How to discard a used battery Some FURUNO products have a battery(ies). To see if your product has a battery, see the chapter on Maintenance. Follow the instructions below if a battery is used. Tape the + and - terminals of battery before disposal to prevent fire, heat generation caused by short circuit.
SAFETY INSTRUCTIONS Please review these safety instructions before you operate the equipment. Indicates a condition that can cause death or serious injury WARNING if not avoided. Indicates a condition that can cause minor or moderate CAUTION injury if not avoided. Warning, Caution Prohibitive Action Mandatory Action...
Page 4
SAFETY INSTRUCTIONS WARNING CAUTION The fish finder picture is not Keep units other than the radar refreshed when the picture antenna away from rain and advance setting is “OFF”. water. Do not steer the boat according to Fire or electrical shock can occur if the depth indication in this state, to water gets inside the equipment.
Page 5
Safety Labels malfunction. A safety label is attached to the display unit. Do not remove the label. If the label is missing or damaged, contact a FURUNO agent or dealer about replacement. Name: Warning Label (1) WARNING Type: 86-003-1011-3 To avoid electrical shock, do not remove cover.
TABLE OF CONTENTS FOREWORD ........................xii SYSTEM CONFIGURATION ..................xiv SYSTEM INTRODUCTION ..................1-1 1.1 Controls ........................1-2 1.2 Remote Control Unit (option)..................1-5 1.2.1 Remote Control Unit MCU-002 ..............1-5 1.2.2 Remote Control Unit MCU-004 ..............1-6 1.3 How to Turn the Power On or Off ................1-7 1.4 How to Adjust the Brilliance of the Display and Power Switch and Hue.....1-8 1.5 Home Screen......................1-9 1.6 How to Select a Display....................1-10...
Page 7
TABLE OF CONTENTS 2.7 How to Find the Range and Bearing Between Two Locations........2-8 2.8 Multiple Plotter Displays..................... 2-9 2.9 Cartographic Text and Objects on Vector Charts ............ 2-10 2.9.1 Control visibility of text and object information in vector charts....2-10 2.9.2 Control visibility of cartographic objects in S-52 charts........
Page 8
TABLE OF CONTENTS 4.5 Default Point Settings ....................4-4 4.6 How to Find Number of Points Used ................4-5 4.7 How to Move a Point ....................4-5 4.7.1 How to move a point on the screen..............4-5 4.7.2 How to move a point from the points list ............4-5 4.8 How to Delete a Point....................4-6 4.8.1 How to delete a point on the screen...............4-6...
Page 9
TABLE OF CONTENTS 5.10.7 XTE lines...................... 5-14 5.10.8 Waypoint arrival notification ................. 5-14 5.10.9 End of route notification ................5-14 5.10.10Steering a route with the NAVpilot ............... 5-15 5.11 Routes Menu......................5-16 RADAR........................6-1 6.1 How to Transmit, Set the Radar in Stand-by.............. 6-1 6.2 Tuning ........................
Page 10
TABLE OF CONTENTS 6.25.9 CPA/TCPA alarm ..................6-30 6.25.10CPA graphic display ..................6-31 FISH FINDER (SOUNDER) ...................7-1 7.1 How the Fish Finder Operates..................7-1 7.2 How to Transmit, Go to Stand-by ................7-1 7.3 How to Select a Display....................7-2 7.3.1 Single frequency display ................7-2 7.3.2 Dual frequency display ...................7-3 7.3.3...
Page 11
TABLE OF CONTENTS CAMERA/VIDEO/FUSION-Link................9-1 9.1 How to Display a Video Image ................... 9-1 9.2 Video Signal Type ...................... 9-2 9.3 How to Set the Video Display..................9-2 9.3.1 How to set the video signal ................9-2 9.3.2 How to adjust the image size ................. 9-3 9.3.3 How to switch your video inputs..............
Page 12
TABLE OF CONTENTS 12.9 How to Show or Hide the Target IDs ................12-5 12.10AIS List ........................12-5 12.11When an AIS SART is Received................12-7 12.12CPA/TCPA Alarm ....................12-7 12.13How to Register an AIS or DSC Target to the Buddies List........12-8 12.14CPA Graphic Display ....................12-9 12.15AIS Transponder FA-30, FA-50 ................12-10 12.16DSC Message Information..................12-11 12.16.1DSC distress message notification.............12-11...
FOREWORD A Word to the Owner of the TZTL12F, TZTL15F Congratulations on your choice of the TZTL12F, TZTL15F Multi Function Display, members of the NavNet TZtouch2 family of multi-function displays. We are confident you will see why the FURU- NO name has become synonymous with quality and reliability.
Page 14
FOREWORD • Built in GPS receiver and antenna • Built in fish finder • AIS function (requires connection of AIS transponder) receives AIS data from AIS equipped vessels, shore stations and navigational aids and displays relevant data. ™ • ACCU-FISH provides at-a-glance estimation of length and depth of individual fish.
SC-30 FAX-30 GP-330B FUSION-Link Equipment* FI-5002 FI-50/70 NAVpilot-700 IF-NMEA2K1/2 Multi Function Display* Multi Function Display* IF-NMEAFI TZTL12F TZTL12F Wide Monitor Remote Controller CCD Camera TZTL15F TZTL15F MCU-002 or MCU-004 CCD Camera SD Card Unit SDU-001 Event SW Transducer External Buzzer...
For example, “Tap [Settings] - [General]”. • The colors mentioned in this manual are the default colors. Your colors may be dif- ferent. • Most of the screenshots in this manual are taken from the TZTL12F. Layouts may be slightly different on the TZTL15F.
1. SYSTEM INTRODUCTION Controls The TZTL12F and TZTL15F are operated by a power switch and touch controls. You operate the plotter, radar, fish finder, etc. with • Touch control • pop-up menus and hidden functions, where you select options • Menus, where you select options •...
Page 18
1. SYSTEM INTRODUCTION Touchscreen operations The tables which follow outline the touchscreen operations. Operation with a finger Operation with a finger Function Short tap • Select a menu item. • Select an object or posi- tion to display the corre- sponding pop-up menu.
Page 19
1. SYSTEM INTRODUCTION Notes on touch control operations • Waterdrops on the screen can cause mis-operation and slow touch response. Wipe the screen with a dry cloth to remove the water. • This equipment uses a capacitive touch screen. Tap the screen with your fingertips directly.
(selection cursor) marks current selection in menus. 1.2.1 Remote Control Unit MCU-002 Function STBY•AUTO Switches the steering mode of the FURUNO NAVpilot-700 series Autopilot between the STBY and AUTO modes*. CENTER key • Returns own ship to the center of the screen (Plotter/Weather/Radar display).
1. SYSTEM INTRODUCTION 1.2.2 Remote Control Unit MCU-004 Function STBY•AUTO Switches the steering mode of the FURUNO NAVpilot-700 series Autopilot between the STBY and AUTO modes*. HOME/BRILL • Short push: Opens the home screen. • Long push: Opens the Brilliance/Power win- dow.
1. SYSTEM INTRODUCTION * When you switch the steering mode with the STBY•AUTO key, a beep sounds and then one of the messages shown below appears. The message does not appear on the home screen. STBY modeAUTO mode: "NAVpilot is engaged." AUTO modeSTBY mode: "NAVpilot is disengaged."...
1. SYSTEM INTRODUCTION Note 2: Do not turn off the power during the start-up. Wait until the start-up is complet- ed before you turn off the power. Note 3: The screen refreshes slower in low ambient temperature. How to Adjust the Brilliance of the Display and Power Switch and Hue With the power applied, press to show the [Power &...
1. SYSTEM INTRODUCTION Home Screen The home screen is where you access functions and menus, select displays and check sensor status. Tap the [Home] icon at the top left corner to show the home screen. The home screen is automatically closed, and the previous operation display restored, when no operation is detected for approx.
1. SYSTEM INTRODUCTION Red: Sensor error Gray: Sensor inactive (stopped) The Functions section provide the following features: [MOB]: Enters a MOB mark (to mark man overboard location on the plotter and radar displays). See section 1.17. [Settings]: Menus (general, plotter, radar, sounder, etc.) for customization of the sys- tem.
1. SYSTEM INTRODUCTION 1.6.2 How to select a display from the quick page The quick page, which carries all the display icons set for large size on the home screen, lets you change the display from the current display. To show the quick page, swipe the top of the screen downward. Tap desired display icon to change the display.
1. SYSTEM INTRODUCTION How to Edit the Display Icons The default home screen arrangement provides seven displays (icons) in configura- tions according to the equipment that you have in your network. If the arrangement does not meet your requirements, you can change the display icons to suit your needs.
1. SYSTEM INTRODUCTION 1.7.2 How to edit a display icon Long tap the display icon to edit to show the editing icons on the display icon. Tap the applicable editing icon. Refer to the figure and instructions below. Edit icon content Remove icon Long Change icon size...
1. SYSTEM INTRODUCTION Hidden Functions This equipment has five functions that are normally hidden from view: quick page, slide-out menu, pop-up menu, [Layers] menu, and data area (navdata). Swipe or tap the screen at the locations shown below to access the hidden functions. A function window is automatically erased from the screen when it is not operated within the time specified with [User Interface Auto-Hide] in the [General] - [Settings] menu.
Page 30
1. SYSTEM INTRODUCTION The pop-up menu provide a subset of functions that are relevant to the object or lo- cation tapped. Unavailable functions are greyed out. The [Layers] menu controls the items that are displayed on the top layer of the active display.
1. SYSTEM INTRODUCTION Data Area The data area at the left side of the screen shows various navigation data, in movable and editable data boxes. You can select the data to display, select format (analog or digital) for data and change the order of the data. Data availability depends on your system configuration.
1. SYSTEM INTRODUCTION 1.9.2 How to change the contents of a data box Tap the data box to change, and the [Modify NavData] pop-up menu appears. Tap the data to use, on the pop-up menu. < Tap item to change Tap an item 1.9.3...
