2. When the cover is open, close viewing through the objective lens with the naked eye will cause exposure to the laser beam. ∗ : See page 48. [LF type] (Printed on the Rear Panel) [RR type] [RL/NC, RD/RB and LF types] [BK type] DV-366-S...
Page 3
By following the instructions in this manual, be sure to apply the prescribed grease or glue to proper portions by the appropriate amount.For replacement parts or tools, the prescribed ones should be used. DV-366-S...
7.1.7 ID NUMBER AND ID DATA SETTING....................61 7.1.8 SEQUENCE AFTER POWER ON ......................64 7.1.9 DISASSEMBLY ............................. 65 7.2 IC ................................72 7.3 DISC / CONTENT FORMAT PLAYBACK COMPATIBILITY ..............86 7.4 CLEANING............................... 89 8. PANEL FACILITIES ............................90 DV-366-S...
Wow and flutter..Limit of measurement Dimensions: (±0.001% W. PEAK) or lower DV-366-s..420 (W) x 55 (H) x 283 (D) mm Operating temperature ..+5°C to +35°C Digital output Operating humidity .
For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions, apply as you think it appropriate.) 2.1 PACKING RRXU Type Only LFXJ Type Only RLXJ/NC, RRXU Type Only RDXJ/RB, BKXJ LFXJ Types Only 7- 11 "Operating Instructions" DV-366-S...
Page 7
Label See Contrast table (2) Operating Instructions See Contrast table (2) (Arabic) (2) CONTRAST TABLE DV-366-S/RRXU, RLXJ/NC, RDXJ/RB, BKXJ and LFXJ are constructed the same except for the following : DV-366-S/RLXJ/ DV-366-S/RDXJ/ Mark No. Symbol and Description DV-366-S/RRXU DV-366-S/BKXJ DV-366-S/LFXJ >...
2.2 EXTERIOR SECTION Refer to "2.4 LOADING MECHA. ASSY". Refer to "2.3 FRONT PANEL SECTION". DV-366-S...
Page 9
See Contrast table (2) Rear Panel See Contrast table (2) PCB Base See Contrast table (2) (2) CONTRAST TABLE DV-366-S/RRXU, RLXJ/NC, RDXJ/RB, BKXJ and LFXJ are constructed the same except for the following : DV-366-S/RLXJ/ DV-366-S/RDXJ/ Mark No. Symbol and Description DV-366-S/RRXU...
Page 11
Connector Assy PF03PP-B07 FP Angle See Contrast table (2) Rubber Foot VEB1349 (2) CONTRAST TABLE DV-366-S/RRXU, RLXJ/NC, RDXJ/RB, BKXJ and LFXJ are constructed the same except for the following : DV-366-S/RLXJ/ DV-366-S/RDXJ/ Mark No. Symbol and Description DV-366-S/RRXU DV-366-S/BKXJ DV-366-S/LFXJ...
JGZ17P028FMC Screw Z39-019 Flexible Cable (24P) VDA1945 Tray VNL1920 Connector Assy 2P VKP2253 Floating Rubber VEB1351 Belt VEB1330 Stabilizer VNE2253 Loading Base VNL1917 Float Base DVD VNL1918 Drive Cam VNL1919 Gear Pulley VNL1921 Loading Gear VNL1922 Drive Gear VNL1923 DV-366-S...
Page 13
Rear View Daifree Daifree No. 23 No. 23 GEM1036 GEM1036 Tray Tray Concave of unevenness Concave of unevenness Inner side of a ditch Daifree GEM1036 Top View Bottom View Side of the rib Concave of unevenness Daifree Daifree GEM1036 GEM1036 DV-366-S...
Note : When ordering service parts, be sure to refer to "EXPLODED VIEWS and PARTS LIST" or "PCB PARTS LIST". POWER SUPPLY UNIT (VWR1366) ( or VWR1368) DVDM ASSY (LFXJ Type: VWS1554) (Other Types: VWS1555) LFXJ Type Only CN101 DOUT ASSY (VWV1937) DV-366-S...
Page 21
: TRACKING SERVO LOOP LINE : STEPPING SERVO LOOP LINE KEY0 PWSB ASSY FLKY ASSY (VWG2424) (LFXJ Type: VWG2420) (Other Types: VWG2421) PICKUP ASSY-S (OXX8005) SPINDLE STEPPING MOTOR MOTOR : VXM1101 : VXM1099 LOADING MOTOR ASSY : VXX2872 LOAB ASSY (VWG2426) DV-366-S...
