Page 1 DUSTER DRIVER’S HANDBOOK...
Page 2 Renault cars. Lasting protection and optimum performance for your engine – guaranteed. Whether changing the oil or simply topping up, to find the approved ELF lubricant best suited to your vehicle, ask your Renault dealer for a recommendation or consult your vehi- cle maintenance handbook.
Page 3: Driving
Welcome aboard your vehicle This Driver’s Handbook contains the information necessary: – for you to familiarise yourself with your vehicle, to use it to its best advantage and to benefit fully from the all the functions and the technical developments it incorporates. –...
Page 5: Table Of Contents
Sections Getting to know your vehicle ....... Driving ..............Your comfort ............Maintenance ............Practical advice ............ Technical specifications ........Alphabetical index ..........
Page 7 Section 1: Getting to know your vehicle Keys/radio frequency remote control: general information ....... . Locking/unlocking the doors .
Page 8: Keys/Radio Frequency Remote Control: General Information
KEYS, RADIO FREQUENCY REMOTE CONTROL: general information (1/2) Key A Radio frequency remote 4 Remote engine start-up. control B or C 1 Coded key for ignition switch, doors and fuel filler cap. 2 Locks all the opening elements. 3 Unlocks all the opening elements. Driver’s responsibility Never leave an animal, child or adult who is not self-sufficient alone in your vehicle, even for a short time.
Page 9 KEYS, RADIO FREQUENCY REMOTE CONTROL: general information (2/2) The remote control unit operating range This varies according to the environ- ment. It is therefore important when handling the remote control to ensure that you do not lock or unlock the vehi- cle by inadvertently pressing the but- Replacement and additional keys tons.
Page 10: Locking The Doors
RADIO FREQUENCY REMOTE CONTROL: use Locking the doors Press locking button 1. The hazard warning lights and side in- dicator lights flash twice to indicate that the doors have locked. If a door or the tailgate is open or not properly shut, the doors and tailgate lock then quickly unlock and the hazard warning lights and side indicator lights...
Page 11: Locking And Unlocking The Doors
LOCKING AND UNLOCKING THE DOORS (1/3) Manual locking Child safety From the outside To make it impossible for the rear doors Never leave your vehicle to be opened from the inside, move with the key or remote con- Unlock the doors using the remote con- lever 2 on each door and check from trol inside.
Page 12 LOCKING AND UNLOCKING THE DOORS (2/3) Electric central locking Depending on the vehicle, it can be used to simultaneously lock or unlock the four doors and the boot. Lock or unlock the doors by pressing switch 3. The front door mechanism cannot be locked if the door is open.
Page 13 LOCKING AND UNLOCKING THE DOORS (3/3) Locking the opening elements without the radio frequency remote control For example, in the event of a dis- charged battery or the radio frequency remote control temporarily not working. With the engine switched off and an opening element (door or boot) open, press and hold switch 3 for more than five seconds.
Page 14: Automatic Locking When Driving
AUTOMATIC LOCKING WHEN DRIVING Operating principle To deactivate Operating faults After the vehicle is started, the system With the ignition on, press and hold If you notice an operating fault (auto- automatically locks the doors once your switch 1 for approximately 5 seconds, matic locking impossible), first check speed reaches approximately 5 mph until you hear a beep.
Page 15: Opening And Closing The Doors
OPENING AND CLOSING THE DOORS (1/2) Opening from the outside Opening from the inside With the doors unlocked (refer to the Front: pull handle 3 information on “Locking/unlocking the Rear: from the inside, lift unlocking doors” in Section 1). button 2 and pull door handle 3. Front: place your hand behind handle 1 and pull it towards you..
Page 16 OPENING AND CLOSING THE DOORS (2/2) Lights-on reminder buzzer Driver’s responsibility If you have left the lights on after switch- when parking or stopping ing off the ignition, a warning buzzer will the vehicle sound when a front door is opened (to Never leave an animal, prevent the battery from discharging, child or adult who is not self-suffi-...
Page 17: Engine Immobiliser
ENGINE IMMOBILISER This prevents the vehicle being Operating faults driven by anyone not in possession After the ignition has been switched of the vehicle’s coded ignition key. on, if warning light 1 continues to flash or remains continuously lit, there is a Operating principle system operating fault.
Page 18: Front Headrests
FRONT HEADRESTS To raise the headrest Depending on the vehicle, lift the head- rest to its highest position. Press the button 2 or 3 and lift the headrest to release it (tilt the seatback backwards if necessary). To raise the headrest To refit the headrest Pull the headrest upwards.
Page 19: Front Seats
FRONT SEATS (1/2) To move forwards or For safety reasons, carry backwards out any adjustments when Lift bar 1 to release. Release the bar the vehicle is not being once the seat is in the correct position driven. and ensure that the seat is fully locked We would advise you not to recline into position.
Page 20 FRONT SEATS (2/2) Heated seats To adjust the lumbar support on the driver’s seat Depending on the vehicle, with the igni- tion on, press switch 7. Manoeuvre the stalk 8 to the desired position. The system, which has a thermostat, decides whether or not the heating is needed.
Page 21: Seat Belts
SEAT BELTS (1/5) Always wear your seat belt when trav- Before starting, adjust your driving elling in your vehicle. You must also position and then have each occu- comply with the legislation of the par- pant adjust their seat belt to ensure ticular country you are in.
Page 22: Seat Belt Reminder Light
SEAT BELTS (2/5) ß Seat belt reminder light Depending on the vehicle, it comes on when the engine is started and if the driver’s and/or passenger’s seat belt is not fastened. When the ve- hicle is being driven, it comes on and a beep sounds for approximately 2 min- utes until the driver’s seat belt is fas- tened.
Page 23 SEAT BELTS (3/5) Rear side seat belts Rear centre seat belt A (depending on vehicle) Slowly unwind belt 8 and click buckle 9 into red catch 10. Remove buckle 15 from its housing 16. Slowly unwind the belt 13 and click the buckle 15 into the black catch 14.
Page 24 SEAT BELTS (4/5) Rear lap belt with manual adjustment 17 The strap should be worn flat over your thighs and against your pelvis. The seat belt should be worn so that it is as close as possible to your body, i.e.: avoid wearing heavy clothing or keeping bulky objects under the belts, etc.
Page 25 SEAT BELTS (5/5) The following information applies to the vehicle’s front and rear seat belts. – No modification may be made to the component parts of the originally fitted restraint system: seat belts, seats and their mountings. For special operations (e.g. fitting child seats), contact an authorised dealer. –...
Page 26: Methods Of Restraint In Addition To The Front Seat Belts
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (1/3) Depending on the vehicle, they are – Have the entire restraint composed of: system checked following – seat belt pretensioners; an accident. – chest-level load limiters; – No operation whatsoever is permitted on any part of the –...
Page 27 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (2/3) Driver’s and passenger air Operation bags This system is only operational when the ignition is switched on. These may be fitted to the front seats on the driver and passenger side (loca- If a severe frontal impact occurs, the tion A).
Page 28 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (3/3) All of the warnings below are given so that the air bag is not obstructed in any way when it is deployed and also to pre- vent the risk of serious injuries caused by items which may be dislodged when the air bag deploys. Warnings concerning the driver’s air bag –...
Page 29: Side Protection Devices
SIDE PROTECTION DEVICES Side air bags These air bags may be fitted to the front seats and are deployed at the sides of the seats (door side) to protect the oc- cupants in the event of a severe side impact. Warnings concerning the side air bag –...
Page 30: Additional Methods Of Restraint
ADDITIONAL METHODS OF RESTRAINT All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. Operating faults The airbag is designed to complement the action of the seat belt.
Page 31: Child Safety: General Information
CHILD SAFETY: General information (1/2) Carrying children Children, and adults, must be correctly seated and strapped in for all journeys. The children being carried in your vehi- cle are your responsibility. A child is not a miniature adult. Children are at risk of specific injuries as their muscles and bones have not yet fin- ished growing.
Page 32 CHILD SAFETY: General information (2/2) Using a child seat Set a good example by always fas- The level of protection offered by the tening your seat belt and teaching child seat depends on its ability to re- your child: strain your child and on its installation. –...
Page 33 CHILD SAFETY: choosing a child seat Rear-facing child seats Forward-facing child seats Booster cushions A baby’s head is, proportionally, heavier The child’s head and abdomen need to From 15 kg or 4 years, the child can than that of an adult and its neck is very be protected as a priority.
Page 34: Child Seat Mounting
CHILD SAFETY: mounting a child seat (1/2) Attachment via the seat belt Attachment with the ISOFIX system The seat belt must be adjusted to Authorised ISOFIX child seats are ap- ensure that it is effective in the event of proved in accordance with regulation harsh braking or an impact.
Page 35 CHILD SAFETY: mounting a child seat (2/2) The rings ISOFIX 1 are located be- The third ring of each side seat is used Attach the hook on the belt to one of the tween the seatback and the seat base to attach the upper strap on some child rings 3 (4x2 version) or 4 (4x4 version).