1. SYSTEM INTRODUCTION 2. Tap the data to add, on the pop-up menu. For example, tap [Cursor].The added data appears in the data area. 1.9.4 How to delete a data box Tap the data box to delete, then tap [Remove] on the [Modify NavData] pop-up menu. 1-18...
1. SYSTEM INTRODUCTION 1.9.5 How to switch an indication between analog (graphic) and dig- ital Tap the data box for which to switch the indication, and the [Modify NavData] pop-up menu appears. Use the [Graphic] flipswitch to switch between analog and digital indi- cations.
1. SYSTEM INTRODUCTION 1.10 Micro SD Cards This equipment uses two types of micro SD cards, chart and data. The chart cards contain charts and the data cards store plotter-related data such as tracks, routes, points and generic data such as menu settings. (The SD card drive on the multi func- tion display is for chart cards only.
Page 36
1. SYSTEM INTRODUCTION Compatible micro SD cards The table below lists the micro SD cards that have been verified for use with this equip- ment. Maker Model Capacity (GB) Class KINGMAX KM-MCSDXC10X64GUHS1P KM-MCSDHC10X32GUHS1P KM-MCSDHC4X32G KM-MCSDHC10X16GUHS1P KM-MCSDHC4X16G Kingston SDCX10/64GB SDC10/32GB SDC4/32GBS SDC10/16GB SDC4/16GB SDC10/8GB...
1. SYSTEM INTRODUCTION 1.11 Plotter Introduction The plotter provides a small world map in raster format. A vector chart for the US coastline (with Alaska and Hawaii) is provided also. The plotter section has functions to enter points, and create and plan routes. The plotter receives position data fed from the built in GPS receiver.
1. SYSTEM INTRODUCTION 1.12 Radar Introduction A radar system operates in the microwave part of the radio frequency (RF) range. The radar detects the position and movement of objects. Objects are shown on the radar display at their measured distances and bearings in intensities according to echo strength.
1. SYSTEM INTRODUCTION 1.13 Sounder (Fish Finder) Introduction The sounder display provides a picture of the echoes found by the fish finder. Echoes are scrolled across the screen from the right position to the left position. The echoes at the right position are the current echoes. These echoes can be from separate fish, a school of fish, or the bottom.
1. SYSTEM INTRODUCTION 1.14 Settings Menu The [Settings] menu provides the options for customizing your system. The [Settings] menu, as well as all other items on the home screen, is automatically closed, and the previous operation display restored, when no operation is detected for approx. one minute.
Page 41
1. SYSTEM INTRODUCTION • Alphabet, numerical data entry: A menu item that requires entry of alphabet and/or numerical data has a keyboard icon ( ). Tap the keyboard icon to show the keyboard. (The keyboard displayed depends on the item selected. Some items provide only the numeric keyboard.) Enter data, then tap ...
Page 42
1. SYSTEM INTRODUCTION • Color selection: A menu item that requires selection of color shows the current color selection to the right of the name of the menu item. Tap the menu item to show the color options. Tap color option desired. Current selection is highlight- ed with a light blue square.
1. SYSTEM INTRODUCTION 1.15 Function Gesture The function gesture controls what occurs when you tap the screen with two fingers. Select the function as below. 1. Open the home screen, then select [Settings] - [General]. 2. Tap [Function Gesture]. None Screen Capture Event Home...
1. SYSTEM INTRODUCTION 1.16 Language The default interface language is English (United States). To change the language, do as follows: 1. Open the home screen, then tap [Settings] - [General]. 2. Tap [Language]. 3. Tap the language to use. The message "APPLICATION HAS TO RESTART NOW! DO YOU WANT TO RESTART APPLICATION?"...
1. SYSTEM INTRODUCTION 1.17 Man Overboard (MOB) The MOB function is used to mark the location of man overboard, from the plotter and radar displays. At the moment the MOB function is activated, the MOB mark is put at the current position, on both the plotter and radar displays. How to mark the MOB position Tap [MOB] on the home screen.
1. SYSTEM INTRODUCTION 1.18 Wireless LAN Settings You can connect to the internet with the wireless LAN signal to download weather in- ™ formation (see chapter 11) and to connect to an iOS or Android device. To download weather information, connect the existing LAN network. To connect to an iOS or An- ™...
1. SYSTEM INTRODUCTION 7. Turn on [Wireless] to see the available WLAN networks at the bottom of the screen. 8. Tap the desired network to show the network key (password) entry screen. 9. Enter the network key, then tap [OK]. The IP address, security type and signal strength of the WILAN are shown.
Page 48
1. SYSTEM INTRODUCTION ™ 1.19 How to Create a My TimeZero Account, Login ™ to Your My TimeZero Account ™ You will need to create a My TimeZero account to access the cloud and My Friends (social network) functions. Prepare a PC or mobile device to complete the registration. 1.
Page 49
1. SYSTEM INTRODUCTION 5. Click [Get started!] to finish. Your name Your e-mail address 6. From a PC or mobile device, follow the link provided in the e-mail to log into your account. Leave the NavNet TZtouch2 as is. 7. Tap [Go to Log in page] on this equipment. 8.
PLOTTER This chapter shows you how to do the following: • Use and prepare the plotter display • Set plotter related alarms • Control the track Chart Type A world map in raster chart format is included in your unit. A vector chart for the US coastline (Alaska and Hawaii included) is provided also.
2. PLOTTER Display Range You can change the display range to change the amount of information shown. The selected range appears in the box at the bottom left-hand corner of the screen. Range area Range area Display range How to zoom in or out the display range Method 1: Pinch the plotter display.
2. PLOTTER Orientation Mode The chart can be shown in head-up or north-up orientation. Tap the orientation mode switch, [HU] or [NU], whichever is shown, at the bottom left corner to change the ori- entation mode. North Up: North is at the top of the screen. When your heading changes, the boat icon moves according to heading.
2. PLOTTER The Boat Icon 2.5.1 Description The boat icon (red) marks current position and moves according to your vessel’s movement. Heading line Turn direction indicator COG vector • The heading line is a straight line that runs from your position and shows the cur- rent heading.
2. PLOTTER 2.5.3 COG vector length The COG vector shows estimated course and speed of your ship. The tip of the vector is the estimated position of your ship at the end of the selected predictor time or dis- tance (set on the menu). You can increase the length of the predictor to find the esti- mated position of your ship in the future on the current course and speed.
2. PLOTTER 2.5.4 Boat icon orientation You can select the orientation of the boat icon to heading or COG. 1. Open the home screen, then tap [Settings] - [Ship & Track]. 2. Tap [Vessel Icon Orientation]. 3. Tap [Heading] or [COG]. 4.
2. PLOTTER Detailed information Tap an object to show the pop-up menu. Tap [Chart Object info] on the pop-up menu to show detailed information. 2.6.2 Chart information Tap a location on the chart not occupied by a chart object, then tap [Chart Info] on the pop-up menu.
2. PLOTTER How to Find the Range and Bearing Between Two Locations The [Distance] item in the slide-out menu measures the range and bearing between any two locations on your chart. Range and bearing between the two locations are dig- itally indicated on the screen.
2. PLOTTER Multiple Plotter Displays Three plotter displays can be shown on one screen. With three plotter displays, you can see the conditions around your ship on both short and long ranges. Also, you can see how your ship moves toward your destination from more than one angle. For ex- ample, you can show one display in 3D and the other two in 2D.
2. PLOTTER Cartographic Text and Objects on Vector Charts This section shows you how to show or hide the cartographic objects and text infor- mation that appear on the vector charts. 2.9.1 Control visibility of text and object information in vector charts The [Settings] - [Vector Chart] menu controls the visibility of text and object informa- tion, for example, buoy names and light description.
2. PLOTTER [Text (Other)]: Show or hide the other text information. [Display Buoy Names]: Show or hide the buoy names. [Display Light Description]: Show or hide the light descriptions. [Display Light Sectors]: Show or hide light sectors for fixed beacons. [Display Routes]: Show or hide routes.
Page 61
2. PLOTTER [S-52 Vector Chart Display Mode]: Set the level of information to show on the chart. The selections are [Custom], [Base], [Standard], [Other], and [Fishing]. The chart fea- tures are turned on or off according to setting. Note: The following menu items except [Reset Default Settings] are unavailable when you select the mode other than [Custom] [Unknown Object]: Show or hide unknown objects that appear on the chart.
2. PLOTTER 2.10.1 XTE alarm The XTE alarm tells you when your ship goes off course by more than the limit set (XTE alarm boundaries). Starting point Go to point Alarm setting Intended :Alarm area course 1. Turn on [XTE Alarm] in the [Alarm] menu. 2.
2. PLOTTER [Over] or [Under] The [Over] or [Under] alarm sounds when the temperature is over or under the set value, respectively. 1) Tap [Temperature Alarm Value] to display the software keyboard. 2) Set the value, then tap . Go to step 3. [Within] or [Out of] The [Within] or [Out of] alarm sounds when the temperature is within or out of the temperature range set, respectively.
2. PLOTTER 2.10.5 Anchor watch alarm The anchor watch alarm tells you that your ship has moved a distance greater than the set value when the ship must not be moving. Alarm : Alarm area setting Your ship's position where you start the anchor watch alarm.
2. PLOTTER 2.10.8 Alarms list When an alarm is violated, you can see the name of the offending alarm on the [Alarms] list. The list stores both warning and system messages. Open the home screen, then tap [Lists] followed by [Alarms]. Active alarms are flashing and have a red vertical bar at the let margin.
2. PLOTTER 2.11.3 Track recording interval In drawing the track, the position of your ship is stored into the memory of this unit at an interval of time. A shorter interval provides better reconstruction of the track, but the storage time of the track is reduced. 1.
Page 68
2. PLOTTER 5. Tap [Variable Color] then tap an option. [Depth]: Change the color of the track with depth. [SST Range]: Change the color of the track with change in sea surface tempera- ture. [SST Variation]: Change the color of the track according to variation in sea sur- face temperature.