3.5 DVDM ASSY 2/3 [BACK END BLOCK] DVDM ASSY (LFXJ Type: VWS1554) VYW2109 (Other Types: VWS1555) B/Cb R/Cr LFXJ Type Only DV-366-S...
Page 25
: V SIGNAL ROUTE : S-VIDEO OUT C SIGNAL ROUTE B/Cb : S-VIDEO OUT Y SIGNAL ROUTE : R/Cr SIGNAL ROUTE R/Cr : G/Y SIGNAL ROUTE : B/Cb SIGNAL ROUTE B/Cb : AUDIO SIGNAL ROUTE : AUDIO(DIGITAL) SIGNAL ROUTE DV-366-S...
3.6 DVDM ASSY 3/3 [AUDIO/VIDEO BLOCK] AUDIO DAC MM1623AF B/Cb B/Cb R/Cr R/Cr VIDEO DRIVER LFXJ Type Only DVDM ASSY (LFXJ Type: VWS1554) (Other Types: VWS1555) DV-366-S...
Page 27
: V SIGNAL ROUTE : S-VIDEO OUT C SIGNAL ROUTE : S-VIDEO OUT Y SIGNAL ROUTE : R/Cr SIGNAL ROUTE R/Cr B/Cb : G/Y SIGNAL ROUTE R/Cr CN101 : B/Cb SIGNAL ROUTE B/Cb : AUDIO SIGNAL ROUTE : AUDIO(DIGITAL) SIGNAL ROUTE DV-366-S...
SIDE B Chip Part P.C.Board transistor Resistor array 3-terminal regulator SIDE A SIDE B LOAB ASSY (VNP1910-A) LOAB S101 LOAD+ VWG2426- CN602 CN602 C102 LOAD- PYKC F6 VNP1910- C101 CN601 CN601 CN602 CN601 CN601 CN602 CN103 LOADING MOTOR ASSY DV-366-S...
CONTAINS LEAD IN SOLDER AND CERTAIN ELECTRICAL PARTS WARNING CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM. IC101 IC301 IC400 IC404 IC603 IC604 IC403 IC601 IC602 Q403 Q390 Q211 Q201 Q202 Q405 Q402 Q603 Q212 Q404 Q401 DV-366-S...
4.3 FLKY and PWSB ASSYS SIDE A FLKY ASSY (VNP1901-B) CN102 D102 D101 PYKC F4X S102 FL DIM D104 S104 >> S103 FL101 << PWSB ASSY (VNP1901-B) SIDE B PWSB ASSY (VNP1901-B) C154 R138 PWSB VWG2424- CN103 VWG2425- FLKY ASSY (VNP1901-B) DV-366-S...
Page 39
VWG2422- VWG2423- TOP MENU S108 EJECT IR101 /STOP VNP1901- /PLAY S110 S117 S118 S119 DC FC PLAY/>> PAUSE/<< DOWN RETURN S107 S106 C101 HOME MENU/PAUSE STOP/EJECT CN101 CN104 S105 CN101 CN105 SIDE B CN101 C N 1 0 1 DV-366-S...
4.6 DOUT ASSY SIDE A SIDE A CN102 VWV1937- DOUT C151 C201 C251 GNDV GNDV GNDV PYKC-F4 ASPECT P/IX VNP1909- DOUT ASSY (VNP1909-A) SIDE B SIDE B DV-366-S...
[Electrical Part] screw screw Electrical adjustments are not required. 6.2 JIGS AND MEASURING INSTRUMENTS Test mode remote control Screwdriver (large) Screwdriver (medium) TV monitor unit (GGF1067) Screw tight (GYL1001) DVD test disc Precise screwdriver Soldering iron (GGV1025) DV-366-S...
Purpose: To set the sweep which was correct with the individual Traverse mechanism. Be sure to perform the following step finally when replaced Pickup, Traverse Mechanism and Spindle Motor. CLEAR GGF1067 Test mode remote control unit (It is necessary when performed adjustment procedure Ÿ.) DV-366-S...
Perform only trace, video and audio outputs are nothing. < When playback with the target address of disc (DVD)> For example, when playback with # 30000 During PLAY CHP/TIM Press keys in order 030000 TEST MODE: OFF POWER GGF1067 Test mode remote control unit DV-366-S...