Page 36: Fitting A Child Seat
CHILD SAFETY: fitting a child seat (1/6) Some seats are not suitable for fitting In the front seat child seats. The diagram on the fol- The laws concerning children travel- lowing page shows you how to attach ling in the front passenger seat differ in a child seat.
Page 37 CHILD SAFETY: fitting a child seat (2/6) In the rear side seat For the safety of the child in the Rear centre seat forward-facing seat, do not move the A carrycot can be installed across the A child seat may only be fitted in this seat in front back past the middle of the vehicle and will take up at least two seat if it is equipped with an inertia-reel...
Page 38 CHILD SAFETY: fitting a child seat (3/6) Vehicles without air bag OR with air bag deactivated Child seat attached using the ISOFIX mounting ü Seat which allows an ISOFIX child seat to be fitted. ± The rear seats are fitted with an anchorage point which allows a forward-facing ISOFIX child seat with universal approval to be fitted.
Page 39 CHILD SAFETY: fitting a child seat (4/6) Vehicles with passenger air bag not deactivated Child seat attached using the ISOFIX mounting ü Seat which allows an ISOFIX child seat to be fitted. ± The rear seats are fitted with an anchorage point which allows a forward-facing ISOFIX child seat with universal approval to be fitted.
Page 40 CHILD SAFETY: fitting a child seat (5/6) The table below summarises the information already shown on the diagram on the previous pages, to ensure the regu- lations in force are respected. Front passenger Front passenger seat without air Rear centre Rear seat with air bag Weight of...
Page 41 CHILD SAFETY: fitting a child seat (6/6) X = Seat not suitable for fitting child seats. U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted. IUF = Seat which, on equipped vehicles, allows forward-facing child seats with “Universal”...
Page 42: Deactivating/Activating The Front Passenger Air Bag
CHILD SAFETY: deactivating/activating the front passenger air bag (1/3) Deactivating the front To deactivate the passenger airbag, with the ignition off, press and turn passenger air bag button 1 to the OFF position. (depending on vehicle) With the ignition switched back on, it is To fit a rear-facing child seat on the essential to check that warning light 2, front passenger seat, you must deacti-...
Page 43 CHILD SAFETY: deactivating/activating the front passenger air bag (2/3) The markings on the dashboard and labels A on each side of the passenger sun visor 3 (as shown above) repeat these instructions. DANGER Since operation of the front passenger airbag is not compatible with the position of a rear-facing child seat, NEVER fit a restraint system for a rear-fac-...
Page 44 CHILD SAFETY: deactivating/activating the front passenger air bag (3/3) Activation of the front Operating faults passenger air bag It is forbidden to fit a rear-facing child (depending on vehicle) seat to the front passenger seat if the air bag activation/deactivation system You should reactivate the airbag as is faulty.
Page 45: Rear View Mirrors
REAR VIEW MIRRORS Door mirrors with electrical Door mirrors with manual Interior rear view mirror adjustment: adjustment The interior rear-view mirror is adjusta- ble. When driving at night, tilt lever 3 to With the ignition on, move button 1: To adjust the door mirror, move avoid being dazzled by the headlights –...
Page 46 DRIVER’S POSITION, LEFT-HAND DRIVE (1/2) 37 36 34 33 31 30 27 26 1.40...
Page 47 DRIVER’S POSITION, LEFT-HAND DRIVE (2/2) The fittings described DEPEND ON THE VEHICLE VERSION AND COUNTRY. 1 Side air vent. 12 Central demister outlet. 25 Cigarette lighter or accessories socket. 2 Side demister outlet. 13 Location for radio, navigation system or storage compartments. 26 Handbrake.
Page 48: Driving Position
DRIVING POSITION, RIGHT-HAND DRIVE (1/2) 9 10 21 20 1.42...
Page 49 DRIVING POSITION, RIGHT-HAND DRIVE (2/2) The presence of the equipment DEPENDS ON THE VEHICLE VERSION AND COUNTRY. 1 Side air vent. 11 Instrument panel. 23 Handbrake. 2 Side demister outlet. 12 Cruise control/speed limiter controls. 24 Door mirror adjustment control. 3 Location for passenger airbag or 13 –...
Page 50 WARNING LIGHTS (1/7) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. These warning lights require you Ò to stop immediately, for your own If the orange warning light safety, as soon as traffic conditions comes on while you are driving, allow.
Page 51 WARNING LIGHTS (2/7) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. Ò Warning light malfunction Ô Coolant temperature warn- (red or orange) ing light It goes out as soon as the engine starts. Urgent stop warning light (red) If this remains lit while driving and, de- This lights up when the ignition is pending on the vehicle, is accompanied...
Page 52 WARNING LIGHTS (3/7) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. É Preheating warning light (on Anti-lock braking warning diesel version) light This should come on when the igni- This lights up when the ignition is tion is switched on.
Page 53 WARNING LIGHTS (4/7) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. Warning light for the elec- Ð Speed limiter warning light tronic stability program Refer to the information on the (ESC) and traction control system “Speed limiter”...
Page 54 WARNING LIGHTS (5/7) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. á Main beam headlight tell-tale Engine oil change warning light light This lights up on the instrument panel Dipped beam headlight tell- when an oil change is required. tale Change the oil or have it changed as Front fog light tell-tale light...
Page 55 WARNING LIGHTS (6/7) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. Æ STOP light ù Indicator light ESC This lights up when the ignition “Electronic Stability is switched on and goes out as soon as Program ESC with understeer control the engine is started.
Page 56 WARNING LIGHTS (7/7) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. Warning lights on the ß Seat belt reminder light console B, C or D It comes on when the engine is started if the driver and/or passenger Front passenger air bag de- seat belt is not fastened (depending on activation warning light.
Page 57: Display And Indicators
DISPLAY AND INDICATORS (1/3) Rev counter 1 (rpm x 1,000) Speedometer 2 (kph or mph) Automatic gearbox display 3 This indicates the gear engaged. Refer to information on the “Automatic gear- Overspeed buzzer box” in Section 2. Depending on the vehicle, a buzzer sounds for approximately 10 seconds every 30 seconds, as long as the ve- hicle is travelling in excess of 72 mph...
Page 58 DISPLAY AND INDICATORS (2/3) Fuel gauge 4, 5 or 6 On-board computer A, B or C The number of squares lit shows the Refer to the information on the “Trip fuel level. When it is at minimum, the computer and warning system” in squares disappear and the low fuel Section 1.
Page 59: Trip Computer And Warning System
DISPLAY AND INDICATORS (3/3) Multifunction key 8 – Display selection By pressing the button you can shift from the total mileage recorder, trip mileometer and time or vice-versa. – Resetting the trip mileage re- corder Once the trip mileage display is se- lected, press and hold the button.
Page 60: On-Board Computer
ON-BOARD COMPUTER (1/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Resetting the trip mileage To reset the trip mileage recorder, the display must show the Trip mileometer function. Press and hold button 2 or 4. On-board computer 1 or 3 f) Estimated range g) Distance travelled...
Page 61: Interpreting Values Displayed After Resetting
ON-BOARD COMPUTER (2/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Interpreting some of the – You may also notice that the aver- age fuel consumption increases values displayed after when the vehicle is stationary and resetting the engine idling.
Page 62 ON-BOARD COMPUTER (3/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of display selections by repeatedly pressing 2 or 4 Interpreting the display selected Display A Display B Display C a) Total mileage recorder. b) Trip mileage recorder.
Page 63 ON-BOARD COMPUTER (4/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of display selections by repeatedly pressing 2 or 4 Interpreting the display selected Display A Display B Display C e) Current fuel consumption. –...
Page 64 ON-BOARD COMPUTER (5/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of display selections by repeatedly pressing 2 or 4 Interpreting the display selected Display A Display B Display C – j) Mileage before service Distance remaining until the next oil change.
Page 65 ON-BOARD COMPUTER (6/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of display selections by repeatedly pressing 2 or 4 Interpreting the display selected Display A Display B Display C j) Tyre pressure reset. –...
Page 66: Steering Wheel, Power-Assisted Steering
STEERING WHEEL, POWER-ASSISTED STEERING Power Assisted Steering With the engine running, do not leave the steering wheel at full lock while sta- tionary as this may damage the power- assisted steering pump. With the engine switched off, or if there is a system fault, it is still possible to turn the steering wheel.
Page 67: Clock
CLOCK Press and hold button 2 to enter the hour setting mode. When only the hours flash, press button 2 briefly, to scroll through them. Press and hold button 2 to enter the minute setting mode. When only the minutes flash, press button 2 briefly, to scroll through them.
Page 68: Audible And Visual Signals
AUDIBLE AND VISUAL SIGNALS (1/2) Horn Direction indicators Press the end of the stalk 1. Move stalk 1 parallel to the steering wheel and in the direction you are going Depending on the vehicle, press on one to turn it. of areas 2.