Page 69
2. PLOTTER 6. Tap [Variable Color Setup]. Threshold amount Color icon For [SST Variation] For [SST Range] For [Depth] For [Bottom Discrimination] For [Depth Variation] For [Speed] 7. For [Bottom Discrimination], tap [Mud], [Sand], [Rock] or [Gravel]. For others, tap a color (seven choices).
2. PLOTTER On the screen 1. Tap a section of track to display the pop-up menu. 2. Tap [Color]. 3. Tap a color. 2.11.5 Track thickness You can set the thickness of the track. If you are following the same track many times, you can show the track in the thinnest width to prevent overlapping of track.
2. PLOTTER 2.11.7 How to create a route with track currently being recorded (track back) You can create a route with track that is currently being recorded. This method can be useful for retracing track; for example, when you need to retrieve crab pots or the like. The route is saved to the routes list.
2. PLOTTER 2.11.8 How to delete tracks If the screen becomes full of track, you can not know which is the newer track. Delete the track you do not need. How to delete a specific part of a track You can delete a track partially. Tap the part of a track to delete. Tap [Del From Here] or [Delete Up to Here].
2. PLOTTER 2.12 Plotter Menu This section describes the [Plotter] menu items, which are in the [Settings] - [Plotter] menu. [Grid Interval]: Set the distance between grid lines. The options are [Off] (no lines), [Very Small], [Small], [Medium], [Large], and [Very Large]. [Show Scale Slider]: Show or hide the scale slider.
NAVpilot to steer to a point, see paragraph 4.12.4. The FURUNO NAVpilot-700 Series Auto Pilot installs in the NavNet TZtouch2 network to get automatic steering when going to a point or a route. The following NAVpilot func- tions can be controlled from a NavNet TZtouch2 display: •...
2. PLOTTER 2.13.2 How to show the NAVpilot control box in the data area 1. Tap [DATA] or [ROUTE] on the data area to select where to show the NAVpilot- control box. 2. Tap a data box or an unoccupied area to select where to show the NAVpilot con- trol box.
2. PLOTTER 2.14.2 How to hide or show the ActiveCaptain display On the Plotter display or Weather display, show the [Layers] menu, then turn [Active- Captain] on or off as required. 2.14.3 How to find a marina You can find the location of a marina as follows. 1.
2. PLOTTER 2.14.5 How to update the ActiveCaptain database It is a good idea to keep the ActiveCaptain database up-to-date to ensure that you will always have the latest data. Connect your NavNet TZtouch2 to the WLAN. Login to ActiveCaptain in the [Settings]- [ActiveCaptain] menu.
When the My Friends display is active, the vessels that you have registered (see paragraph 2.15.1) are marked with a symbol, as shown in the figure below. Tap the symbol to show detailed information about the vessel. Furuno N 34°26.400’ E 135°07.104’...
Page 79
2. PLOTTER This page is intentionally left blank. 2-30...
3D DISPLAY, OVERLAYS 3D Display The 3D display has native 3D chart design that allows full time 3D presentation. This true 3D environment gives you all of the information you require with no restrictions on the information you can see. You can plan your routes, enter points, etc. like on the 2D chart.
3. 3D DISPLAY, OVERLAYS 3.1.1 How to activate the 3D display 1. To switch between the 2D and 3D displays, tap the 2D/3D switch at the bottom left corner on the screen or drag upward as shown below. The icon is filled in white when the 3D display is active.
3. 3D DISPLAY, OVERLAYS 3.1.2 How to make the 3D view clearer In the 3D display, some topographical features are easier to see if you use the 3D ex- aggeration feature. This feature expands both objects on the chart and the underwater vertically so that you can easily see the shape of the objects and position.
3. 3D DISPLAY, OVERLAYS Overlays Five overlays are available for the plotter display: depth shading, satellite, radar, tide information, and tidal current. 3.2.1 Depth shading overlay The depth shading overlay shows the depths in different color (the default settings are red (shallow), yellow (medium) and blue (deep)).
Page 84
3. 3D DISPLAY, OVERLAYS Depth shading settings The depth shading settings are in the [Plotter] menu. [Auto Depth Shading Color Scale]: Turn automatic depth shading color scale selec- tion on or off. [Minimum Value]: Set the minimum depth range for which to show depth shading, with the software keyboard.
3. 3D DISPLAY, OVERLAYS 3.2.2 Satellite photo overlay You can put the satellite photo for your area on the 2D and 3D displays. Open the [Layers] menu then turn [Satellite Photo] on or off. High resolution satellite images for the USA coastline are not provided standard, but are available at no cost (except shipping and handling).
Page 86
3. 3D DISPLAY, OVERLAYS How to switch between stand-by and TX; match overlay and radar ranges Tap the [TX] icon at the bottom right corner to set the radar in transmit or stand-by state. The icon is filled in white when the radar is transmitting; blue in stand-by. To match overlay and radar ranges, open the home screen, tap [Settings] - [Plotter], then turn on [Range Link].
3. 3D DISPLAY, OVERLAYS 3.2.4 Tide info overlay Your system carries worldwide tide information, shown with tide icons, which you can overlay on the plotter display. The tide icon ( ) appears at the locations of tidal record- ing stations. How to display the tide info overlay Open the [Layers] menu, then tap [Tide Heights].
Page 88
3. 3D DISPLAY, OVERLAYS How to display the tide graph • Display tide graph for a tide station: Tap a tide icon then tap the pop-up window. • Display tide graph for the tide station nearest the selected position: Tap the desired position on the chart, then tap [Info].
3. 3D DISPLAY, OVERLAYS 3.2.5 Tidal current overlay The tidal current overlay is made from the tidal current data received from NOAA sat- ellites, available in North America. How to display the tidal current overlay Open the [Layers] menu, then turn [Tidal Currents] on. Arrows of more than one color and size appear on the screen and are pointing in different directions.
Page 90
3. 3D DISPLAY, OVERLAYS How to display the tidal current graph Tap a tidal current icon to display the pop-up window. Tap the pop-up window to show the [Current] graph window Clock icon Time scale Tidal current speed at the selected time How to read the tidal current graph •...
Page 91
3. 3D DISPLAY, OVERLAYS This page is intentionally left blank. 3-12...
POINTS, EVENT MARKS About Points, Event Marks In navigation terminology, a point is any location you mark on the chart plotter, radar, sounder or weather display. A point can be a fishing spot, reference point or other im- portant location. You can use a point you have entered to set as a destination. This unit has 30,000 points (including event marks, MOB marks) into which you can enter position information.
4. POINTS, EVENT MARKS How to Enter a Point, Event Mark 4.2.1 How to enter a point (plotter and radar displays only) Method 1: Selected position 1. Tap the position on the screen where to put a point. 2. Tap [New Point] on the pop-up menu. The default point symbol is put at the position selected.
4. POINTS, EVENT MARKS How to Display Point, Event Mark Information Tap a point or event mark to display its information. The information shown depends on the display in use and the object tapped. Point, event mark information (Plotter and radar displays) Event mark information (Sounder display) Event Mark Comment...
4. POINTS, EVENT MARKS Default Point Settings The equipment saves a point under the shape, color, size and type set on the [Set- tings] - [Points] menu. If you want to change the default settings for a point, do as fol- lows: 1.
4. POINTS, EVENT MARKS How to Find Number of Points Used Open the home screen, then tap [Settings] - [General]. Find [Points] in the [DATA US- AGE] section. In the example below, 10 of 30,000 points have been used. How to Move a Point You can move a point by two methods, on the screen and from the points list.
4. POINTS, EVENT MARKS How to Delete a Point You can delete points by two methods, on the screen and from the points list. The point currently set as a go to point cannot be deleted. 4.8.1 How to delete a point on the screen Tap the point to delete then tap [Delete] on the pop-up menu.
4. POINTS, EVENT MARKS How to Edit a Point You can edit the points which you have entered by two methods, on the screen and from the points list. 4.9.1 How to edit a point on the screen 1. Tap the point to edit to show the pop-up menu. Point editing tools 2.
4. POINTS, EVENT MARKS 3) Repeat steps 1) and 2) to complete the name. The maximum length of the name is 20 alphanumeric characters. 4) Tap to confirm. 3. To change the position, tap [Edit Pos] to display the software keyboard. Set the position referring to the instructions in step 2.
Page 100
4. POINTS, EVENT MARKS 3. The list can be sorted by name, icon, color o r range. Tap a corresponding button at the top of the list to sort. The sort method currently selected is highlighted in gray. [Name]: Points sorted in alphanumeric order. [Icon]: Points sorted by symbol shape order.
4. POINTS, EVENT MARKS 4.10 How to Move a Point to the Screen Center You can easily place a point at the center of the plotter display from the points list. 1. Open the home screen, then tap [Lists]. 2. Tap [Points] to open the points list. 3.
4. POINTS, EVENT MARKS 4.12.1 How to go to an on-screen point 1. Tap the desired point to show the pop-up menu. 2. Tap [Goto]. Arrival area (Appears when Go to point you select [Circle and Cross Line] or [Circle] in the [Routes] - [Waypoint Thick red dashed line: Switching Mode].)
4. POINTS, EVENT MARKS 4.12.2 How to go to a position selected on screen You can set a position as a point to go to without saving the point. The point is erased when the navigation is canceled or the power is turned off. 1.
4. POINTS, EVENT MARKS 4.12.3 How to go to a point selected from the points list 1. Open the home screen, then tap [Lists]. 2. Tap [Points] to open the points list. 3. Tap [Name], [Icon], [Color] or [Range] at the top of the list to sort the list. 4.
4. POINTS, EVENT MARKS Auto mode Blue arrow: Course to steer Gray arrow: Heading Heading Set course Fine adj. button(1°) Red: minus, Green: plus Coarse adj. button* Red: minus, Green: plus * Selectable between 2° and 30° with [Autopilot Step] in the [Routes] menu. Use the course adjustment buttons to set the course to steer.