(Refer to "6.1 ADJUSTMENT ITEMS AND LOCATION".) Spacer for Height adjustment Note: Turn a flat side Before removing the flexible cable for the into bottom pickup, soldering of the pickup circuit is necessary. For details, see "7.1.9 DISASSEMBLY". DV-366-S...
Page 50
J : Min If error rate is OK, Disc playback normally. locks a root of • The measurement of block error rate tangential and radial adjustment screws with the Screw tight, and go to step Screw tight: GYL1001 Test mode end DV-366-S...
Page 51
Initialize the Focus Sweep Setting Purpose: To set the sweep which was correct with the individual Traverse mechanism. Turn on the Player POWER CLEAR Note: Be sure to perform this step when replaced the Pickup or Traverse mechanism. DV-366-S...
Perform only trace, video and audio outputs are nothing. = Screen display ON/OFF 1. Turn off the display by pressing the [AUDIO] (A8-1E) key of the remote control unit. 2. Turn on the display by pressing the [DISPLAY] (A8-43) key of the remote control unit. DV-366-S...
Page 53
• After the search, perform only trace and video and audio outputs are nothing. 4. Release the Search address input • Clear the address by pressing the [CLEAR] (A8-45) key. Release the address input mode when pressing the [CLEAR] key once again. DV-366-S...
Kinds of version / firmware of the FE. Scart terminal output [SK – ∗ ∗] RAM or ROM (Display only the WY model which can do the output setting of scart terminal.) VIDEO : [00] S-VIDEO : [01] : [02] DV-366-S...
• Region confirmation mode (ESC + AUDIO [Test mode remote control unit] + "1"-"8" [Test mode remote control unit] keys) After you press the AUDIO key while holding the ESC key pressed and then input the region number, if the number is different from that set in the unit, an error message is displayed, and the tray opens. DV-366-S...
(version of ST core software) softwareVersion . softwareRevision / buildNumber 0 F.E VERSION Version of FRONT END (version of mechanism controller CHIP software) MainVersion / Kinds of firmware RAM or ROM - Remote control code = Key code of Main unit DV-366-S...
PLL lost timeout 0x93 DECODER ERROR 0xa∗ DECODER TIMEOUT 0xb∗ Note : 0 x & & ID lost error 0xa3 ID lost timeout 0xb3 DEVICE ERROR 0xd∗ code SRAM error 0xd1 (Only this part is displayed to a display) DV-366-S...
Do move to inner and outer periphery 1. Stepping motor of the stepping in the test mode? 2. Inside switch Stepping move timeout 0 x 54 Did timeout at stepping movement Do indicate "S-04" at the most inner 3. Driver periphery of the stepping? DV-366-S...
Page 60
SRAM error 0 x d1 Cannot access SRAM 2. Front End IC Is not bus line short-circuiting? 3. Front End-SRAM bus line FAILSAFE (0 x e∗) 1. software runaway Unexpected error 0 x e1 Unexpected error 3. Software bug DV-366-S...
(The SEARCH key is not accepted after all 9 digits have been entered.) Input ID Number ! [Player's ID Number Setting] ID Number ? > 0 0 0 0 0 0 0 0 1 OK ? <PLAY> Compare Mode <SEARCH> Enter Input ID Number ! DV-366-S...
Page 62
[Player's ID Number Setting] ID Number ? [ 0 0 0 0 0 0 0 0 1 ] Compare > 0 0 0 0 0 0 0 0 1 OK? <PLAY> Enter <STOP> Memory Clear Input ID Number ! DV-366-S...
Page 63
Insert The ID Data Disc ! If no ID data are set after the ID number is changed, the message "NO ID DATA" flashes on the screen and FL display for a few seconds after the power is turned on or during Stop mode. DV-366-S...
BACK END (FP_XRDY) [BACK END] Outputs the communicable signal to FL controller (FP_ACK) BACK END – FL controller communication The opening picture appears [FRONT END] Check the following: • Slider positioning (INSIDE SW) • Spindle FG stop Disc detection (Focus control) DV-366-S...
Gear in the Loading Mecha. Assy in the direction of the arrow, as indicated in the photo. If the Tray pops out a little, fully pull it out by hand. Screwdriver (small) Projection Slit Drive Gear Loading Mecha.Assy Tray open Screwdriver (small) DV-366-S...
Page 66
Remove the six hooks. Remove the front panel section. ×2 DVDM Assy 1 1 1 Remove the four screws. Remove the three screws. ×3 DVDM Assy DVDM Assy Remove the DVDM Assy and stand it against the other parts. DV-366-S...