Page 69 AUDIBLE AND VISUAL SIGNALS (2/2) Hazard warning lights é Press switch 3. This switch activates all four direction indicators and the side indicator lights simultaneously. It must only be used in an emergency to warn drivers of other vehicles that you have had to stop in an area where stop- ping is prohibited or unexpected, or that you are obliged to drive under special...
Page 70: Exterior Lighting And Signals
EXTERIOR LIGHTING AND SIGNALS (1/2) Side lights á Main beam headlights Switching off the lights With the dipped beam head- From the main beam head- lights lit, push stalk 1. This indicator lights position, pull the stalk 1 towards light on the instrument panel comes on. you, then turn the end of the stalk 1 š...
Page 71 EXTERIOR LIGHTING AND SIGNALS (2/2) Rear fog lights Turn the centre ring 3 on the stalk until the symbol faces mark 2. The fog lights only light up if the exterior lights have been switched on. An indi- cator light on the instrument panel then lights up.
Page 72: Adjusting The Headlight Beam Height
ADJUSTING THE HEADLIGHT BEAM HEIGHT (1/2) Examples of positions for adjusting control A according to the load Control A Control A 3 positions 4 positions Driver alone or with front passenger Driver with one front passenger and The control A is used to adjust the one rear passenger height of the headlight beams accord- ing to the load.
Page 73 ADJUSTING THE HEADLIGHT BEAM HEIGHT (2/2) Temporary adjustment Open the bonnet and identify the mark- ing B next to one of the front headlight projectors. For each headlight, using a screw- driver, turn the screw 1 by a quarter turn towards the - symbol to lower the beams.
Page 74 WINDSCREEN WASH, WIPE (1/2) Windscreen wiper With the ignition on, pull stalk 1 towards you. A brief pull will trigger a single sweep In frosty weather, make sure that of the wipers, in addition to the wind- the wiper blades are not stuck by ice screen washer.
Page 75: Screen Washer/Wiper
WINDSCREEN WASH, WIPE (2/2) Rear screen washer/ wiper With the ignition on, turn the end of stalk 1 to align the symbol with mark 2. When the stalk is released, it returns to the rear wipe position. Rear screen wiper With the ignition on, turn the end of stalk 1 to align the symbol with mark 2.
Page 76 FUEL TANK (1/6) Petrol and diesel versions There is a cap holder 3 on the fuel filler flap for holding the cap when the tank is Usable capacity of the fuel tank: being filled. 50 litres approximately. Fuel filler cap: this is spe- Depending on the vehicle, lift lever 2 to Depending on the vehicle, to open the cific to the vehicle type.
Page 77: Fuel Grade
FUEL TANK (2/6) Fuel grade Vehicles running on ethanol-based fuel Always use a high-grade fuel that Always use unleaded petrol or fuel complies with the legislation in force containing a maximum of 85 percent in each country. It must conform to the ethanol (E85).
Page 78: Fuel Tank Filling With Fuel
FUEL TANK (3/6) Filling with fuel Petrol versions Using leaded petrol will damage the Insert the nozzle to open the valve and antipollution system and may lead to a insert it fully before turning it on to fill loss of warranty. the fuel tank (risk of splashing).
Page 79 FUEL TANK (4/6) LPG versions Useful capacity of fuel tank: approx. 34 litres. Filling up with LPG Engage the handbrake, stop the engine, switch off the ignition and switch off the lights. Always respect the safety instructions given at filling stations. It is always advisable to completely fill the tank.
Page 80 FUEL TANK (5/6) When the pump finishes or if it has dif- ficulties operating, this means that the maximum tank fill level (80%) has been reached. The filling will stop as soon as you re- lease the button. Release the stop lever (a small amount of gas may be re- leased), lift the pistol and place it on the distributor.
Page 81 FUEL TANK (6/6) No modifications what- soever are permitted on any part of the fuel supply system (computers, wiring, fuel circuit, injector, protection covers, etc.) as this may be danger- ous (such work must be undertaken by qualified Network personnel). Priming bulb (diesel version) After a breakdown caused by com-...
Page 82 1.76...
Page 83 Section 2: Driving (Advice on use relating to fuel economy and the environment) Running in, Ignition switch ............Starting/stopping the engine .
Page 84: Running In, Ignition Switch
RUNNING IN, IGNITION SWITCH Petrol version Ignition on position M For the first 600 miles (1,000 km), do The ignition is switched on: not exceed 78 mph (130 km/h) in the – petrol version: the engine may be highest gear, or 3,000 to 3,500 rpm. started.
Page 85: Starting/Stopping The Engine
STARTING, STOPPING THE ENGINE (1/4) Starting the engine LPG versions At temperatures close to 0°C or less, it is recommended to use ECO mode to In very cold conditions (temperatures The engine is always started using maximise the use of LPG. Please refer below –20°C): so that it is easier to petrol: to the information on “Driving advice,...
Page 86: Stopping The Engine
STARTING, STOPPING THE ENGINE (2/4) vehicles with an automatic Stopping the engine gearbox With the engine idling, turn the key Driver’s responsibility back to “Stop” position St. Before starting, move the lever to posi- Never leave an animal, tion P. child or adult who is not Special note Refer to the information on the...
Page 87 STARTING, STOPPING THE ENGINE (3/4) The remote engine start-up operates if: – the lever is in neutral for vehicles with a manual or sequential gearbox; – the lever is in position P for vehicles with an automatic gearbox; – the ignition is off and no key is in- serted into the ignition switch;...
Page 88 STARTING, STOPPING THE ENGINE (4/4) Do not use the engine remote start-up function or its programming when: – the vehicle is in a garage or in a confined space. Risk of poisoning or suffocation by exhaust gas emissions. – the vehicle is covered with a protective cover. Fire hazard.
Page 89: Stop And Start Function
STOP AND START function (1/3) This system enables a reduced fuel For manual gearboxes: consumption and lower greenhouse – the gearbox is in neutral; If you get out of the vehicle, a beep gas emissions. notifies you that the engine is on The system is activated automatically standby and has not been switched when the vehicle is started.
Page 90 STOP AND START function (2/3) Preventing the engine from Conditions for coming out of Conditions preventing the standing by engine standby standby of the engine In certain situations, when negotiating For automatic or sequential gear- Certain conditions prevent the system a junction for instance, it is possible to box: from using the engine standby function,...
Page 91 STOP AND START function (3/3) Special feature of the automatic The system is automatically reacti- engine re-start vated each time the vehicle is started (see “Starting, stopping the engine” in Under certain conditions, the engine Section 2). can restart on its own in order to guar- antee your safety and comfort.
Page 92: Special Features Of Petrol Versions
SPECIAL FEATURES OF PETROL VERSIONS The following operating conditions: If you notice any of the above operating faults, have the necessary repairs car- – driving for long periods when the low ried out as soon as possible by an ap- fuel level warning light is lit;...
Page 93: Special Features Of Diesel Versions
SPECIAL FEATURES OF DIESEL VERSIONS Diesel engine speed Precautions to be taken in winter Diesel engines are fitted with an injec- tion pump which prevents the engine To avoid any faults in icy weather: speed being exceeded irrespective of – ensure that the battery is always fully the gear selected.
Page 94: Special Features Of Lpg Versions
SPECIAL FEATURES OF LPG VERSIONS (1/3) LPG vehicles Fuel gauge warning light A These vehicles operate using petrol or The warning lights A (4 green lights and LPG. 1 red light) indicate the level in the LPG They have two separate tanks. tank.
Page 95 SPECIAL FEATURES OF LPG VERSIONS (2/3) Pressing control C stops the beep from sounding and only the yellow warning light B stays on. Depending on the vehicle, under cer- tain conditions of use, the system may opt to temporarily switch back to petrol mode without any beep sounding (ex- ample: strong acceleration).
Page 96: In The Event Of An Accident
SPECIAL FEATURES OF LPG VERSIONS (3/3) If driving under severe LPG has a very specific conditions smell so you will be able to detect any leaks easily. If If driving under severe conditions you smell gas in your vehi- (heavily laden vehicle, high outside cle or immediately surrounding your temperature, starting on a steep slope, vehicle:...
Page 97: Driving Advice, Eco-Driving
DRIVING ADVICE, ECO-DRIVING (1/5) Fuel consumption is accredited in ac- cordance with a standard regulatory method. Identical for all manufactur- ers, this enables vehicles to be com- pared with one another. Consumption in real time depends on vehicle usage conditions, the equipment fitted and the user’s driving style.
Page 98: Eco Mode
DRIVING ADVICE, ECO-DRIVING (2/5) ECO mode While driving, it is possible to leave the ECO mode temporarily in order to im- ECO mode is a function which opti- prove engine performance. mises fuel consumption. This acts on To do this, press the accelerator pedal certain consumption components, such firmly and fully.
Page 99 DRIVING ADVICE, ECO-DRIVING (3/5) – Avoid sudden acceleration. – Brake as little as possible. If you an- ticipate an obstacle or bend in ad- vance, you may then simply release the accelerator pedal. – Do not try to maintain the same speed up a hill, accelerate no more than you would on the level.