4. POINTS, EVENT MARKS 4.13 How to Restart or Cancel Navigation to a Point 4.13.1 How to restart navigation to a point When you go to a point, you can restart Line 2 the navigation to the point from the cur- rent location.
Page 107
4. POINTS, EVENT MARKS This page is intentionally left blank. 4-16...
ROUTES What is a Route? A route is a series of route points leading to a final destination. When you follow a route, the equipment automatically switches route points and provides pertinent navi- gation data. The equipment can store a maximum of 200 routes with a maximum of 500 points per route.
5. ROUTES How to Create a Route 5.2.1 How to create a new route from the plotter screen 1. Tap a location on the screen for the 1st point in the route to display the pop-up menu. 2. Tap [New Route]. The flag mark appears on the selected position and the route information box appears (at the top of the screen).
5. ROUTES 5.2.2 How to create a new route with points You can create a route with points (including event marks) you have previously en- tered. 1. Tap a point to display the pop-up menu. 2. Tap [New Route]. The flag mark as below appears on the point. The flag mark ap- pears on the selected position and the route information box appears (at the top of the screen).
5. ROUTES 5.2.3 How to create a route from the points list 1. Open the points list. 2. Tap the point to be the first point in the route then tap [Add to Route]. Repeat to add all required points. The route is drawn on the plotter screen. 3.
5. ROUTES 3. Move the route point to the new position by dragging the route point or tapping the new position. 4. Tap [End Move] at the top right-hand corner of the screen. 5.3.3 How to delete a point (incl. route point) on a route You can delete a point on a route.
5. ROUTES Routes List The created routes are stored in the routes list, where you can edit or see the route data. The list stores the following route data for each route: • Name of route • Length of route •...
Page 114
5. ROUTES 3. Tap the route to view. 4. From the [EDITION] section, you can edit the name, from point, to point, color and comment for the route. 5. To find details about the route, tap [Detail]. Route speed Departure date adjustment button adjustment button [Route Speed] button: Change the route speed to use to follow the route.
5. ROUTES [BTW]: Bearing to waypoint. [SPEED]: The speed set with [Default Planning Speed] in the [Routes] menu. [DISTANCE]: Distance between adjacent waypoints. [TOTAL]: Cumulative distance. [TTG]: Time to go between adjacent waypoints. [TOTAL]: Cumulative time in route. 6. To edit the route, tap the point to process to show the [Edit] menu. [Start Nav]: Starts navigation of the route from the point selected.
5. ROUTES How to Delete a Route You can delete routes individually or collectively. An active route cannot be deleted. 5.7.1 How to delete a route on the screen Tap a route leg of the route to delete to show the pop-up menu, then tap [Delete]. 5.7.2 How to delete a route from the routes list 1.
5. ROUTES How to Follow a Route Before you follow a route, make sure that the path to the route is clear. Make sure to zoom your chart to check for hazards that do not appear on a smaller scale. 5.9.1 How to follow an on-screen route 1.
5. ROUTES 5.9.2 How to follow a route selected from the routes list 1. Open the home screen, then tap [Lists] - [Routes]. 2. Tap the route to follow then tap [Goto]. 3. Tap the close button to finish. The following occurs: •...
5. ROUTES 5.9.4 How to show the detailed information about a route Tap a route leg of the route, then Tap [Detail] to show the [Route Detail] window. 5.10 Operations When You Follow a Route 5.10.1 How to restart navigation When you follow a route, you can re- Line 2 start the navigation to the next route...
5. ROUTES 5.10.5 Waypoint switching mode When you arrive to a route point, your unit automatically changes to the next route point according to the waypoint switching mode selected on the menu. [Cross Line]: Change the waypoint when the ship moves through an imaginary cross line (vertical line) that passes through the center of the destination point.
5. ROUTES 5.10.7 XTE lines The color of the XTE line is red for the port side, green for the starboard side. You can show or hide these lines and set their distance from own ship as follows. 1. Open the home screen, then tap [Settings] - [Routes]. 2.
5. ROUTES 5.10.10 Steering a route with the NAVpilot The NAVpilot can be used to steer a route, from the NAVpilot control box in the data area. The figure belows shows the NAVpilot control box in the Nav and Auto modes. See paragraph 4.12.4 for details.
5. ROUTES 5.11 Routes Menu This section provides descriptions for the items in the [Routes] menu not previously mentioned. [Default Route Color]: Select the color of the routes. The options are red, blue, green, yellow, magenta, orange, cyan, or black & white. [Route Thickness]: Select the thickness of the routes.
Page 124
5. ROUTES [Cruising Speed for Planning]: Set the default cruising speed for routes (see section 5.4). [Reset Default Settings]: Select this menu item to restore default settings for the [Routes] menu. 5-17...
Page 125
5. ROUTES This page is intentionally left blank. 5-18...
RADAR This chapter provides the information necessary for radar operation., which requires a radar sensor. Note: To change the radar source, go to the Home screen, tap [Settings] - [Radar] - [Radar Source], then tap desired radar source. How to Transmit, Set the Radar in Stand-by Tap the [TX] icon at the bottom right corner of the screen to put the radar in transmit or stand-by state.
6. RADAR How to Adjust the Gain You can adjust the gain (sensitivity) of the radar receiver. The correct setting shows some background noise on the screen. If you do not use enough gain, weak echoes are erased. If you use more gain than necessary, the background noise hides both weak and strong targets.
6. RADAR Method 2: Radar Control data box in data area The gain can be adjusted from the data area, with the [Radar Control] box in the [RA- DAR] data box. On the box, tap the [M/A] part of the [Gain] flipswitch to switch between manual and automatic adjustment.
6. RADAR How to Reduce the Rain Clutter When your ship is in or near rain or snow, the reflections from rain or snow appear on the screen. These reflections have the name "rain clutter". When the rain clutter is strong, targets in or near the rain clutter are hidden in the clutter.
6. RADAR Orientation Mode The orientation mode controls the relationship between your ship and all the other tar- gets. The heading data is required in the north-up mode. When the heading data is lost, the orientation mode automatically goes to head-up. Restore the compass signal to show the heading indication.
6. RADAR How to Measure the Range and Bearing from Your Ship to a Target You can measure the range or bearing to a target by the following four methods. Range Bearing measurement measurement EBL (Electronic Bearing Line) Fixed range rings Ruler VRM (Variable Range Marker) 6.8.1...
6. RADAR 6.8.3 How to select the range rings mode To select the range rings mode, open the home screen, then tap [Settings] - [Radar]. Set [Bearing Scale Mode] and [Relative] or [True]. Head-up mode Heading line North (“0”) Boat icon Bearing scale...
6. RADAR 6.8.4 How to measure the range and bearing to an object Tap an object to get its range and bearing from own ship. Read the range and bearing in the pop-up menu. Range and bearing to object Acquire Object New Point Goto...
Page 134
6. RADAR Method 2: From the pop-up menu Tap the screen to show the pop-up menu, then tap [VRM]. Drag the VRM or slider to set the VRM. Tap [End VRM] to anchor the VRM and finish. The range to the VRM appears to the left of the slider bar.
6. RADAR 6.8.6 How to measure the bearing with the EBL Method 1: From the data area Open the data area. Tap the EBL indication in the [EBL/VRM] data box. Drag the EBL or slider to set the EBL. Tap [End EBL] to anchor the EBL and finish. The bearing of the EBL appears to the left of the slider bar and in the [EBL/VRM] data box.
6. RADAR Method 2: From the pop-up menu Tap the screen to show the pop-up menu, then tap [EBL]. Drag the EBL or slider to set the EBL. Tap [End EBL] to anchor the EBL and finish. The range to the EBL ap- pears to the left of the slider bar.
6. RADAR How to Measure the Range and Bearing Between Two Targets You can measure the range and bearing between any two targets with the ruler. 1. Open the slide-out menu then tap [Distance] to display the ruler, which has two draggable circles connected with a line.
6. RADAR 6.11 Heading Line The heading line indicates your heading in all orientation modes. This line connects between your position to the outer edge of the radar display. The line is at zero de- grees on the bearing scale in the head-up mode. The orientation of the line changes in the north-up mode with the movement of your ship.
6. RADAR 6.13.2 How to activate or deactivate the guard zone 1. Tap on a line of the guard zone to show the pop-up menu. 2. Turn [Alarm] on or off. The alarm is active when the guard zone lines are solid and the lines are dashed when the alarm is deactivated.
6. RADAR 6.15 How to Show, Hide or Cancel an Active Route You can show, hide the active route on the radar display. Open the [Layers] menu then turn [Routes] on or off. To cancel route navigation, tap any part of the route then tap [Stop Nav] on the pop- up menu.
6. RADAR 6.18 Background Color You can select the background color for daytime and nighttime operations. 1. Open the home screen, then tap [Settings] - [Radar]. 2. Tap [Day Background Color] or [Night Background Color] menu. Day background color Night background color 3.
6. RADAR 6.19 Dual-Range Display The dual-range display scans and displays two different radar ranges at the same time, with a single antenna. There is no time delay between the two pictures and, with the magnetron radar, you have separate control of each picture. (The solid state radar has some restrictions.
6. RADAR The no.1 screen is independent of the no.2 screen when the no.2 screen is in stand- by. However, when the no.2 screen goes to transmit state, so does the no.1 screen. No.2 No.1 screen screen No.1 No.2 No.1 No.1 screen screen...
6. RADAR Target which is moving and getting Targets other than closer to own ship targets moving and (red) getting close to own ship, or rain clutter Rain clutter (green) (blue) 6.20.1 How to activate or deactivate the target analyzer Turn [Target Analyzer] on or off from the pop-up menu.
Page 145
6. RADAR This mode has three sets of preset picture adjustment settings, low, medium, and high. The high setting provides the greatest degree of sensitivity, which makes it suit- able for long range detection of birds. Turn off the interference rejector off to make detection of weak echoes easier. Turn on the interference rejector during a voyage.
