disassemble the LCD module. Such actions could result in improper operation. 10. When transporting the LCD module, do not use packing containing epoxy resin (amine) or silicon resin (alcohol or oxim). The gas generated by these materials can cause loss of polarity.
Page 20
Print this page MODEL ID and PANEL ID Panel ID in Global Serial No. Total digits Model ID SERIAL Panel ID Max 14 ****** 3 digits 3 digits 6 digits 2digits (A00001~Z99999) Y : Year 2008 2009 2010 2011 2012 ·...
Page 21
WK04 · · · · · · WK53 Model/Panel Information Model Model ID Panel ID Panel 19EL933RB LC185EXE-TEA1 19EL934RB LC185EXE-TEA1 23EL933RK LTM230HT10 23EL934RK LTM230HT10 26EL933B LC260EXN-SDA3 26EL933G LC260EXN-SDA3 26EL933RB LC260EXN-SDA3 26EL934G LC260EXN-SDA3 32EL933B LC320EXN-SEA1 32EL933G LC320EXN-SEA1 32EL933N LC320EXN-SEA1 32EL933RB LC320EXN-SEA1 32EL934G LC320EXN-SEA1 32EL934RB...
Page 23
LTA400HM01-R 40LV933G V400HJ2-L01 LTA400HM01-R 40LV933N V400HJ2-L01 LTA400HM01-R 40LV933RB V400HJ2-L01 Panel vendor Information (Panel ID) Marking Panel Vendor Marking Panel Vendor Marking Panel Vendor SHARP SAMSUNG LPL/LGD When the panel version is updated within the same panel vender, the last digit will be incremented by 1.
Page 25
Print this page DESTINATION SETTING CHANGE Whenever replacing the Main PCB with new one, perform this procedure. 1. IR Key MENU → APPLICATIONS → Sleep Timer → OK. 2. When display _ _ : _ 0 input 4 numbers 2766. The Factory menu will display.
Page 26
3. Move to Tag "3" by Right/Left Arrow key on the Remote. 4. Select "Model Type" cell. 5. Select the appropriate model type by Right/Left Arrow key on the Remote. Model type is written on the rating label.
Page 27
6. Select "Reset to Def". 7. Select "Yes" and press "OK" button on the Remote.
Page 29
Print this page PARTS LIST Precaution WARNING: BEFORE SERVICING THIS CHASSIS, READ THE "SAFETY PRECAUTION" "PRODUCT SAFETY NOTICE". CAUTION: The international hazard symbols " " in the schematic diagram and the parts list designate components which have special characteristics important for safety and should be replaced only with types identical to those in the original circuit or specified in the parts list.
Page 31
Print this page PARTS LIST Updating history Currently there are no updates available. Please check back at a later time for any future updates. Location Parts No. Description E200 75030330 PC BOARD ASSY, MAIN, 9C-EB40M00U0 E250 75030266 PC BOARD ASSY, POWER, 0433-006T000 E270 75030142 IR BOARD ASSY, 90-EB40S02X0 E300A...
Need help?
Do you have a question about the 32AV933N and is the answer not in the manual?
Questions and answers