Page 100 DRIVING ADVICE, ECO-DRIVING (4/5) Tyres Your vehicle has a greater – An underinflated tyre increases fuel ground clearance than an consumption. ordinary passenger vehicle. – The use of non-recommended tyres This gives it a higher centre can increase fuel consumption. of gravity, making it more suscep- tible to rolling during sudden or ag- gressive manoeuvres, or when cor-...
Page 101 DRIVING ADVICE, ECO-DRIVING (5/5) – In vehicles fitted with air condi- tioning, it is normal to observe an increase in fuel consumption (es- pecially in urban conditions) when it is used. For vehicles fitted with manual air conditioning, switch off the system when it is not required.
Page 102: Engine Adjustments
MAINTENANCE AND ANTIPOLLUTION ADVICE Your vehicle complies with criteria for Maintenance Exhaust gas monitoring recycling and recovering vehicles at the system It is important to remember that fail- end of their service life, which will come ure to respect anti-pollution regulations The exhaust gas monitoring system will into force in 2015.
Page 103: Environment
ENVIRONMENT Your vehicle has been designed with Emissions – At the end of the vehicle’s service respect for the environment in mind for life, it should be sent to approved Your vehicle has been designed to emit its entire service life: during production, centres to ensure that it is recycled.
Page 104: Tyre Pressure Loss Warning
TYRE PRESSURE LOSS WARNING (1/7) When fitted to the vehicle, this system System identification notifies the driver if one or more tyres There are two tyre pressure loss warn- lose pressure. ing systems: – System A: can be seen on the label A in the vehicle.
Page 105 TYRE PRESSURE LOSS WARNING (2/7) Operating conditions – fitting a single new tyre; – use of tyres not approved by the net- The system has to be reset with an in- work. flation pressure equal to that written – ... on the tyre inflation pressure label.
Page 106 TYRE PRESSURE LOSS WARNING (3/7) SYSTEM A (cntd.) Display Inflate tyres and SEt tP Resetting the standard level for the tyre pressures The warning light comes on (not This should be done: flashing). – after each reinflation or readjustment This indicates that at least one tyre is of the pressure of one of the tyres;...
Page 107 TYRE PRESSURE LOSS WARNING (4/7) SYSTEM A (cntd.) Readjustment of tyre pressures After each change of wheel/tyre, rea- djust the tyre pressure and launch the The tyre pressures must be adjusted Relaunch SEt tP reset of the tyre pressure reference when cold (please refer to the label lo- value.
Page 108 TYRE PRESSURE LOSS WARNING (5/7) Resetting the standard level for the tyre pressures This should be performed: – when the standard tyre pressure needs to be changed to adapt to usage conditions (empty, carrying a load, motorway driving, etc.); – after changing wheels around; –...
Page 109 TYRE PRESSURE LOSS WARNING (6/7) Note: Puncture The standard tyre pressure cannot be The warning light and the red less than that recommended and indi- Ò cated on the door frame. warning light come on steady, together with a beep. Display They indicate that at least one wheel Check tyre pressure...
Page 110 TYRE PRESSURE LOSS WARNING (7/7) SYSTEM B (cntd.) Replacing wheels/tyres Inflation kit This system requires specific equip- Because the valves are specially de- Check tyre sensors ment (wheels, tyres, hubcaps, etc.). signed, only use equipment approved Please see the information on “Tyres” by the approved network.
Page 111: Gear Lever, Handbrake
GEAR LEVER, HANDBRAKE Handbrake To release Pull lever 2 up slightly, press button 3 and then lower the lever to the floor. The red warning light on the instrument panel will come on if you are driving with an incorrectly released handbrake. To apply Pull lever 2 upwards and make sure the vehicle is immobilised.
Page 112: Transmission: 4-Wheel Drive (4Wd)
TRANSMISSION: 4-wheel drive (4WD) (1/4) “AUTO" mode To activate this mode, turn the selec- tor 1 to the “AUTO” position. Operating principle “AUTO” mode automatically distributes the engine torque between the front and rear axles according to the road condi- tions and the vehicle speed.
Page 113 TRANSMISSION: 4-wheel drive (4WD) (2/4) To deactivate this mode, turn selector 1 After one minute, the system switches This problem may be resolved by chan- ‘ to “2WD” or “AUTO” mode depending ging the tyres. Always use four identi- to the “AUTO” position. The indi- on the position of the selector.
Page 114 TRANSMISSION: 4-wheel drive (4WD) (3/4) In this case, we recommend that you Electronic stability program and Operating faults stop as soon as possible to allow the traction control when driving off- If the system detects an operating system to cool down (until the warning road fault, it automatically switches to “2WD”...
Page 115 TRANSMISSION: 4-wheel drive (4WD) (4/4) All-wheel drive system – Irrespective of the mode selected, do not start the engine if one or more wheels are not in contact with the ground (eg. when the vehicle is on a jack or roller bench). –...
Page 116: Driver Correction Devices/Aids
DRIVER CORRECTION DEVICES/AIDS (1/4) Depending on the vehicle, this is com- ABS (anti-lock braking Special feature of 4-wheel drive vehi- posed of: cles system) – the (anti-lock braking In 4WD Lock mode, the system may Under heavy braking, the ABS prevents system);...
Page 117 DRIVER CORRECTION DEVICES/AIDS (2/4) Operating faults Emergency brake assist with electronic brake distribution – If the warning light on the ins- (depending on the vehicle) trument panel comes on while you This system supplements the ABS are driving, the brakes will still and helps reduce vehicle stopping dis- work normally without ABS;...
Page 118 DRIVER CORRECTION DEVICES/AIDS (3/4) Deactivating the ESC function In some situations (driving on very wet ground: snow, mud, etc. or driving with snow chains fitted), the system may reduce the engine output to limit whee- lspin. If this is not required, it is possible to deactivate the function by pressing switch 1.
Page 119 DRIVER CORRECTION DEVICES/AIDS (4/4) Operating principle Hill start assistance A sensor in the steering wheel detects This function assists the driver when the direction selected by the driver. starting on hills. It prevents the vehicle from rolling forwards or backwards by The hill start assistance Other sensors throughout the vehicle automatically applying the brakes when...
Page 120 CRUISE CONTROL/SPEED LIMITER: speed limiter function (1/3) The speed limiter function helps you Controls Switching on stay within the driving speed limit that 1 Main “On/Off” switch. Press switch 1 on the side showing you choose, known as the limit speed. The warning light 6 is orange and, de- 2 Limit speed activation, storage and pending on the vehicle, the message...
Page 121: Speed Limiter
CRUISE CONTROL/SPEED LIMITER: speed limiter function (2/3) Varying the limit speed Exceeding the limit speed The limit speed may be changed by re- It is possible to exceed the limit speed peatedly pressing: at any time. To do this: press the accel- erator pedal firmly and fully (beyond –...
Page 122 CRUISE CONTROL/SPEED LIMITER: speed limiter function (3/3) Recalling the limit speed If a speed has been saved, it can be re- called by pressing switch 4 ((R)). Putting the function on Switching off the function standby The speed limiter function is deac- tivated if you press switch 1: in this The speed limiter function is suspended case a speed is no longer stored.
Page 123 CRUISE CONTROL/SPEED LIMITER: cruise control function (1/4) This function is an addi- tional driving aid. However, the function does not take the place of the driver. Therefore, it can under no circum- The cruise control function helps you to Controls stances replace the driver’s respon- maintain your driving speed at a speed sibility to respect speed limits and to...
Page 124: Cruise Control
CRUISE CONTROL/SPEED LIMITER: cruise control function (2/4) Switching on Activating cruise control Driving At a steady speed (above 18 mph Once a cruising speed is stored and Press switch 1 side (30 km/h approximately)) press switch 2 the cruise control function is active, The green warning light 6 comes on or (+): the function is activated and the you may lift your foot off the accelera-...
Page 125 CRUISE CONTROL/SPEED LIMITER: cruise control function (3/4) Exceeding the cruising speed The cruising speed may be exceeded at any time by depressing the accelera- tor pedal. While it is being exceeded, the cruising speed flashes on the in- strument panel. Then, release the accelerator: after a few seconds, the vehicle will automati- cally return to its set cruising speed.
Page 126 CRUISE CONTROL/SPEED LIMITER: cruise control function (4/4) Returning to the cruising speed If a speed is stored, it can be recalled, once you are sure that the road con- ditions are suitable (traffic, road sur- face, weather conditions, etc.). Press switch 4 (R) if the vehicle speed is above 20 mph (30 km/h).
Page 127: Automatic Gearbox
AUTOMATIC GEARBOX (1/4) Driving in automatic mode Place the lever into position D. In the majority of driving conditions, you will no longer have to use your gear lever: the gears change automatically, at the right time, to a suitable engine speed because “automatic”...
Page 128 AUTOMATIC GEARBOX (2/4) Special cases In certain driving conditions (e.g.: to protect the engine) the “automated system” may change the gear automat- ically. Likewise, to prevent incorrect manoeu- vres, a gear change may be refused by the automatic system: in this case the gear display flashes for a few seconds as a warning.