6. RADAR 6.23 Radar Menu This section provides the descriptions for the radar menu items not mentioned earlier. Radar Initial Setup [Antenna Rotation]: Starts or stop antenna rotation. For the serviceman. See the in- stallation manual. [Antenna Heading Align]: Compensates for error in positioning of the antenna unit at installation.
6. RADAR [Auto Tuning]: Activate or deactivate auto tuning for the connected radar. Not avail- able with DRS4D-NXT. [Tuning Source]: Selects the radar range for the adjustment, [Range 1] (long range), [Range 2] (short range). Not available with DRS4D-NXT. [Manual Tuning]: Manually tune. Not available with DRS4D-NXT. [Radar Monitoring]: Show various voltage levels, and ARPA data.
Page 148
6. RADAR Virtual image A large target near your ship can show at two positions on the screen. One of the po- sitions is the true echo reflected by the target. The other position is a false echo which is caused by the "mirror effect" of a large object on or near your ship. See the figure shown below for an example of this type of false echo.
6. RADAR Sidelobe echoes Each time the radar transmits, some radiation leaves on each side of the beam. This lost energy has the name "sidelobes" If a target is detected by both the sidelobes and the mainlobe, the sidelobe echoes can appear at both sides of the true echo at the same range.
6. RADAR 6.24.3 Racon (Radar Beacon) A racon is a radar transponder that sends a characteristic signal when the racon re- ceives a radar pulse (normally only the three-centimeter band). If the racon signal is sent on the same frequency as that of the radar, the signal appears on the radar dis- play.
6. RADAR 6.25 ARPA Operation The ARPA (Automatic Radar Plotting Aid) shows the movement of a maximum of 30 radar targets. The targets can be acquired manually or automatically. All 30 targets can be acquired manually when the ARPA acquisition area is not active. If the ARPA acquisition area is active, that total is equally divided between manual and auto acqui- sition.
6. RADAR 6.25.2 How to manually acquire a target You can manually acquire a target from both the radar display and the radar display overlay. Tap the target to acquire to show the pop-up menu, then tap [Acquire]. After you acquire a target, the radar marks the target with a broken square and a vec- tor appears within 30 s (default setting).
6. RADAR Auto acquisition by Doppler is OFF in the default setting. To activate this feature, open the [Radar] menu, then turn on [Auto acquire by Doppler]. This feature requires the radar sensor DRS4D-NXT and position and heading inputs. 6.25.5 How to display target data You can find the bearing, range, etc.
6. RADAR 6.25.7 ARPA list The ARPA list displays data for all ARPA targets being tracked. How to show the ARPA list To show the list, go the Home screen, then tap [Lists] - [ARPA]. The color bars at the left side of the list denote ARPA symbol status, green for tracking or lost target, red for dangerous target.
6. RADAR 6.25.8 How to clear lost targets Tracking of a target cannot be continued when the echo from that target becomes lost. A lost target can be tracked after it is reacquired. Lost targets can be erased individu- ally or collectively. Individual target Tap the target to display the pop-up menu, then tap [Clear] to remove the target from the screen.
6. RADAR 6.25.10 CPA graphic display The CPA graphic display shows the CPA between own vessel and the selected ARPA (or AIS) target with a line, called the “CPA line.” You can use the line to monitor speed and heading changes of another vessel, which makes it useful as an anti-collision aid, especially in congested waters.
Page 157
6. RADAR This page is intentionally left blank. 6-32...
FISH FINDER (SOUNDER) This chapter describes the functions of the built-in fish finder. Note: To change the fish finder source, go to the Home screen, tap [Settings] - [Sounder] - [Sounder Source], then tap desired fish finder source. How the Fish Finder Operates The fish finder calculates the distance between its transducer and underwater objects like fish, lake bottom or seabed.
7. FISH FINDER (SOUNDER) How to Select a Display Your fish finder has six display modes. These modes are single frequency, dual fre- quency, bottom zoom, bottom lock, A-scope, and bottom discrimination. 7.3.1 Single frequency display The single frequency display shows either the low-fre- quency or high-frequency picture on all the screen.
7. FISH FINDER (SOUNDER) 7.3.2 Dual frequency display The dual frequency display provides both low and high frequency pictures, the low fre- quency on the left half (default). Use the dual frequency display to compare the same picture with two different sounding frequencies. High frequency frequency...
7. FISH FINDER (SOUNDER) Bottom zoom display The bottom zoom display expands the bottom and the fish near the bottom according to the zoom range selected on [Zoom Range Span] in the [Settings] - [Sounder] menu. This display helps you find the density of the bottom. A short echo tail normally indi- cates a soft bottom (sand bottom, etc.).
1. Open the home screen, then tap [Settings] - [Sounder]. 2. Tap [Fish Finder Source]. 3. Tap [TZTL12F],[TZTL15F], [BBDS1] or [DFF1-UHD] as applicable. 4. Tap the close button to finish. 5. To activate or deactivate the bottom discrimination display, turn [Bottom] on or off from the pop-up menu.
7. FISH FINDER (SOUNDER) 7.4.2 How to select an automatic fish finder mode There are two types of automatic fish finder modes: [Auto Fishing] and [Auto Cruising]. [Auto Fishing] searches for schools of fish, and [Auto Cruising] tracks the bottom. [Auto Cruising] uses a higher clutter removal setting than [Auto Fishing].
7. FISH FINDER (SOUNDER) 7.5.4 How to adjust the gain The gain controls how echoes of different strengths are displayed. Set the gain to show a slight amount of noise on the screen. Increase the gain for greater depths and lower the gain for shallow waters.
7. FISH FINDER (SOUNDER) Picture Advance Speed The picture advance speed controls how quickly the vertical scan lines move across the screen. A fast advance speed expands the size of a school of fish horizontally on the screen. A slow advance speed shortens the school of fish. Use a fast advance speed to see the hard bottom.
7. FISH FINDER (SOUNDER) How to Reduce Interference Interference from other fish finders and electrical equipment appears on the screen as shown in the illustration. When these types of interference appear on the screen, use the interference rejector to reduce the interference. Turn off the interference rejector when there is no interference, so that you do not erase weak echoes.
2. Drag the slider in [TVG HF] (high frequency) or [TVG LF] (low frequency) to set the level. The TVG setting method changes with the fish finder connected. Fish finder TVG setting method Internal sounder (TZTL12F or TZTL15F), The higher the setting the greater DFF1, DFF1-UHD, BBDS1 the distance gain.
7. FISH FINDER (SOUNDER) 7.11 Fish Finder Alarms Two types of fish alarms release audio and visual alarms to tell you that echoes from fish are in the area you selected. These alarms are [Fish Alarm] and [Fish Alarm for Bottom Lock].
7. FISH FINDER (SOUNDER) 7.11.2 How to activate or deactivate an alarm Fish alarm 1. Open the home screen, then tap [Settings] - [Sounder]. 2. Turn [Fish Alarm] on or off. The fish alarm can also be activated or deactivated with [Fish Alarm] on the pop-up menu.
7. FISH FINDER (SOUNDER) • 50 kHz and 200 kHz beams are transmitted alternately without reference to the cur- rent display mode. • Use this feature with ship speed of 10 knots or less and depth between 2 and 100 m. •...
7. FISH FINDER (SOUNDER) 7.12.2 Fish size correction The fish size shown on the screen can be different from the true size. If the size is wrong, add an offset to the measured value to get a more accurate indication on the screen.
™ To use RezBoost , set the fish finder source (with [Fish Finder Source] on the [Sounder] menu) to TZTL12F or TZTL15F as appropriate. ™ How to set RezBoost Tap the sounder display to show the pop-up menu, then scroll the menu to show [Rez Boost].
7. FISH FINDER (SOUNDER) 7.14 Temperature Graph With connection of a water temperature sensor, you can plot sea surface temperature over time. Open the pop-up menu and turn on [Temperature]. The temperature graph runs across the screen from right to left, the latest temperature at the right edge. The temperature scale is at the left edge of the display.
7. FISH FINDER (SOUNDER) 7.15 Sounder Menu This section describes the fish finder functions not described in previous sections. Open the home screen, then tap [Settings] - [Sounder]. ACCU-FISH Info ACCU-FISH Symbols ACCU-FISH Size Correction [Day Background Color]: Select the background color for use during daylight hours. The options are [White], [Light Blue], [Black] and [Dark Blue].
Page 175
7. FISH FINDER (SOUNDER) [Transmit Rate Auto]: Automatically set the transmit rate according to ship’s speed, and is inoperative when there is no speed data. [Transmit Rate Manual]: Change the TX pulse repetition rate in 21 levels (21 is high- est power.).
Page 176
7. FISH FINDER (SOUNDER) [Transducer Setup]: Select the method to setup the transducer, by model, manually, or TDID (transducer ID). See the installation manual for details. [Transmission Power]: Interference can appear on the screen when the fish finder on your ship and another ship have the same TX frequency. To prevent this interfer- ence, lower your TX power and ask the other ship to lower their TX power.
7. FISH FINDER (SOUNDER) [Set Hardware to Factory Default]: Select this menu item to restore default settings for the unit selected in [Fish Finder Source]. [Reset Default Settings]: Select this menu item to restore default settings for the [Sounder] menu. 7.16 Interpreting the Display Zero line...
Page 178
7. FISH FINDER (SOUNDER) Bottom contour The tail from a hard bottom is longer than the tail from a soft bottom, because the hard bottom reflects more of the ultrasonic pulse. An echo from shallow water gives a stron- ger reflection than the echo received from deep water. A longer bottom tail appears on slopes, because of the difference in travel time at both edges of the beam angle.
Page 179
7. FISH FINDER (SOUNDER) Size of a school of fish Usually the size of fish echoes on the screen is proportional to the actual size of the school of fish. However, if two fish echoes appear at different depths with the same size, the school of fish at the shallower depth is larger because the ultrasonic beam widens as it propagates and a school of fish in deep water is displayed larger.
