Related Manuals for ARTROMOT K3
Summary of Contents for ARTROMOT K3
- Page 1 ARTROMOT ® Service Manual Up to Serial number 2999...
-
Page 2: Table Of Contents
1. History This service manual is to perform some repairs on ARTROMOT ® -K3 products. Repair and maintenance work 2. Purpose may only be carried out by authorised persons, as other- wise all warranty services and liabilities shall be void. -
Page 3: Assembly And Disassembly
4. Assembly and disassembly Preparations for transport the ARTROMOT ® -K3 has to be done. The first step is to move the device in a maximum position of EXTENSION = -5 degrees. Remove the power adapter and put this part in a separate pad. -
Page 4: Bill Of Material For Service Parts
6. Bill of material for service parts Position Description Order-Number Electronics Power adapter 115V 0.0031.107 Power adapter 115V / 230V 0.0031.107W Hand-held programming unit 0.0032.123 Motor control 0.0031.101 Rubber mat 2.0031.195 Sheet metal cover 2.0031.116 Motor electronics 0.0031.120 Fantype lock washer 799.011 Screw thread slab 962.903... - Page 5 2.15 Exterior slit 2.0032.114 2.16 Bottom plate 2.0032.108 2.17 Attachment plate femur bow 2.0032.101 2.18 Attachment plate femur bow 2.0032.100 2.19 Thread plate 962.901 M6 2.20 Pan head screw DIN912M6x8A2 2.21 Pan head screw DIN7984M5x25A2 2.22 Countersunk screw DIN7991M4x8A2 2.23 Cylinder pin DIN6325D5x10 2.24...
- Page 6 3.28 Spacer sleeve 0.0031.104 3.29 2.0031.188 3.30 Countersunk screw DIN7991M5x20vz 3.31 Screw thread pin DIN916M4x4sw 3.32 Screw thread pin DIN914M4x4sw 3.33 Countersunk screw DIN7991M4x10vz 3.34 Hexagonal nut DIN934M5vz 3.35 Pan head crew DIN912M5x6vz 3.36 Countersunk screw DIN7991M5x25A2 3.37 Countersunk screw DIN7991M5x55vz 3.38 Countersunk screw...
- Page 7 4.18 0.0031.108 4.19 0.0031.105 Knee case Knee case 2.0032.125 Retaining ring DIN471A10x1 Bearing shell 2.0032.122 Washer 2.0032.123 Shim DIN988D10x16x0,1 Knee case 2.0032.119 Knee case (Poti) 2.0032.121 Knee electronics 0.0031.121 Spiral cable for knee case 0.0031.122 5.10 Lid potentiometer 2.0031.189 5.11 Shaft 2.0032.120 5.12...
-
Page 8: How To Perform The Repair
-K3 will stop at EXTENSION / FLEXION = 110 degrees. Attention: It is important to push or pull at the femur bow so that in direction Flexion the ARTROMOT ® reach the mechanical stud. (approximately 3 cm in front of the right/left cover). -
Page 9: Explosion Drawing Part
8. Explosion drawing part 1... - Page 10 9. Explosion drawing part 2...
- Page 11 Adjust a maximum femur length. 7. First press "STOP" and afterwards press "START". The ARTROMOT ® -K3 should then reach both points of changing direction within 50 to 65 seconds. 8. Change the speed to 50% and repeat test 7 The ARTROMOT ®...
- Page 12 Ormed GmbH & Co. KG • Merzhauser Straße 112 • D-79100 Freiburg • Tel. 0761/45 66-01 F a x 0 7 6 1 / 4 5 6 6 5 5 - 0 1 • w w w . o r m e d . d e • e - m a i l : i n f o @ o r m e d . d e St.
Need help?
Do you have a question about the K3 and is the answer not in the manual?
Questions and answers