Page 129 AUTOMATIC GEARBOX (3/4) – Vehicles not fitted with traction control: on a slippery surface or surface with a low level of adhesion, change to manual mode and select second gear (or even third) before starting the engine to avoid wheel- spin when accelerating.
Page 130: Parking The Vehicle
AUTOMATIC GEARBOX (4/4) Parking the vehicle When the vehicle is stopped, move the lever to position P while keeping your foot on the brake pedal: the gearbox is in neutral and the drive wheels are me- chanically locked by the driveshaft. Apply the handbrake.
Page 131: Parking Distance Control
PARKING DISTANCE CONTROL (1/2) Operating principle Ultrasonic sensors, fitted in the vehi- cle’s rear bumper, measure the dis- tance between the vehicle and an ob- stacle when reversing. This measurement is indicated by beeps which become more frequent the closer you come to the obstacle, until they become a continuous beep when This function is an addi- the vehicle is approximately 40 centi-...
Page 132 PARKING DISTANCE CONTROL (2/2) Operating faults When the system detects an operat- ing fault, there will be a three-second continuous beep as a warning. Please consult an authorised dealer. Deactivating the system You can deactivate the system by pressing switch 1. The warning light built into the switch remains lit constantly.
Page 133: Reversing Camera
REVERSING CAMERA (1/2) Operation Note: make sure that the reversing camera is not obscured (by dirt, mud, When using reverse gear, the camera 1 snow, etc.). located near the tailgate sends a view of the area behind the vehicle to the multimedia display 2 together with a static guide line.
Page 134 REVERSING CAMERA (2/2) This gauge remains fixed and indicates the vehicle trajectory if the wheels are in line with the vehicle. Static guide line 3: The static guide line 3 has coloured markers A, B and C showing the dis- The screen shows a reverse image.
Page 135: Your Comfort
Section 3: Your comfort Air vents, air outlets ............. . Air conditioning: information and advice on use .
Page 136: Air Vents, Air Outlets
AIR VENTS, air outlets (1/2) 1 Left-hand side air vent 6 Right-hand side window demister vent 2 Left-hand side window demister vent 7 Right-hand side air vent 3 Windscreen demisting vents 8 Front passenger footwell heater outlets 4 Centre air vents 9 Rear passenger footwell heater 5 Control panel outlets (depending on the vehicle)
Page 137 AIR VENTS, air outlets (2/2) Centre and side air vents Rear seats To remove bad odours from your ve- hicles, only use the systems designed (depending on vehicle) Air flow for this purpose. Consult an approved Passenger footwell heater outlets 12. Dealer.
Page 138 HEATING, VENTILATION, AIR CONDITIONING (1/3) Adjusting the air temperature Turn control 5 to obtain the desired temperature. The further towards the red the slide is, the higher the tempera- ture will be. Adjusting the ventilation fan speed. Turn control 3 from 0 to 4. The further to the right it is positioned, the more air is blown into the passenger compart- ment.
Page 139 HEATING, VENTILATION, AIR CONDITIONING (2/3) Rapid demisting Turn controls 1, 3 and 6 to positions – air from the outside; – maximum fan speed; – demisting. Using the climate control increases the speed of demisting. Heated rear windscreen/ Heated windscreen Switching passenger Air recirculation is used to: With the engine running, press...
Page 140 HEATING, VENTILATION, AIR CONDITIONING (3/3) Switching air conditioning on or off The air conditioning is switched on (in- dicator light illuminated) or off (indicator light extinguished) using button 2. Activation is not possible if control 3 is set to 0. The air conditioning system is used for: –...
Page 141: Air Conditioning: Information And Advice On Use
AIR CONDITIONING: information and advice on use Fuel consumption Operating faults You will normally notice an increase As a general rule, contact your ap- in fuel consumption (especially proved dealer in the event of an op- when driving in town) when the air erating fault.
Page 142 ADDITIONAL AIR CONDITIONING When fitted, the vehicle has four adjust- Heating and air conditioning able air vents 1 and an air-conditioning system control 2. Move control 2 to vary the amount of cold air required. The amount of air can only be adjusted if the basic air conditioning is operating (button 3).
Page 143: Electric Windows
ELECTRIC WINDOWS (1/3) Manual window winders Electric windows From the front passenger seat Turn the handle 1 to lower or raise the With the ignition on, press the switch window to the desired height. to lower the window to the required Operate switch 6.
Page 144 ELECTRIC WINDOWS (2/3) From the rear seats Operate switch 7. Safety of rear occupants The driver can prevent operation of the rear electric windows by press- ing switch 8. Driver’s responsibility Never leave your vehicle with the key or remote control inside and never leave a child (or a pet) unsupervised, even for a short while.
Page 145 ELECTRIC WINDOWS (3/3) One-touch windows Operating faults When the vehicle is equipped with this In case of a fault when closing a window, function, the one-touch mode works in the system reverts to normal mode: pull addition to the operation of the electric the switch concerned up to fully close windows described previously.
Page 146: Interior Lighting
INTERIOR LIGHTING (1/2) Courtesy light Map reading lights Pressing switch 1 provides: Pressing switch 2 provides: – continuous lighting; – continuous lighting; – or temporary lighting by opening one – no lighting. of the front doors, or by opening one of the four doors, depending on the vehicle.
Page 147 INTERIOR LIGHTING (2/2) Glovebox light 3 Boot light 4 Light 3 comes on when the cover is The light 4 comes on when the boot is opened. opened. Automatic operation of interior li- ghting (depending on the vehicle) – if the doors are unlocked using the remote control, the lighting is switched on for approximately 30 seconds.
Page 148: Sun Visor/Grab Handle
SUN VISOR/GRAB HANDLE Sun visor Grab handle 4 Lower the sun visor 1 or 3 over the This offers support and can be held windscreen or unclip it and turn it over when the vehicle is being driven. the side window. Do not use these for getting into or out of the vehicle.
Page 149 ASHTRAYS/CIGAR LIGHTER/ACCESSORIES SOCKET Ashtray Cigarette lighter 3 It can be housed in either position 1 With the ignition on, push in the ciga- or 4. rette lighter 3. Lift the cover 2 to open. It will spring back with a click when it is ready.
Page 150: Rear Headrests
REAR HEADRESTS To remove the headrests A or B Position for using the headrest B (depending on vehicle) Raise the headrest as far as it will go, then press button 1 and remove the Lift the headrest to maximum height, headrest.
Page 151: Passenger Compartment Storage Space And Fittings
PASSENGER COMPARTMENT STORAGE SPACE AND FITTINGS (1/4) Front door storage Dashboard upper storage Mobile phone storage compartments 1 compartment 2 compartment 3 (depending on the vehicle) Ensure that no hard, heavy or pointed objects are Nothing should be placed placed in the “open” sto- on the floor area in front of Do not hang any heavy and/ rage compartments in such...
Page 152 PASSENGER COMPARTMENT STORAGE SPACE AND FITTINGS (2/4) Centre console storage Centre console storage compartment 4 compartment 5 (or radio location) (or location of the 4x2 (2WD) and 4X4 (4WD) mode selector) Locations for cup holder or ashtray 6. Ensure that no hard, heavy or pointed objects are When cornering, accelera- placed in the “open”...
Page 153 PASSENGER COMPARTMENT STORAGE SPACE AND FITTINGS (3/4) Passenger side glove box This glove box can be used to store A4 format documents. Pull handle 7 to open it. Inside the cover, a section 8 has been provided for pens, maps, etc. Precautions during use Cover A in the bottom of the glove box protects a socket reserved ex-...
Page 154 PASSENGER COMPARTMENT STORAGE SPACE AND FITTINGS (4/4) Front seat storage pockets 9 Bottle holders 10 Rear armrest storage 11 It can hold a 1.5 litre bottle. Depending on the vehicle, a storage compartment may be fitted in the rear armrest. Pull down the armrest 11.
Page 155: Rear Bench Seat
REAR BENCH SEAT (1/3) Depending on the vehicle, the seat A Lower the rear headrests completely and the seatback B or C may be folded (refer to the information on the “Rear away to allow bulky objects to be car- headrests”...
Page 156 REAR BENCH SEAT (2/3) To reposition the seat back B or C Lift the seatback(s). Check the seatbacks are correctly locked in position. Refit the rear headrests (refer to the information on the “Rear headrests” in Section 3). To fold away the seat base Tilt the seat base A against the front seats.
Page 157 REAR BENCH SEAT (3/3) To reposition the seat A in place Unbuckle all of the rear seat belts and position them correctly (refer to the in- Fasten all of the rear seat belts before formation on the “Rear seat belts” in refitting the seat base (refer to the in- Section 1).
Page 158: Manual Control
TAILGATE Manual control Electric central locking To open, insert the key in the lock and The tailgate is locked and unlocked at turn it (movement A). the same time as the doors. Remove the key and press button 1. To open, press the button 1 and lift the Lift the tailgate.