Page 180
7. FISH FINDER (SOUNDER) Plankton A plankton layer appears as a large amount of green or blue dots, and is a possible location for fish. A plankton layer moves down in the day and School of fish up at night. Plankton Current rip When two ocean currents of different speeds di-...
Page 181
7. FISH FINDER (SOUNDER) False echo When an ultrasonic pulse is transmitted, some energy leaves from each side of the beam. This energy has the name "sidelobe". Echoes from sidelobes show on the screen as false images like in the illustration shown below. Mainlobe Mainlobe False image...
FILE OPERATIONS Points, tracks, routes and settings can be read and written, using the USB port on this ™ unit. Further, with a My Time Zero account, you can save settings data to the cloud. The card slot at the back of this unit is exclusively for use with chart cards. The table below outlines the media that can be used with your unit.
8. FILE OPERATIONS 2. Tap [Export File Format]. 3. Tap [TZD], [CSV] or [GPX]. [TZD]: For NavNet TZtouch2 [CSV]*: For use with NavNet 3D *: The CSV format has the following export restrictions: - 2,000 points maximum - 200 routes (100 points per route) maximum - 10,000 track points maximum [GPX]: For use with PC plotter 4.
8. FILE OPERATIONS How to Import Points and Routes You can import points and routes to the internal memory of this unit, using a SD card, micro SD card or USB flash memory. 1. Put the appropriate media in the USB port or a slot in the SD Card Unit. 2.
8. FILE OPERATIONS 3. Tap [SDCardRight] (or [SD CardLeft]) on the SD card unit, or [External] for USB port. You are asked if you are sure to export points and routes. 4. Tap a tracks file. You are asked if you are sure to export tracks. 5.
8. FILE OPERATIONS How to Load the Equipment Settings You can load saved settings data from an appropriate media to this unit, and share them with the NavNet TZtouch2 units in the NavNet network. 1. Put the appropriate media in the USB port or a slot in the SD Card Unit. 2.
8. FILE OPERATIONS 8.7.2 How to retrieve settings data from the cloud Do as follows to retrieve settings data from the cloud. 1. Open the home screen, then tap [Settings][General]. ™ 2. Tap [Login] at the SOCIAL NETWORK section and login to your TimeZero count.
8. FILE OPERATIONS ™ My TimeZero Cloud Data Service ™ My TimeZero cloud data service allows you to back up your data and synchronize it ™ among your My TimeZero devices, as well as sharing it with your friends. Create a ™...
Page 189
8. FILE OPERATIONS This page is intentionally left blank.
CAMERA/VIDEO/FUSION-Link The camera/video function allows you to use your unit to play back images from a vid- eo player, on-board camera, or DVD player. A video signal can be seen only on the NavNet TZtouch2 unit that receives the video signal. Image size, brightness, contrast and color of images can be adjusted.
9. CAMERA/VIDEO/FUSION-Link Video Signal Type There are two types of video signals connected to this equipment. • Analog: Images from a video player, on-board camera or DVD player • FLIR: Images from a FLIR brand infrared camera How to Set the Video Display 9.3.1 How to set the video signal FLIR camera...
9. CAMERA/VIDEO/FUSION-Link 9.3.2 How to adjust the image size You can adjust the image size from the pop-up menu. 1. In the camera mode, tap the screen to show the pop-up menu. 2. Tap the camera display to ad- Image size selections just.
9. CAMERA/VIDEO/FUSION-Link Control of FLIR Camera [Camera FoV] menu You can display the field of view by the FLIR camera on the plotter display. 1. Tap the boat icon to display the pop-up menu. 2. Tap [Cone]. The boat icon is put inside a red translucent circle. [Move Camera] and [Lock Camera] menus You can rotate the FLIR camera about the position you select (touch) on the plotter or radar display.
9. CAMERA/VIDEO/FUSION-Link Touch Control on the Camera Display Operations available with connection of an analog camera Operation Function Opens the pop-up menu. Operations available with connection of a FLIR camera Operation Function Points camera to direction tapped. Long tap Opens the pop-up menu. Drag Rotates camera while drag- ging.
9. CAMERA/VIDEO/FUSION-Link FUSION-Link FUSION-Link allows compatible NavNet TZtouch2 displays to interface and achieve control of specialized FUSION marine entertainment equipment. 9.7.1 How to access the FUSION screen and controls The FUSION controls can be accessed three ways: • From the home screen (full screen) •...
Page 196
9. CAMERA/VIDEO/FUSION-Link Drag bar to adjust squelch. Tap to select CH16. Channel selection mode Hide or show menu. Lower volume. Select channel. Tap: Switch channel selection mode between Mute/unmute. preset and manual. Long tap: After selecting channel in manual mode, long tap to register the channel as preset channel.
9. CAMERA/VIDEO/FUSION-Link Tap to go to full screen FUSION display. Tap to hide bar. For iPod For VHF 9.7.2 FUSION settings Open the Home screen, tap [Initial Setup], then scroll down to find the [FUSION] sec- tion. Set the [FUSION] items referring to the descriptions shown below. [Connect to Fusion]: Connects to your FUSION equipment.
10. INSTRUMENT DISPLAY The instrument display provides comprehensive navigation and environment data. The instrument display can be programmed to a full screen or three-way split screen. Applicable sensors are required. 10.1 How to Show the Instrument Display Set the instrument display on the home screen referring to paragraph 1.7.1. Tap the instrument display icon to show the instrument display.
10. INSTRUMENT DISPLAY 10.2 Instrument Displays This section provides examples of the available instrument displays, with their default configurations. Your displays may be different depending on your system configura- tion. The instrument theme is available in black (default color) or white. The sample dis- plays shown in this chapter use the white theme.
Page 205
10. INSTRUMENT DISPLAY Tank display The tank indication shows fuel level in both analog and digital formats. The analog in- dicator rises or lowers with fuel level and the color changes according to the percent- age of fuel remaining. Green: 10% - 100% Red: 0% - 10% 10-8...
10. INSTRUMENT DISPLAY 10.2.3 How to switch between instrument displays 3-way split screen The default display screens in the 3-way split screen are environment, wind, numeric, highway, NAVpilot, single engine, twin engines, triple engines, and tank. The availabil- ity of a display depends on your system configuration. You can switch between the displays by swiping downward at the bottom of the dis- play, or tapping the screen to display the pop-up menu shown below and tapping the display of your choice.
Page 207
10. INSTRUMENT DISPLAY Full screen The default full screens are [Full 1], [Full 2], [Single Engine], [Twin Engines], [Triple Engines], and [Quad Engines]. (The availability of the displays depends on your sys- tem configuration.) You can switch between the displays by swiping downward at the bottom of the display, or tapping the screen to display the pop-up menu shown below and tapping the display of your choice.
10. INSTRUMENT DISPLAY 10.3 How to Edit the Instrument Displays The instrument displays are fully customizable. You can edit the displays as follows: • Remove an indication from a display • Add an indication to a display • Rearrange the indications in a display •...
10. INSTRUMENT DISPLAY 10.3.3 How to edit, remove an indication in an instrument display 1. Prepare the display for editing as shown in paragraph 10.3.1. 2. Tap the indication to process to show the [Edit Instrument] pop-up menu. 3. Do one of the following depending on your objective: •...
Page 210
10. INSTRUMENT DISPLAY • Change the indication type: Tap [Change Type] to show the [Edit Instrument] pop-up menu, shown on the next page. [GRAPHIC] changes the size of a graphic indication or changes a numeric indication to the corresponding graphic indication.
10. INSTRUMENT DISPLAY 10.3.4 How to add an indication to an instrument display 1. Prepare the display for editing as shown in paragraph 10.3.1. 2. Tap an unoccupied position on the display to show the [Add Instrument] pop-up menu. (If there is no space available, remove an unnecessary indication following the procedure in paragraph 10.3.3.).
10. INSTRUMENT DISPLAY 10.3.7 How to add an instrument display Ten full size and six split screen instrument displays are preset in this equipment. If the displays do not meet your requirements, you may add custom displays as neces- sary. A maximum of ten each of full screen and split screen displays is available. 1.
10. INSTRUMENT DISPLAY 10.4 Instrument Theme The instrument theme is available in black or white. To change the theme, go to the home screen and tap [Settings] - [General]. Set [Instrument Theme] to [Black] or [White]. The setting also controls the graphic format navigation data displays in the data area.
U.S. Information provided by the Sirius Marine Weather service is advisory in nature. You, the customer, agree to release FURUNO ELECTRIC CO., LTD., Sirius Satellite Radio Inc., Navcast Inc. and WSI Corporation from any problems that occur from this ser-...
11. SIRIUS/XM SATELLITE WEATHER RECEIVER (BBWX3) OPERATIONS vice. And you acknowledge that you have read the conditions of your subscription agreement and agree to all the conditions of the subscription. If you do not have the subscription agreement, got to www.sirius.com/marineweatheragreement or call 1- 800-869-5480 to have a copy sent to you.
Page 216
11. SIRIUS/XM SATELLITE WEATHER RECEIVER (BBWX3) OPERATIONS 4. Tap [Tidal Step]. 5. Tap the update interval (which determines how often tidal data are captured) for the tide icon. 6. Tap [Duration of Animation]. 7. Tap the update interval for the animation. The larger the time, the slower the ani- mation moves.
11. SIRIUS/XM SATELLITE WEATHER RECEIVER (BBWX3) OPERATIONS 11.2.2 How to download the NavCenter weather data 1. Open the home screen, then tap [Settings] - [General]. 2. Tap [Wireless LAN Settings]. 3. Turn on [Wireless]. 4. After the internet connection is established, tap the close button to exit. 5.
11. SIRIUS/XM SATELLITE WEATHER RECEIVER (BBWX3) OPERATIONS 11. Open the weather display, then tap the screen to show the pop-up menu. Tap [Get Latest Wx]. The notification bar at the top of the screen flashes "Weather Update in Progress" during the downloading. If the downloading was successful, the message " DOWN- LOAD SUCCEEDED"...