Page 67
Mecha. Assy to the unit. Bridge Tray Drive Cam Note when reinserting the Tray When reinserting the Tray, first align the triangle printed on the Loading Base and the pin of the Drive Cam, then insert the Tray. Front Side Loading Base Triangle DV-366-S...
Page 68
Dislodge the flexible cables from their factory for the spindle motor Front Side placement. Flexible cable Flexible cable for the pickup for the stepping motor Bottom View Remove the four hooks. Traverse Mecha. Assy-S × 2 Remove the Traverse Mecha. Assy-S. × 2 DV-366-S...
Page 69
Remove the flexible cable for the pickup. Flexible cable for the pickup Bottom View Adjustment screw Adjustment screw Remove the two adjustment screws and two adjustment springs. (Skew screw) (Skew screw) Remove the Pickup Assy-S. Pickup Assy-S Adjustment spring (Skew spring) Adjustment spring (Skew spring) DV-366-S...
Page 70
Joint Spring Silicone Adhesive GEM1037 Joint 03 Silicone Adhesive GEM1037 Arrangement of the flexible cable Arrangement of the flexible cable for the spindle motor for the stepping motor : Conductive surface : Conductive surface Hook Hook Bottom View Bottom View DV-366-S...
Page 71
Reference line Hook Fold the flexible cable as indicated in the photo. Fold the flexible cable along the hook. Hook the part folded in Step 1 to the hook. Reference Hook Pass the cable below the hook line Hook DV-366-S...
Page 72
• The information shown in the list is basic information and may not correspond exactly to that shown in the schematic diagrams. • List of IC STM6316ATXXA, STM5589CVA, M63108FP, PE5374A 7 STM6316ATXXA (DVDM ASSY : IC301) • FRONT END IC ¶ Block Diagram DV-366-S...
Page 73
¶ Pin Function t i c t i c t s i t s i t s i t s i t s i t i s t i s DV-366-S...
Page 74
- t l l i c y t i - t l l i c y t i - t l l i c y t i d l l DV-366-S...
Page 84
Destination (of player) Select (Set with a combinaition of this 3 ports) MS1_0 H" : No System Reset mode , "L" : General mode H" : OEM Model , "L" : Pioneer Model MIC IN Detection of Microphone "H" : Microphone connected CHECKER H"...
Other formats, including but not limited to the • This unit will play DVD-RW discs recorded following, are not playable in this player: using the Video Recording (VR) format. • DVD-RW shows in the display when a VR format DVD-RW disc is loading. DV-366-S...
Page 87
Rights Management) copy protection will not play and the message Can’t play this format will be displayed (NO PLAY in the front panel display). The Windows Media™ logo printed on the box indicates that this player can playback WMA data. DV-366-S...
Page 88
Audio encoded at 128Kbps should sound close to regular CD Audio quality. This player will play lower bit-rate files, but please note that the sound quality becomes noticeably worse at lower bit-rates. DV-366-S...
7.4 CLEANING Before shipping out the product, be sure to clean the following positions by using the prescribed cleaning tools: Position to be cleaned Cleaning tools Pickup lenses Cleaning liquid : GEM1004 Cleaning paper : GED-008 DV-366-S...
8. PANEL FACILITIES DV-366-s STANDBY/ON 13 Remote control sensor Press to switch the player on or into standby. The remote control has a range of up to about FL DIMMER Press to dim or brighten the display. 14 Display See page 19 for a description of the display.
Page 91
DIGITAL AUDIO OUT – OPTICAL This is a digital audio output for connection to a PCM, Dolby Digital, DTS and/or MPEG- compatible AV receiver that has an optical digital input. Connect using a commercially available optical digital audio cable. DV-366-S...
Page 92
DV-366-s 8 and 3 REMAIN Indicates whether a disc is playing or paused. Indicates that the character display is showing the disc or title/chapter/track remain time. Indicates that the character display is showing a DVD chapter number. Character display TITLE...
Page 93
Press to pause playback; press again to restart. 12 PLAY MODE Press to display the Play Mode menu. (You can also get to the Play Mode menu by pressing HOME MENU and selecting Play Mode). DV-366-S...
Page 94
ENTER button in 6 above). 24 ZOOM 18 MENU Press to change the zoom level. Press to display a DVD disc menu, or the Disc Navigator if a VR format DVD-RW, CD, Video CD , MP3, WMA or JPEG disc is loaded. DV-366-S...