Technical Data - Philips 200P7ES/00 Service Manual

ELECTRICAL SPECIFICATION
1. General
1.1. Product description
"
The Hudson7 20.1 TFT flat panel monitor is specified as a
display peripheral with Analog video signal input, Digital video
"
input ,input 20.1 TFT LCD display.
Horizontal scan range is 30 - 98 K Hz and refresh range is
56 - 85 Hz. This scan range allows it to display resolution up to
1600*1200 non-interlaced at75 Hz refresh rate. The image can
be adjust through OSD control, these adjustments can be stored
on an board memory including 34 preset modes
and 13 factory preset modes.
All optical characteristics (including WHITE-D, Brightness, and so
on) are determined according to panel specification after warming
up approximate 30 minutes that brightness stability is optimal, and
follow strictly after panel specification.
1.2 Destination : US*.CA*. Z9
1.3. Basic data
1.3.1 LCD panel : LPL
Type NR.
Outside dimensions
Pitch ( mm )
Color pixel arrangement
Display surface : low reflection, antiglare with hard coating
Color depth
Backlight
Active area(WxH)
View angle : Horizontal & Vertical 178 degree (Typ)
Contrast ratio
White luminance: Panel original color >250nits (min), 300 nits (Typ.)
LCD panel : AUO
Type NR.
Outside dimensions : 432.0(w)*331.4(h)*23.1(d) (Typ) mm
Pitch ( mm )
Color pixel arrangement
Display surface : low reflection, antiglare with hard coating
Color depth
Backlight
Active area(WxH)
View angle
Contrast ratio
White luminance: Panel original color >200nits (min), 250 nits (Typ.)
1.3.2. Power supply
Main voltage : AC 90 - 135 Vrms and 170 - 264 Vrms, 50/60±2 Hz
Power cord length : 1.8M
Power cord type : 3 lead with earth plug
Power indicator : LED (ON: blue, Standby: amber, NEW MODE:
flashing blue twice per second before user adjust and save it.).
Auto power saving : EPA, Nutek, VESA DPMS
Mode HSYNC VSYNC Video
Power-On On On active
Power-On On On active
Off Off On blanked
Off On Off blanked
Off Off Off blanked
DC Power N/A
Off
1.3.3. Horizontal scan : 30 - 98 KHz
1.3.4. Vertical scan : 56 - 85 Hz
1.3.5. Input signals
1.Signal input level
Video : 0.7 Vp-p Linear / 75 ohms
Sync : H/H+V, V TTL level, composite sync, sync on green
Impedance
Video : Terminated with 75 ohms
Sync : Terminated with 2K2 ohms

Technical Data

: LM201U04 (LG.PHILIPS)
: 432.0(w)*331.5(h)*25(d) (Typ) mm
: 0.255 (per one triad) x 0.-255mm
: RGB vertical stripes
: 16777216 colors (8 bits)
: Six CCFL s '
"
: 408x306mm (20.1 diagonal)
: 700:1 (Typ) ; 400:1 (Min)
: M201UN02 (AUO)
: 0.255 (per one triad) x 0.-255mm
: RGB vertical stripes
: 16777216 colors (8 bits)
'
: Six CCFL s
"
: 408x306mm (20.1 diagonal)
: Horizontal & Vertical 170 degree (Typ)
: 700:1 (Typ) ; 400:1 (Min)
Pwr-cons. Indication Rec. time
< 60 W Blue LED Without USB
< 70 W Blue LED With USB
< 2W Amber LED < 3 s
< 2 W Amber LED < 3 s
< 2 W Amber LED < 3 s
< 1W LED Off
The input signals can be applied in two different modes :
1).VESA Analog
Input signal : Video, Hsync., Vsync
Video : 0.7 Vp-p, input impedance, 75 ohm @DC
Sync. : Separate sync
2). Input DVI Digital
Input signal : Four channel TMDS signals
1.3.6 Input connectors (1) Input analog D-sub connector pin assignment
PIN No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
(2) Input DVI-I connector pin assignment
Note the mark * for DVI-I to Dsub only " "
Pin No.
1 TMDS data2-
2 TMDS data2+
3 TMDS data2 shield
4 NC
5 NC
6 DDC clock
7 DDC data
8 * Analog V-sync
9 TMDS data1-
10 TMDS data1+
11 TMDS data1 shield
12 NC
13 NC
14 +5V
15 Ground(return for +5V and H/V-sync)
16 Hot plug detect
17 TMDS data0-
18 TMDS data0+
19 TMDS data0 shield
200P7 LCD
Go to cover page
TTL level , input impedance 5k ohms
Hor. sync Positive/Negative
Ver. sync Positive/Negative
SIGNAL
Red
Green/ SOG
Blue
Sense (GND)
Cable detect (GND)
Red GND
Green GND
Blue GND
DDC +5V
GND
Sense (GND)
Bi-directional data
H/H+V sync
V-sync
Data clock
Description
3