11. SIRIUS/XM SATELLITE WEATHER RECEIVER (BBWX3) OPERATIONS 11.2.4 How to load a weather file You can load a weather file saved on a micro SD card or USB flash memory. 1. Set the appropriate USB flash drive in the USB port. For use of the SD Card Unit, set the appropriate micro SD card in one of the slots on the unit.
11. SIRIUS/XM SATELLITE WEATHER RECEIVER (BBWX3) OPERATIONS 11.3.2 How to display the Sirius data [Wx Radar] (Weather radar) NOWRAD and Canadian weather radar information are put on top of your chart (see paragraph 11.3.1). This display lets you see possible storm fronts to help you identify the clouds from possible sea clutter.
11. SIRIUS/XM SATELLITE WEATHER RECEIVER (BBWX3) OPERATIONS [Anim Radar] (Animation radar) The animation radar display provides the past weather radar information. To show the animation radar display, tap [Anim Radar] on the pop-up menu. To stop the animation display, tap [End Anim] at the top right-hand corner of the screen. 11.4 Weather Icons (Sirius Weather) The table below shows the weather icons that appear on the Sirius marine weather...
11. SIRIUS/XM SATELLITE WEATHER RECEIVER (BBWX3) OPERATIONS 11.5 Weather Data (NavCenter or Sirius) The table below shows the weather data available for displaying according to weather data server (NavCenter or Sirius). Items NavCenter Sirius Item NavCenter Sirius Wind Currents Waves Altimetry Plankton Cloud...
Page 223
11. SIRIUS/XM SATELLITE WEATHER RECEIVER (BBWX3) OPERATIONS [Rain/Snow]: The rain/snow fore- cast displays rain/snow images. 0.1 mm/hour of rainfall/snowfall (mini- mum) is displayed in green, 5 mm/ hour (maximum) in dark violet. 4,979 [Air Temp]: The air temp forecast displays the air temperature by col- or.
Page 224
11. SIRIUS/XM SATELLITE WEATHER RECEIVER (BBWX3) OPERATIONS Pressure icon Meaning Trough Squall line Dry line Isobars 1010 [500mb]: The 500mb forecast dis- plays the contour lines over 500 mb. 4,898 [SST] (Sea surface tempera- ture): This data layer shows the temperature of the sea surface in shades.
11. SIRIUS/XM SATELLITE WEATHER RECEIVER (BBWX3) OPERATIONS [Currents]: The current forecast dis- plays the tidal current speed and di- rection by blue arrow. The darker the blue, the faster the current speed (0 to 2 kn). 1,621 [Altimetry]: The altimetry forecast displays the sea height anomalies by color.
11. SIRIUS/XM SATELLITE WEATHER RECEIVER (BBWX3) OPERATIONS Method 2: From the home screen Open the slide-out menu, then tap the [Sirius Audio] icon to show or hide the audio control bar. See the next page. Sirius Audio icon 11.6.2 How to operate the radio controls Full screen controls Channel, music genre Signal strength...
Page 227
11. SIRIUS/XM SATELLITE WEATHER RECEIVER (BBWX3) OPERATIONS Audio control bar controls Preset channels Artist, title Channel, Raise music volume. genre Mute, unmute. Lower volume. 11-14...
12. AIS, DSC MESSAGE 12.1 What is AIS? AIS (Automatic Identification System) is a system that continuously transmits the iden- tification and position of your ship to AIS-equipped ships within VHF range. All such ships also receive data from other AIS-equipped ships and display their positions and other relevant information.
12. AIS, DSC MESSAGE Target Symbol Description type Lost AIS An AIS target becomes a lost target target if a signal is not received from the AIS target for x* min- utes. The lost target symbol is erased if a signal is not re- Color - AIS target: Blue for the Class A AIS ceived for an additional x* min-...
12. AIS, DSC MESSAGE 2. Turn on [Proximity AIS Target Alarm]. 3. Tap [Proximity AIS Target Alarm Value] to open the software keyboard. 4. Set the alarm value, then tap . 5. Tap the close button to finish. 12.5 How to Ignore Slow Moving AIS Targets The proximity AIS target alarm may often sound in areas of heavy vessel traffic.
Tap an AIS target (plotter or radar display) to display the simple information in the pop- up menu. For detailed information, tap the target, then tap [Info] on the pop-up menu to show the [Target Info] window. Name FURUNO MMSI 124365890 GALE WARNING 27.16N 82.40W 342.0°...
12. AIS, DSC MESSAGE 12.9 How to Show or Hide the Target IDs You can show or hide the target ID of AIS targets. 1. Open the home screen, then tap [Settings] - [Targets]. 2. Turn [Display Target IDs] on or off. 3.
Page 233
How to display the detailed information for an AIS target Tap the AIS target on the AIS list then tap [Detail]. The name of the AIS is shown in the title bar and navigation data appears in the [TARGET INFO] section. FURUNO FURUNO 000886617 How to find an AIS target on the plotter display Tap the AIS target on the AIS list, then tap [Find On Chart].
12. AIS, DSC MESSAGE 12.11 When an AIS SART is Received... When an AIS SART is received (in- cluding re-received ones), the mes- sage "AIS SART Alarm" appears Goto flashing in Status bar. Tap the Sta- tus bar to acknowledge the mes- sage.
12. AIS, DSC MESSAGE 12.13 How to Register an AIS or DSC Target to the Buddies List The buddies list provides a quick reference to ships’ MMSI and nickname. For exam- ple, you might want to enter the MMSI and nickname of partner ships or ships that of- ten operate in your area.
12. AIS, DSC MESSAGE 12.14 CPA Graphic Display The CPA graphic display, which requires own position and heading data, draws a line between own ship position and the selected AIS target. This feature lets you monitor an AIS target’s heading and speed changes. The display is useful as an anti-collision aid, especially in congested waters.
12. AIS, DSC MESSAGE 12.15 AIS Transponder FA-30, FA-50 The FURUNO AIS Transponder FA-30 (or FA-50) installs in the NavNet TZtouch2 net- work and can be controlled from a NavNet TZtouch2 display. To access the menu for the transponder, do as shown below. See the respective operator’s manual for details.
12. AIS, DSC MESSAGE 12.16 DSC Message Information The DSC (Digital Selective Calling) message information feature provides, on the plot- ter and radar displays, the MMSI no. and position* of the ships that have transmitted a DSC message to you. A hexagon-shaped marker marks the position of the ship at the time the DSC was transmitted to you.
Tap a DSC marker to display the simple information (position, MMSI no. of the ship that transmitted a DSC message, etc.). To get detailed information, tap a DSC marker, then tap [Info] on the pop-up menu. FURUNO 5.992 NM TCPA 41’30s...
12. AIS, DSC MESSAGE 12.16.4 The DSC list The DSC list shows the name, MMSI, range, bearing, CPA and TCPA of vessels from which you have received a DSC message. 1. Open the home screen, then tap [Lists] - [DSC]. List sort buttons 2.
Page 241
12. AIS, DSC MESSAGE To see the detailed information for a DSC target, tap a DSC then tap [Detail]. To put a DSC marker at the center of the plotter display, tap the DSC target, then tap [Find On Chart]. 12-14...
13. OTHER FUNCTIONS Once you have become acquainted with your equipment, you can set it according to your needs. You can change system configuration, change how the equipment oper- ates and displays information, etc. 13.1 General Menu The [General] menu contains items that once preset do not require frequent adjust- ment.
13. OTHER FUNCTIONS Menu item Function Options [Cross Cursor Adjust the cross cursor speed. -7 to +7 Speed] [Local Time Off- Select the time difference between local time and UTC -12:00 to UTC +13:00 set] UTC time. (at one-hour intervals) Time Format Select how to display time, in 12 or 24 hour format.
13. OTHER FUNCTIONS Menu item Options [Bearing Display] [Magnetic], [True] The mode (magnetic or true) of all heading and bearing data. [True Wind Calculation [Ground], [Surface] Reference] Select wind value to display from speed over ground or speed through water (surface). [Position Format] [DDD°MM.mmmm’], [DDD°MM.mmm’], [DDD°MM.mm’], [DDD°MM’SS.ss’], [DDD.dddddd°]...
Page 245
13. OTHER FUNCTIONS INSTRUMENTS SETUP section Menu item Description Options (setting range) [Engine & Tank See “Engine & Tank Automatic Setup” below. Automatic Setup] [Engine & Tank See “Engine & Tank Automatic Setup” on the next page. Manual Setup] [Graphic Instruments See “Graphic Instruments Setup”...
Page 246
13. OTHER FUNCTIONS [Graphic Instruments Setup] - [Propulsion Engine] Menu Item Description Options (setting range) [Max. RPM] Set the maximum rpm of your engine to 1 rpm to 20,000 rpm show on the RPM display. [Red Zone Oil Pressure] Set the starting value for the red zone area 0 kPa to 998 kPa of the oil pressure meter.
Page 247
Select the source for each data to input to the system. If two or more sources are connected for a data, select one using the pull-down dialog box. (FURUNO sensors are shown at the upper part of the list.) [Sensor List] Show the information for sensors connected to your equipment.
Page 248
13. OTHER FUNCTIONS FUSION section Menu item Description Options (setting range) [Connect to Fu- Connect to your Fusion equipment. sion] [Fusion Auto Set to [ON] to allow this unit to control the Fusion volume. Volume] [Minimum Set the minimum speed threshold. Exceeding this 0.0 kn to 19.9 kn Speed] speed activates volume auto control.
13. OTHER FUNCTIONS 13.4 Facsimile Receiver FAX-30 The FURUNO Facsimile Receiver FAX-30 installs in the NavNet TZtouch2 network and can be controlled from a NavNet TZtouch2 display. Below are the steps to start fax operation. 1. Connect the FAX-30 to the NavNet TZtouch2 network.