Page 159 TRANSPORTING OBJECTS IN THE BOOT (1/2) Always position the objects trans- ported so that the largest surface is against: – the rear bench seatbacks, for normal loads (eg: A); – the front seats when the rear seats are folded down. Refer to the infor- mation on the “Rear bench seat: functions”...
Page 160 TRANSPORTING OBJECTS IN THE BOOT (2/2) Always position the heavi- est items directly on the floor. Use the lashing points 1 on the boot floor, if these are fitted to the vehicle. The luggage should be loaded in such a way that no items will be thrown for- ward and strike the occupants if the driver has to brake suddenly.
Page 161 TRANSPORTING OBJECTS towing, attachments If the towbar ball obscures the re- gistration plate or the rear lights, it should be removed when not in use. In all cases, comply with local legis- lation. Depending on the vehicle, LPG versions A= 901 mm or 950 mm Permissible nose weight, maxi- Certain LPG versions are mum permissible towing weight...
Page 162: Rear Parcel Shelf
REAR PARCEL SHELF The parcel shelf 2 is made up of two Lift the parcel shelf 2 to half height and Gently lift the parcel shelf 2 and pull it rigid sections. unclip the mountings 3 located on each towards you, holding it at each end. side of the parcel shelf.
Page 163: Roof Bars
LONGITUDINAL ROOF BARS If fitted to the vehicle, you can use the mounting holes 2 of the longitudinal bars to: – use luggage restraint systems (straps, cords, etc.); – attach additional items without using the transverse roof bars. If fitted on the vehicle, you can trans- port luggage or additional equipment (bike racks, ski racks, etc): For information on the range of...
Page 164: Multimedia Equipment
MULTIMEDIA EQUIPMENT The presence and location of this Hands-free telephone equipment depends on the vehicle’s integrated control multimedia equipment. On equipped vehicles, use micro- 1 Radio or navigation system phone 3 and steering column control 2. 2 Steering column control; 3 Microphone.
Page 165 Section 4: Maintenance Bonnet ............... . Engine oil level: general information .
Page 166: Bonnet
BONNET (1/2) Deactivate the Stop and Start function for any opera- tion performed in the engine compartment. To open the bonnet, pull handle 1. Opening the bonnet Lift the bonnet and guide it upwards; it Unlocking the bonnet catch is held by strut 3. When working in the engine To unlock, raise the bonnet slightly and compartment, ensure that...
Page 167 BONNET (2/2) Never activate the remote engine start-up function or its programming before opening the bonnet or when it is open. Risk of burns or serious injury. Ensure that the bonnet is prop- erly locked. Check that nothing is preventing the catch from locking (gravel, cloth, etc.).
Page 168: Engine Oil Level: General Information
ENGINE OIL LEVEL: general information It is normal for an engine to use oil for – remove the dipstick and wipe with a lubrication and cooling of moving parts clean, lint-free cloth; and it is normal to top up the level be- –...
Page 169: Engine Oil Level: Topping Up/Filling
ENGINE OIL LEVEL: topping up, filling (1/3) Topping up/filling – Unscrew cap 1; – top up the level (as a guide, the ca- The vehicle must be parked on level pacity between the minimum and ground and the engine should be cold maximum reading on dipstick 2 is (for instance, before the engine is between 1.5 and 2 litres, depending...
Page 170 ENGINE OIL LEVEL: topping up, filling (2/3) If there is an abnormal or repeated Filling: take care when drop in the fluid level, please consult topping up the oil that an authorised dealer. no oil drips onto engine components - risk of fire. Remember to refit the cap securely as there is a risk of fire if oil splashes Engine oil change: if you...
Page 171: Oil Change
ENGINE OIL LEVEL: topping up, filling (3/3) Oil change Resetting the alert after an oil change Service interval: refer (depending on the vehicle) Maintenance Document for your vehi- cle. If you change the oil yourself, you will need to reset the oil change warning. To do this, after switching on the igni- Oil change capacity tion, for ten seconds you must:...
Page 172: Levels
LEVELS (1/3) Level Topping up It is normal for the level to drop as the After any operation on the hydraulic cir- brake shoes become worn, but it must cuit, a specialist must replace the fluid. never drop lower than the “MINI” warn- Only use fluids approved by our ing line shown on brake fluid reser- Technical Department (and taken from...
Page 173: Windscreen Washer Reservoir
LEVELS (2/3) Coolant level checking frequency Check the coolant level regularly (very severe damage is likely to be caused to the engine if it runs out of coolant). If the level needs to be topped up, only use products approved by our Technical Department which ensure: –...
Page 174 LEVELS (3/3) Power-assisted steering fluid reservoir 4 or 5 Level: for a correct level when cold, with the engine switched off and on level ground, it must be visible between If you feel any variation in the ef- the “MINI” and “MAXI” marks on reser- fectiveness of the power-assisted voir 4 or 5.
Page 175: Filters
FILTERS The replacement of filter elements (air If clogging level indicator 2 reaches filter, passenger compartment filter, 100%, consult an approved dealer as diesel filter, etc.) is scheduled in the soon as possible to have the filter re- maintenance operations for your vehi- placed.
Page 176: Tyre Pressure
TYRE PRESSURE (1/2) For your safety, please re- spect the speed limit. When they need to be re- placed, only tyres of the same make, size, type and profile should be used on a single axle. They must: either have a load ca- pacity and speed rating at least equal to those of the original Label A...
Page 177 TYRE PRESSURES (2/2) Special note concerning fully laden Vehicle fitted with a tyre pressure vehicles (Maximum Permissible All-Up loss warning system Weight) and towing a trailer: the maxi- If under-inflated (puncture, low pres- mum speed must be limited to 60 mph (100 kph) and the tyre pressure in- sure, etc.), the warning light on...
Page 178: Battery
BATTERY (1/2) The charge status of your battery can decrease especially if you use your vehicle: – for short journeys; – for driving in town; – when the temperature drops; – after extended use of consumers (radio etc.) with the engine switched off.
Page 179 BATTERY (2/2) Label A Observe the indications on the battery: – 2 Naked flames and smoking forbid- den; – 3 Wear eye protection; – 4 Keep away from children; – 5 Explosive substances; – 6 Refer to the handbook; – 7 Corrosive substances. The engine may be hot during operations in close proximity.
Page 180: Bodywork Maintenance
BODYWORK MAINTENANCE (1/2) A well-maintained vehicle will last What you should not do You should longer. It is therefore recommended to Do not degrease or clean mechani- Wash your car frequently, with the maintain the exterior of the vehicle reg- cal components (e.g.
Page 181 BODYWORK MAINTENANCE (2/2) Respect local regulations about wash- Vehicles with a matte paint Using a roller type car wash ing vehicles (e.g. do not wash your ve- finish Return the windscreen wiper stalk to hicle on a public highway). the Park position (refer to the informa- This type of paint requires certain pre- Observe the vehicle stopping distances tion on the “Windscreen washer, wiper”...
Page 182: Interior Trim Maintenance
INTERIOR TRIM MAINTENANCE (1/2) A well-maintained vehicle will last Glass instrument panel Textiles (seats, door trim, etc) longer. It is therefore recommended to (e.g. instrument panel, clock, exterior Vacuum-clean the textiles regularly. maintain the interior of the vehicle regu- temperature display, radio display, etc.) larly.
Page 183: The Vehicle
INTERIOR TRIM MAINTENANCE (2/2) Removal/replacing removable You should not: equipment originally fitted in You are strongly advised not to po- the vehicle sition objects such as deodorants, scents, etc. near air vents, as this could If you need to remove equipment in damage your dashboard trim.
Page 184 4.20...
Page 185 Section 5: Practical advice Tools ............... . . Puncture .
Page 186: Tools
TOOLS Accessing the tools Jack 4 Wheelbrace 5 To use the jack, undo nut 2. When refit- This is used to tighten/loosen the wheel The tools are located in the luggage ting, fold the jack before placing it in its bolts and, depending on the vehicle, to compartment.
Page 187: Puncture
PUNCTURE (1/2) In the event of a puncture, To store the wheel in the cage: depending on the vehicle, – Place the punctured tyre in the sub- you will have: frame 4; – reattach the cage 4 and retighten the An emergency spare wheel or tyre in- screw using wheelbrace 1 to refit the flation kit (refer to the information on the...
Page 188 PUNCTURE (2/2) Vehicle fitted with a tyre pressure loss warning system If under-inflated (puncture, low pres- sure, etc.), the warning light lights up on the instrument panel. See “Tyre pressure loss warning” in Section 2. Emergency spare wheel 4x4 If the emergency spare wheel has been stored for several years, have it version (4WD) checked by your Dealer to ensure that it is safe to use.
Page 189: Tyre Inflation Kit
TYRE INFLATION KIT (1/4) Do not attempt to use the The kit is only approved inflation kit if the tyre has for inflating the tyres of the been damaged as a result vehicle initially fitted with the of driving with a puncture. kit.
