Related Manuals for Hitachi PC-ALHP1
Summary of Contents for Hitachi PC-ALHP1
- Page 1 INSTALLATION AND OPERATION MANUAL WIRELESS RECEIVER KIT PC-ALHP1 TIMER FILTER DEF EMERGENCY HEAT COOL...
- Page 3 Specifications in this manual are subject to change without notice in order that HITACHI may bring the latest innovations to their customers. Whilst every effort is made to ensure that all specifications are correct, printing errors are beyond Hitachi’s control; Hitachi can-...
- Page 4 C A U T I O N This product shall not be mixed with general house waste at the end of its life and it shall be retired according to the appropria- ted local or national regulations in a environmentally correct way. Due to the refrigerant, oil and other components contained in Air Conditioner, its dismantling must be done by a professional installer according to the applicable regulations.
- Page 5 DANGER – Hazards or unsafe practices which COULD result in severe personal injuries or death. CAUTION – Hazards or unsafe practices which COULD result in minor personal injury or product or property damage. NOTE – The text following this symbol contains information or instructions that may be of use or that require a more thorough explanation.
-
Page 6: Table Of Contents
INDEX NDICE Í 1. SAFETY SUMMARY 1. RESUMEN DE SEGURIDAD 2. BEFORE INSTALLATION AND OPERATION 2. ANTES DE LA INSTALACIÓN Y EL FUNCIONAMIENTO 3. NAME OF PARTS 3. NOMBRE DE LAS PARTES 4. INSTALLATION 4. INSTALACIÓN 5. OPERATION 5. FUNCIONAMIENTO 6. - Page 7 INDHOLDSFORTEGNELSE INHOUDSOPGAVE 1. OVERSIGT OVER SIKKERHED 1. VEILIGHEIDSSAMENVATTING 2. FØR MONTERING OG IBRUGTAGNING 2. VÓÓR DE INSTALLATIE EN BEDIENING 3. NAVN PÅ DELE 3. NAMEN VAN ONDERDELEN 4. MONTERING 4. INSTALLATIE 5. DRIFT 5. BEDIENING 6. VALGFRI FUNKTIONER 6. OPTIONELE FUNCTIES 7.
-
Page 9: Safety Summary
DO NOT install the indoor unit, outdoor unit, controller and • Important: read and understand this manual before using this cable within approximately 3 meters from strong electro- remote controller. magnetic wave radiators such as medical equipment. In case that the controller is installed in a place where there is elec- If you have any questions, contact your HITACHI distributor or tromagnetic wave radiation, shield the controller and cables dealer. by covering with the steel box and running the cable through the metal conduit tube. • In case that there is electric noise at the power source for the indoor unit, provide a noise filter. -
Page 10: Name Of Parts
Name of parts 3 NAME OF PARTS WARNING Label Indoor unit Air outlet Louver Air inlet grille Indication place for indoor unit model (The air filter is attached inside) It is indicated in the specification plate attached at the drain pan. (Check it by opening the air inlet grille.) Receiver Dip switch... -
Page 11: Installation
Installation 4 INSTALLATION C A U T I O N D A N G E R • When the receiver kit is attached near lighting which gene- • Turn OFF the power source completely before perfor- rates the ambient light, it may not receive the signal from the ming the dip switch setting, installation work and elec- wireless remote control. Pay attention to the installation posi- trical wiring work for receiver kit. If not, it may cause an tion of receiver kit. - Page 12 Installation b. Press the service hole to remove the remote control switch cover. Press here by screwdriver or a stick to remove the remote control switch cover 2 Remote Control Switch Covers Position for Receiver Kit (It can be attached to both of right side and left side) 5 Attach the receiver kit to the lower cover.
-
Page 13: Operation
Operation 7 Remove the electrical box cover. Connect the connecting cable to the terminals A and B at the terminal board for remote control switch as following figure. (There are no polarity between terminals A and B.) Electrical Box Terminal Board for Remote Connecting Cable for R Control Switch Printed Circuit Board (PCB1) -
Page 14: Installation
Operation N O T E After the heating operation is stopped, the fan mode may be ope- COOL rated for approximately 2 minutes. The indications of setting temperature, fan speed and air flow angle are turned OFF. 5.2 OPERATION MODE (COOLING, HEATING, DRY, AUTOMATIC COOLING/HEATING AND FAN OPERATION) Function • Cooling operation (COOL): to decrease the room tempera- N O T E ture. - Page 15 Operation Air flow direction : Auto swing operation will be started. At this time, the louver Point the transmitter towards the receiver kit and press “LO- will swing repeatedly on LCD. UVER” switch to set the louver angle. N O T E °C •...
- Page 16 Operation Function • When the “MODE” switch is pressed at “AUTO”, the fan ope- Automatic cooling/heating operation is automatically switched ration is started. cooling and heating based on the set temperature as following Point the transmitter towards the receiver kit and press “RUN/ inlet air temperature conditions. STOP” switch. When the transmitting indication “ “...
-
Page 17: Emergency Operation
Operation Cancel setting Point the transmitter towards the receiver kit and press “SET” switch. The TIMER indicator (green) on receiver is turned ON. To cancel the timer setting, point the transmitter towards the receiver kit and press “CANCEL” switch. The TIMER indicator (green) on receiver is turned OFF. - Page 18 Optional functions 6 OPTIONAL FUNCTIONS D A N G E R Turn OFF the power source completely before performing the dip switch setting for receiver kit. If not, it may cause an elec- tric shock. The following switches are on the receiver kit. Dip switch (DSW1) (Factory-setting) Cover Rear side of receiver kit The dip switch (DSW1) is for the optional function selection. If the optional function selection is required, set the dip switch as follows. Dip switch setting (DSW1) Optional function Details...
- Page 19 7.1 HORIZONTAL DISTANCE LIMIT FOR RECEIVER KIT Horizontal distance limit for receiver kit (in the case that height of Receiver kit wireless remote control from floor is 1 m): (Model: PC-ALHP1) Ceiling Height of indoor unit Horizontal distance Indoor unit (air panel)
- Page 20 Identifying indoor units installed side by side operation 8 IDENTIFYING INDOOR UNITS INSTALLED SIDE BY SIDE OPERATION C A U T I O N Turn OFF the power source completely before performing the dip switch setting for receiver kit. If not, it may cause an electric shock. Setting of identifying of indoor units installed side by Cancellation of identifying of indoor units installed side side by side 1 Receiver kit setting...
- Page 21 Indication of receiver kit Periodic check (only for gas heat pump air conditioner) For the gas heat pump air conditioning, the periodic check is re- quired because the engine is equipped. If the indication lamp flashes in follows, the periodic check shall be performed.
- Page 24 PMML0314A rev.0 - 09/2013 - P5415315 Printed in Japan...