Page 1
DHCE 6/50, 8/50 English Instantaneous water heater - Operation and installation instructions This water heater must be installed (water and electrical installation), commissioned and serviced by approved service technicians in accordance with these instructions.
- Children should be supervised to ensure that they do not play with the appliance. STIEBEL ELTRON...
Page 3
• ➝ temperature of ~ 40 ํ Description of the unit (External) Fig. 1 1.3 Description of the unit (External) a. Indicator Light c. Hot Water Outlet Pipe b. Temperature Control knob d. Cold Water Inlet Pipe STIEBEL ELTRON...
Page 4
Please contact wall (water connection downwards). the Stiebel Eltron Service Centre for further inspections and repairs to be made. Warning : Call 1800 153 351 (Australia).
Page 5
(Fig. 2, No.12). The hot water temperature depends on the power of the unit, the cold water temperature and the flow volume. STIEBEL ELTRON...
Operation Instruction for the user and the qualified installer 3. Technical Data Type DHCE 6/50 DHCE 8/50 Norminal capacity 0.45 Design Close outlet Max. water pressure 1000 kPa Min. water pressure to activate unit 200 kPa Water connection G ½“ (External thread) (15mm)
Page 7
/ or your country. unauthorized installers. The installation, electrical connection and first operation of this appliance should be carried out by a qualified installer. STIEBEL ELTRON...
Page 8
- Increase flow volume through the unit. required for the unit to turn it on has not been reached. - Water flow too high - Reduce water flow - Heating setting too low - Turn knob to the right (max. position) STIEBEL ELTRON...
10. Cold water connection 4. Distance of the connection 11. Hot water connection cable (Fig. 5 No.4) 12. Flow Limiter 5. Thermostat 13. Circuit board cover 6. Cable entry with seal Description of the unit (Internal) Fig. 2 STIEBEL ELTRON...
Page 10
Installation Instruction for the qualified installer Installation to a bath / sink. Fig. 3 Dimension Cable 65 mm G1/2 100 mm 35 mm 110 mm. 200 mm Fig. 4 Fig. 5 STIEBEL ELTRON...
Page 11
C - Control Triac set D - Thermal cut-out 4 x 35 mm E - Temperature Sensor (Inlet) 6 mm F - Temperature Sensor (Outlet) Fig. 6 Fig. 7 Wall Mounting 4 x 35 mm 4,3 mm Fig. 8 STIEBEL ELTRON...
Page 12
- Create an opening for the water - Remove the screw from underneath inlet in the case of wall-embeded and the water heater to open the cover of the wall-mounted pipes. unit. (concealed connection) Fig. 10 Fig. 12 STIEBEL ELTRON...
Page 13
- Insert the wires into the respective openings according to the diagram, and fasten the screws to secure the wires tightly. Please en- sure that the correct size of wire is used. STIEBEL ELTRON...
Page 14
The cold water pipe must be turned to the joints (both hot and cold water), using a on in order to rinse it before rubber leakage gasket (Fig. 17/C) between installation. Pressure-resistant equipment the joints. must be used in compliance with accepted standards. STIEBEL ELTRON...
Page 15
Installation Instruction for the qualified installer - Install the cover. Connect the power - After installation is complete, close cord between the circuit board and the cover. the casing and screw in tightly. Fig. 21 Fig. 19 Fig. 20 STIEBEL ELTRON...
Page 16
Who gives the warranty 9.3. The name, address and contact details (such as 1. The warranty is given by Stiebel Eltron (Aust) Pty Ltd (A.B.N. phone number and e-mail address) of the owner; 82 066 271 083) of 6 Prohasky Street, Port Melbourne, Victoria, 3207 (“we”, “us”...
Page 17
(f) foreign matter in the water supply, such as sludge or sediment; 19. The Stiebel Eltron warranty for the unit is in addition to any rights and remedies you may have under the Australian (g) corrosive elements in the water supply;...
Need help?
Do you have a question about the DHCE 6/50 and is the answer not in the manual?
Questions and answers