Page 190 TYRE INFLATION KIT (2/4) Vehicle fitted with a tyre pressure loss warning system If under-inflated (puncture, low pres- sure, etc.), the warning light lights up on the instrument panel. See “Tyre pressure loss warning” in Section 2. In the event of a puncture, use the kit C On 4x2 versions, unclip flap D.
Page 191 TYRE INFLATION KIT (3/4) For all vehicles, with the engine run- Note: while the container is empty- Nothing should be placed ning and the handbrake applied, ing (approximately 30 seconds), the around the driver’s feet pressure gauge 5 will briefly indicate –...
Page 192 TYRE INFLATION KIT (4/4) – Start immediately and drive at be- tween 12 and 40 mph (20 and 60 km/h) in order to distribute the product evenly in the tyre and, after driving for 2 miles (3 km), stop and check the pressure.
Page 193: Wheel Trim/Wheels
WHEEL TRIM/WHEELS Central wheel trim with Central wheel trim with visible wheel bolts visible wheel bolts (example: wheel trim 1) (example: wheel trim 2) The bolts are directly accessible. Remove it using the hubcap tool, by in- serting the hook near a wheel bolt. To put it back, position hooks 4 in rela- tion to bolts 3.
Page 194: Changing A Wheel
CHANGING A WHEEL (1/2) Mark hole 1, which is the nearest to Switch on the hazard war- the wheel in question. The jack must ning lights. be fitted in this location. Offer up jack 3 horizontally and position jack head 2 Park the vehicle away from under the sill.
Page 195 CHANGING A WHEEL (2/2) Vehicle fitted with a tyre pressure loss warning system If under-inflated (puncture, low pres- If the vehicle is not equipped with a jack or wheelbrace, you can obtain sure, etc.), the warning light these from your approved dealer. lights up on the instrument panel.
Page 196: Tyres
TYRES (1/4) Tyre and wheel safety When the tyre tread has been worn to the level of the warning strips, they The tyres are the only contact between become visible 2: it is then necessary the vehicle and the road, so it is essen- to replace your tyres because the tread tial to keep them in good condition.
Page 197: Tyre Pressures
TYRES (2/4) Tyre pressures Pressures should be checked when the Vehicle fitted with a tyre pressure tyres are cold; ignore higher pressures loss warning system Adhere to the tyre pressures (including which may be reached in hot weather If under-inflated (puncture, low pres- the emergency spare wheel).
Page 198: Emergency Spare Wheel
TYRES (3/4) Fitting new tyres For safety reasons, this operation must be carried out by a specialist. Fitting different tyres may change your vehicle as follows: – it may mean that your vehicle no longer conforms to current regu- lations; –...
Page 199 TYRES (4/4) Use in winter Snow or Winter tyres We would recommend that these be Chains fitted to all four wheels to ensure that 2-wheel drive version (2WD) your vehicle retains maximum adhe- sion. Snow chains must be fitted to the front wheels.
Page 200: Front Lights
FRONT LIGHTS: changing bulbs (1/4) The bulbs detailed below can be re- Do not touch the bulb glass. Hold it placed. However, we recommend that by its base. these be replaced by an approved It is essential to use anti-UV bulbs so dealer if this proves difficult.
Page 201 FRONT LIGHTS: changing bulbs (2/4) Front side light Remove bulb holder 7. Remove bulb 8. Bulb type: W5W. Remove cover A. When the bulb has been changed, make sure you refit cover A correctly. The engine may be hot The bulbs are under pres- during operations in close sure and can break when To comply with local legislation, or...
Page 202 FRONT LIGHTS: changing bulbs (3/4) Main beam headlights Direction indicator lights Remove cover B. Turn bulb holder C fully anticlockwise and remove it. Release spring 9 and remove bulb 12 with connector 10. Replace bulb 14. Unclip the bulb from its connector. Bulb type: PY21W.
Page 203 FRONT LIGHTS: changing bulbs (4/4) Daytime running light, front side light Turn the bulb holder a quarter of a turn 16 and take out the bulb. Bulb type: W21/5W. Direction indicator lights Turn the bulb holder 19 a quarter of a turn and take out the bulb.
Page 204: Fog Lights
FOG LIGHTS: changing bulbs Additional lights If you wish to fit fog lights to your ve- hicle, please see an authorised dealer. Any operation on (or modi- fication to) the electrical system must be performed by an approved Dealer Front fog lights 1 Rear fog lights 2 since an incorrect connection might (depending on vehicle)
Page 205: Rear Lights
REAR LIGHTS: replacing the bulbs (1/5) Rear lights 7 Reversing light Pear-shaped bayonet bulb P 21 W Open the tailgate and unscrew the nuts 1, then release the light unit 2 by Rear fog light pulling it out. (depending on vehicle) Release the clips 3 to remove the bulb Pear-shaped, bayonet type P 21 W holder 4.
Page 206 REAR LIGHTS: replacing the bulbs (2/5) Open the luggage compartment lid and 15 Reversing light unscrew the nuts 1, then release the Pear-shaped, bayonet type bulb P light unit 8 by pulling it out. 21 W. Unlock the clips 10 and release the Refitting connectors 11 to remove the bulb hold- To refit, proceed in the reverse order,...
Page 207 REAR LIGHTS: replacing the bulbs (3/5) Open the luggage compartment lid and 22 Reversing light unscrew the nuts 16, then release the Pear-shaped bayonet bulb P 21 W light unit 17 by pulling it out. Rear fog light Unlock the clips 18 to remove the bulb (depending on vehicle) holders 19.
Page 208 REAR LIGHTS: replacing the bulbs (4/5) High-level brake light Carefully unclip tab 27 (movement A) Remove bulb 28. and turn it an eighth of a turn (move- Bulb type: W 16 W. The bulb for high-level brake light 24 ment B) to release bulb holder 26. may be accessed through the luggage compartment.
Page 209 REAR LIGHTS: replacing the bulbs (5/5) Number plate light Unclip light 29 by pressing tab 30 using a flat-blade screwdriver or similar. Unclip lens 32 and take out bulb 31. Bulb type: W 5 W. 5.25...
Page 210 INDICATOR LIGHTS: changing bulbs Unclip indicator light 1 (using a flat- blade screwdriver or similar positioned at A to move the indicator light towards the outside of the vehicle). Turn bulb holder 2 a quarter of a turn (movement B) and take out bulb 3 (movement C).
Page 211 INTERIOR LIGHTING: changing bulbs (1/4) Courtesy light A Front map reading lights (depending on the vehicle) Unclip lens 1 using a flat-blade screw- driver or similar. Remove the lens 1 using a tool such as a flat-blade screwdriver. Remove the bulb concerned. Remove the bulb concerned.
Page 212 INTERIOR LIGHTING: changing bulbs (2/4) Rear map reading lights (depending on the vehicle) Unclip the lens 4 or 6 using a flat-blade screwdriver or similar. Remove the bulb concerned. Bulb type 5: W5W. Bulb type 7: C8W. The bulbs are under pres- sure and can break when replaced.
Page 213 INTERIOR LIGHTING: changing bulbs (3/4) Glove box light Press the tab 9 to release the lens 11 and gain access to the bulb 10. (depending on the vehicle) Bulb type 10:W5W. Unclip the light 8 using a flat-blade screwdriver or similar, by pressing on the tab to move the light towards the inside of the unit.
Page 214 INTERIOR LIGHTING: changing bulbs (4/4) Luggage compartment light Press the tab 14 to release the lens 15. Remove the bulb 16. Bulb type 16:W5W. Unclip the light 12 using a flat-blade screwdriver or similar, by pressing on the tab 13 to move the light towards the inside of the boot.
Page 215: Fuses
FUSES (1/10) Passenger compartment fuses Tweezers 2 If any electrical component does not Remove the fuse using tweezers 2, lo- work, check the condition of the fuses. cated at the back of flap A. Unclip flap A using notch 1 to help you. To remove the fuse from the tweezers, Depending on the vehicle, to identify Check the fuse in question...
Page 216 FUSES (2/10) Fuses in engine compartment B Special features of LPG versions Some functions are protected by fuses The specific LPG circuit shut-off fuse 3 located in the engine compartment is located in the box B. (unit B). However, because of their reduced accessibility, we advise you to have your fuses replaced by an approved dealer.
Page 217 FUSES (3/10) Allocation of fuses in the passenger compartment, left-hand drive vehicles (the presence of certain fuses DEPENDS ON THE VEHICLE EQUIPMENT LEVEL) 5.33...
Page 218 FUSES (4/10) Number Allocation Number Allocation Number Allocation Driver’s side window Rear fog lights Daytime running lights winder Horn Brake lights 4-wheel drive (4WD) transmission Injection, instrument panel Automatic door locking or dashboard, passenger compartment, sequential gearbox lever Rear accessories socket ABS-ESC, brake switch, clutch switch Passenger compartment...
