Sky Navigator User Instructions

user instructions
Introduction
Your Sky Navigator gives you the functionality of both a
control and a keyboard. When the front of the
it will operate as a Sky remote control , and when open it will operate
as a keyboard.
Your is compatible with all
Sky Navigator Sky
Sky +
including . To ensure that your Sky Navigator
work with your equipment, it is very important that you observe the
following instructions. You will need to change the factory setting in
order to enable your Sky Navigator to operate your

Getting started

A
The batteries are already fitted inside your Sky Navigator
them ready for operation, remove the tape from the battery pack by
gently pulling on the tab and withdrawing it from the unit as shown
below.
Next check that the batteries are connected. Press any button on the
unit and check that the red LED at the end of the unit flashes.
Your Sky Navigator is now ready to operate your
Sky +
have a please follow the instructions in section B.
Set up for owners of Sky +
B
Only follow these instructions if you are using your
Sky +
with .
1.
Press tv " " button on the Sky Navigator
2. Press and hold down "Select" and the yellow button together for
about 2 seconds, until the red LED on the
twice.
3. Press "1 "
4.
Press "select", the LED on the Sky Navigator
To reset your Sky Navigator to operate a
steps 1 and 2 and in step 3 press "0"
C Setting up your
your TV
Sky remote
Sky Navigator is closed,
Your Sky Navigator
brand of TV please follow these steps:
digital satellite receivers,
1. Find your TV manufacturer listed in section I, e.g Philips is 0081.
is correctly set up to
Write down your TV code here [
listed, press
Sky + . further assistance.
Turn on your TV.
2.
3. Ensure that the front of your
. To connect
4. Press "tv".
5. Hold down "select" and the red button together for about two
seconds, until the red LED on the
6.
Press "tv" again.
Sky digibox. If you
7. Key in the four digit code for your brand of TV.
The LED on the
illuminates only once, re-check the code for your brand of TV and
start again at step 4.
8.
Press the standby button
switches off, press "select". The LED on the
flash twice. If your TV does not switch off, press "tv", then press the
standby
Repeat this (press "tv", then
then press "select".
Sky Navigator
If you are still experiencing problems, please telephone for technical
assistance. you will find the
pressing "services" and selecting "Telephone Numbers".
Sky Navigator flashes
will flash twice.
Sky digibox carry out
Sky Navigator to operate
will also operate your TV. To set up for your
] [ ] [ ] [ ]. If your TV is not
"interactive" and select "Sky Customer Service" for
Sky Navigator is closed.
Sky Navigator flashes twice.
Sky Navigator will flash twice. If the LED
on your Sky Navigator . If your TV
Sky Navigator
button.
standby ) until your TV turns off,
"Technical Help" telephone number by
D Key operation in Sky remote control
sets your remote to operate your
tv
sets your Sky Navigator to
operate your TV
box office
shows the Box Office
screen
tv guide
shows the TV Guide
screen
tv guide
mute
turns your TV's sound off
+
and on
vol
vol+ and -
-
changes your TV's volume
text
arrows
move the highlight around
the screen to select the
option you want
text
switches to text mode
will
*play / pause
plays or pauses the
programme
pqrs
*rewind
rewinds the programme
*R
records the programme
colour keys
select the corresponding
colour options shown
on-screen
number keys
select channel numbers
or on-screen options
* These functions are only applicable to Sky + .
mode
Sky +
Sky digibox or
standby
turns your set top box
(or TV) on and off
services
tv
shows the Services
screen
interactive
box office services
shows the interactive
interactive
screen
i
i
mute
shows information
+
about the
programme you have
ch
highlighted
-
ch+ and -
back up help changes the channel
select
selects the option you
have highlighted or
confirms your choice
back up
1 2 3 shows the previous
abc def
screen
5 6
4
jkl
ghi mno
help
7 8 9
shows help on using
tuv wxyz
Sky Guide
0
fast forward*
fast forwards the
programme
stop*
stops playback of
the programme