13. OTHER FUNCTIONS 13.5 Software Update You can update the software for this equipment via the internet. See section 1.18 for how to connect to the internet. It is recommended to back up stored data (waypoints, routes, etc.) to a micro SD card (or USB flash memory) before updating the software, in case something should go wrong during the updating.
13. OTHER FUNCTIONS 13.6 How to Manage Your Charts The NavNet TZtouch2 uses the same Mapmedia charts as NavNet 3D. Even though NavNet TZtouch2 is a master-less system in networking, for charts one NavNet TZtouch2 unit should be set as Chart Master to share the System ID, which will be necessary to obtain an unlock code of a chart from Mapmedia.
Free (USA and NOAA) and for-fee NavNet TZtouch2 compatible charts are provided by FURUNO and Mapmedia. Go to the URLs shown below to download chart data. Download the chart file to your desktop. Unzip the file, then copy it to the root of a mi- cro SD card.
13. OTHER FUNCTIONS 13.6.4 How to delete charts Before replacing a chart you should delete the old chart data on every NavNet TZtouch2 unit. Only delete the chart data that you intend to replace or no longer re- quire. Open the charts catalog. Tap the trashcan icon of the chart to delete. You are asked "ARE YOU SURE YOU WANT TO DELETE THIS FILE?"...
14. MAINTENANCE, TROUBLE- SHOOTING This chapter has information about maintenance and troubleshooting that the user can follow to care for the equipment. NOTICE WARNING Do not apply paint, anti-corrosive ELECTRICAL SHOCK HAZARD sealant or contact spray to plastic Do not open the equipment. parts or equipment coating.
The life of the LCD is approximately 18,000 hours for the TZTL15F, and 25,000 hours for the TZTL12F. The actual number of hours depends on ambient temperature and humidity. When the brilliance cannot be raised sufficiently, contact your dealer about replacement of the LCD.
14. MAINTENANCE, TROUBLESHOOTING 14.4 Troubleshooting This section provides simple troubleshooting procedures that the user can follow to re- store normal operation. If you cannot restore normal operation, do not check inside the unit. Have a qualified technician check the equipment. 14.4.1 General troubleshooting Problem...
14. MAINTENANCE, TROUBLESHOOTING 14.4.4 Fish finder troubleshooting Problem Remedy You selected a fish finder dis- • Check that the transducer cable is tightly fastened. play, but no picture appears. • Check that the fish finder source is correct. • If you are using a network fish finder, check that it is properly connected.
APPENDIX 1 MENU TREE Settings menu General Function Gesture (None, Screen Capture, Event, Home, Settings, Lists, Tide) Move Tool on Long Push (OFF, Connect to the Internet (Never, At Startup, When Necessary) Wireless LAN Settings (Open the dialog box for Wireless LAN settings.) User Interface Auto-Hide (0’03s, 0’05s, 0’10 s, 0’15s) Instrument Theme (White, Black) Brilliance Synchronization (OFF, ON)
Page 259
APPENDIX 1 MENU TREE Routes Default Route Color (Red, Blue, Green, Yellow, Magenta, Orange, Cyan, Black) Route Thickness (1 - 10 or 2 - 2) (1 - 10=2D mode, 2 - 11=3D mode) Navigate with Autopilot* (ON, OFF) *Requires NAVpilot. Autopilot Step* (2 - 30(°), 10) Ask to Enter Route Name (ON, OFF) Fuel Max Range (ON, OFF)
Page 260
APPENDIX 1 MENU TREE Points Display Points Names (ON, OFF) Default Point Symbol (Select the default icon for point.) Default Point Color (Red, Blue, Green, Yellow, Magenta, Orange, Cyan, Black) Point Size (50 - 200(%), 100) Icons Set (Modern, Classic) Data to Be Recorded in Event Comment (None, Date, SST, Date And SST) Record Event1 Automatically (ON, OFF) Default Event 1 - 6 Symbol...
Page 261
APPENDIX 1 MENU TREE Plotter Grid Interval (Off, Very Small, Small, Medium, Large, Very Large) Show Scale Slider (OFF, ON) Tide/Current Icons Size (50 - 150(%), 100) NavData Transparency (0 - 80(%), 10) PhotoFusion Transparency (0 - 80(%), 15) Tide Range for PhotoFusion (0.0 - 60(ft), 0) Tidal Currents Transparency (0 - 80(%), 25) Radar Transparency (0 - 80(%), 20) Range Link (ON, OFF)
Page 262
APPENDIX 1 MENU TREE S-52 S-52 Vector Chart Display Mode (Custom, Base, Standard, Other, Fishing) Display Unknown Object (ON, OFF) Chart Data Coverage (ON, OFF) Water and Seabed Features (ON, OFF) Traffic Routes (ON, OFF) Information Areas (ON, OFF) Buoys & Beacons (ON, OFF) Lights (ON, OFF) Fog Signals (ON, OFF) Radar (ON, OFF)
Page 263
APPENDIX 1 MENU TREE Weather Load Weather File (Open the dialog box to select the weather file to load.) Weather Data Server (NavCenter, Sirius) Sirius Weather Radar (USNowRadar, CanadianRadar) Zone Forecast (BBWX3 only) Marine Warnings (BBWX3 only) Tropical Infos (BBWX3 only) Sirius Diagnostic (BBWX3 only) Tidal Step (5’00s, 10’00s, 15’00s, 20’00s, 30’00s, 1h00’, 2h00’, 3h00’, 6h00’, 12h00’) Duration of Animation (0’05s, 0’10s, 0’15s, 0’20s, 0’30s, 0’45 s, 1’00s, 2’00s, 3’00s)
Page 264
APPENDIX 1 MENU TREE Radar Radar Source (Select the antenna host name.) Day Background Color (Black, Dark Blue, White) Night Background Color (Black, Dark Blue) Echo Color (Multicolor, Green, Yellow) Rings Interval (Auto, 1, 2, 3, 4, 5, 6, 7, 8, 9) Show Range Slider (ON, OFF) Own Ship Icon (ON, OFF) Bearing Scale Mode (Relative, True)
Page 265
APPENDIX 1 MENU TREE Sounder Fish Finder Source (TZTL, network sounder name if connected) Day Background Color (White, Light Blue, Black, Dark Blue) Night Background Color (Black, Dark Blue) Echo Color Levels (8 Colors, 16 Colors, 64 Colors) Show Range Slider (ON, OFF) A-Scope Peak Hold (ON, OFF) Zoom Reference Lines (ON, OFF) Smoothing (ON, OFF)
Page 266
APPENDIX 1 MENU TREE Alarm Hardware Alarm (ON, OFF) XTE Alarm (ON, OFF) Depth Alarm (ON, OFF) Depth Alarm Value (0 - 900(ft), 30) Sea Surface Temperature Alarm (Off, Over, Under, Within, Out of) °F Temperature Alarm Value (32 - 140( ), 70.00) °F Temp.
Page 267
APPENDIX 1 MENU TREE Camera VIDEO INPUT 1 Connected (ON, OFF) NickName (Camera 1) VIDEO INPUT 2 Connected (ON, OFF) NickName (Camera 2) CONTROLLABLE CAMERA FLIR Installation Scan IP FLIR IP Video Source (None, Camera 1, Camera 2) ° Camera Offset (Right-left) (0 °...
Page 268
APPENDIX 1 MENU TREE IF NMEAFI SETUP Select IF DATA ACQUISITION GP330B WAAS Mode WS200 WAAS Mode Data Source Sensor List NMEA 0183 Output NMEA 2000 PGN Output Sky View INTERNAL GPS SETUP WAAS Mode SC-30 SETUP WAAS Mode Heading Offset Pitch Offset Roll Offset CALIBRATION...
APPENDIX 2 RADIO REGULATORY INFORMATION Wireless Interoperability This product is designed to be interoperable with any wireless LAN product that is based on direct sequence spread spectrum (DSSS) and orthogonal frequency division multiplexing (OFDM) radio technology and to comply with the following standards. •...
Page 270
APPENDIX 2 RADIO REGULATORY INFORMATION USA-Federal Communications Commission (FCC) Below are descriptions for built-in Wireless LAN module. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Page 271
APPENDIX 2 RADIO REGULATORY INFORMATION Canada-Industry Canada (IC) Below are descriptions for built-in Wireless LAN module. This device complies with RSS 210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired op- eration of this device.
Page 275
INDEX vector charts text and object information........2-10 False echo viewing ..........13-10 fish finder..........7-24 zoom in, zoom out........2-2 False echoes Clutter (fish finder) ........7-7 radar............6-22 Controls............1-2 Fan replacement ........14-2 CPA graphic display FAX-30 (Facsimile Receiver) setup ..13-8 AIS ............12-9 File format ..........8-1 radar............6-31 Fish alarm CPA/TCPA alarm ......
Page 276
INDEX split screen ..........10-5 default settings ........4-4 steering ..........10-2 deleting............ 4-6 switching between displays ....10-9 deleting all ..........4-6 theme ..........10-16 editing from points list......4-8 Interference editing on screen ........4-7 fish finder..........7-9 entering on plotter display .......
Page 277
INDEX creating from points........5-3 Sirius radio creating from points list ......5-4 controls........11-13 11-14 creating on plotter screen......5-2 enabling........11-12 11-13 creating with current track ......2-22 Sirius weather creating with past track ......2-21 advanced Wx data .........11-7 deleting.............5-9 animation radar ........11-8 deleting points or route points ....5-5 data availability........11-9 description..........5-1...
Page 278
INDEX Tuning ............6-1 TVG............7-10 TX pulse (fish finder) ....... 7-19 TX/Standby switch ........6-1 Units menu ..........13-2 Vector charts text and objects....2-10 Virtual image ........... 6-23 range measurement with....6-8 Watchman ..........6-14 Waypoint arrival notification ....5-14 Waypoint switching mode .......
Need help?
Do you have a question about the TZTL12F and is the answer not in the manual?
Questions and answers