Page 219 FUSES (5/10) Number Allocation Number Allocation Passenger compartment Front windscreen wiper Passenger compartment Passenger compartment ventilation Direction indicator lights 27 and Steering column control Not used Not used Instrument panel Radio, passenger compartment air conditioning control panel, Check the fuse in question passenger compartment and replace it, if necessary, ventilation, rear...
Page 220 FUSES (6/10) Allocation of fuses in the passenger compartment, right-hand drive vehicles (the presence of certain fuses DEPENDS ON THE VEHICLE EQUIPMENT LEVEL) 5.36...
Page 221 FUSES (7/10) Number Allocation Number Allocation Number Allocation Driver’s side window Rear electric windows Brake lights winder Rear fog lights 4-wheel drive (4WD) Injection, instrument panel transmission or dashboard, passenger compartment, sequential Horn gearbox lever Rear air conditioning Automatic door locking Rear accessories socket Airbag Passenger compartment...
Page 222 FUSES (8/10) Number Allocation Number Allocation Passenger compartment Front windscreen wiper Passenger compartment Not used ventilation Direction indicator lights 27 and Steering column control Not used Not used Instrument panel Radio, passenger compartment air conditioning control panel, Check the fuse in question passenger compartment and replace it, if necessary, ventilation, rear...
Page 223 FUSES (9/10) Allocation of fuses in the passenger compartment (the presence of certain fuses DEPENDS ON THE VEHICLE EQUIPMENT LEVEL) Symbol Allocation Symbol Allocation Symbol Allocation Left-hand dipped beam ñ Heated seats headlight Radio î Heated door mirrors Right-hand dipped beam headlight Brake lights ß...
Page 224 FUSES (10/10) Allocation of fuses in the passenger compartment (the presence of certain fuses DEPENDS ON THE VEHICLE EQUIPMENT LEVEL) Symbol Allocation Automatic gearbox GAS fuel 4-wheel drive (4WD) transmission Check the fuse in question and replace it, if necessary, with a fuse of the same rating.
Page 225: Battery: Troubleshooting
BATTERY: troubleshooting (1/2) To avoid all risk of sparks: Connecting a battery charger – Ensure that any consumers (cour- The battery charger must be com- tesy lights, etc.) are switched off patible with a battery with nominal before disconnecting or reconnect- voltage of 12 volts.
Page 226 BATTERY: troubleshooting (2/2) Starting the vehicle using the battery from another vehicle If you have to use the battery from an- other vehicle to start, obtain suitable jump leads (with a large cross section) from an approved dealer or, if you al- ready have jump leads, ensure that they are in perfect condition.
Page 227: Radio Frequency Remote Control: Batteries
RADIO FREQUENCY REMOTE CONTROL: batteries Replacing the remote control Replace battery 2 according to the di- rection marked on the cover. battery Note: It is not advisable to touch the Undo screw 1 to remove the remote electronic circuit in the key cover when control cover.
Page 228: Wiper Blades
WIPER BLADES Check the condition of the wiper blades. You are responsible for their service life: – clean the blades, windscreen and rear screen regularly with soapy water; – do not use them when the wind- screen or rear screen are dry; –...
Page 229: Towing: Breakdown
TOWING: breakdown (1/3) Before any towing, put the gears into neutral (neutral position for vehicles equipped with a manual gearbox or N position for vehicles equipped with an automatic gearbox). Unlock the steering column; the igni- tion key must be in “M” position (ig- nition) to enable signalling (“Stop”...
Page 230 TOWING: breakdown (2/3) Off-road recovery If your vehicle is stuck in sand, snow or mud, attach a flexible towing device (towing belt or other device specially designed for this purpose) to the front or rear towing point (refer to the in- formation on “Front and rear towing points”...
Page 231 TOWING: breakdown (3/3) Towing a vehicle with an automatic gearbox When the engine is switched off, the gearbox is no longer lubricated. It is If the lever is locked in P, preferable to tow this type of vehicle even though you are de- on a trailer or, for 4x2 (2WD) vehicles pressing the brake pedal only, tow it with the rear wheels off the...
Page 232 FITTED AUDIO EQUIPMENT Radio location 1 Location for front speaker 2 or rear speaker 3 If your vehicle is not fitted with an audio system, one can be fitted and locations Unclip the cover using a flat-blade have been provided for: screwdriver or similar.
Page 233: Accessories
ACCESSORIES Electrical and electronic accessories Before installing this type of accessory (particularly for transmitters/receivers: frequency bandwidth, power level, posi- tion of the aerial, etc.), make sure it is compatible with your vehicle. Consult an authorised dealer. Connect accessories with a maximum power of 120 Watts only. Fire hazard. No work may be carried out on the vehicle’s electrical or radio circuits, except by authorised dealers: an incorrectly connected system may result in damage being caused to the electrical equipment and/or the components connected to it.
Page 234: Operating Faults
OPERATING FAULTS (1/5) The following advice will enable you to carry out quick, temporary repairs. For safety reasons you should always contact an approved dealer as soon as possible. The starter is activated POSSIBLE CAUSES WHAT TO DO Warning lights dim or fail to come on; Battery terminals disconnected, Retighten them, reconnect them or clean the starter does not run.
Page 235 OPERATING FAULTS (2/5) On the road POSSIBLE CAUSES WHAT TO DO Vibrations. Tyres not inflated to correct pres- Check the tyre pressures; if this is not the cause, have sures, incorrectly balanced or their condition checked by an approved dealer. damaged.
Page 236 OPERATING FAULTS (3/5) On the road POSSIBLE CAUSES WHAT TO DO Abnormal white smoke from the ex- Mechanical fault: damaged cylinder Stop the engine. haust head gasket. Contact an approved dealer. This is not necessarily a fault. Please refer to the information on “Special Smoke may be caused by features of diesel versions”...
Page 237 OPERATING FAULTS (4/5) On the road POSSIBLE CAUSES WHAT TO DO Whistling Roof aerial poorly positioned. Position the aerial. The engine overheats. The coolant Engine cooling fan not working. Stop the vehicle, switch off the engine and temperature indicator light comes contact an approved dealer.
Page 238 OPERATING FAULTS (5/5) Electrical equipment POSSIBLE CAUSES WHAT TO DO The wipers do not work. Wiper blades stuck. Free the blades before using the wipers. Faulty electrical circuit. Consult an approved dealer. The wiper does not stop. Faulty electrical controls. Consult an approved dealer.
Page 239 Section 6: Technical specifications Vehicle identification plate ............Engine identification plate .
Page 240: Vehicle Identification Plate
VEHICLE IDENTIFICATION PLATE Quote the details given on identifica- Vehicle identification plate A 5 GTW (Gross train weight: vehicle tion plate A on all letters or orders. fully loaded, with trailer). The presence and location of the infor- mation depends on the vehicle. 6 MPAW (Maximim Permissible Weight) for front axle.
Page 241: Engine Identification Plate
ENGINE IDENTIFICATION PLATES (1/2) Quote the information on the identi- fication plate or label A in all corre- spondence or when ordering parts. (Location varies depending on engine) 1 Engine type. 2 Engine suffix. 3 Engine number.
Page 242 ENGINE IDENTIFICATION PLATES (2/2) Please quote the information on the engine plate or label A in all corre- spondence or orders. (Location varies depending on engine) 1 Engine type. 2 Engine suffix. 3 Engine number.
Page 243: Dimensions
DIMENSIONS (in metres) 0.822 2.673 0.820 1.560 4.315 1.634 (1) 1.690 (2) 1.567 1.822 (1) unladen, without roof bars (2) unladen, with roof bars...
Page 244: Engine Specifications
ENGINE SPECIFICATIONS Versions 1.6 16V 1.6 16V 2.0 16V 1.2 16V 1.5 dCi Engine type H5Ft (see engine plate) Cubic capacity (cc) 1,598 1598 1 998 1 198 1,461 Type of fuel Petrol Diesel Octane rating The use of unleaded petrol is essential, with the octane rating as The label located in the stated on the label inside the fuel filler flap.
Page 245 WEIGHTS (in kg) The weights shown are for a basic vehicle without options: they will vary depending on the equipment level of your vehi- cle. Please consult an authorised dealer. Versions Weights shown on the vehicle identification plate (refer to the Maximum permissible all-up weight (MMAC) information on “Vehicle identification plates”...
Page 246 SPARE PARTS AND REPAIRS Original parts are based on strict specifications and are subject to highly-specialised tests. Therefore, they are of at least the same level of quality as the parts fitted originally. If you always fit genuine replacement parts to your vehicle, you will ensure that it performs well. Furthermore, repairs carried out within the manufacturer’s Network using original parts are guaranteed according to the conditions set out on the reverse of the repair order.
Page 247: Service Sheets
SERVICE SHEETS (1/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp □ Service □ ........Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp □ Service □...
Page 248 SERVICE SHEETS (2/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp □ Service □ ........Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp □ Service □...
Page 249 SERVICE SHEETS (3/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp □ Service □ ........Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp □ Service □...
Page 250 SERVICE SHEETS (4/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp □ Service □ ........Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp □ Service □...
Page 251 SERVICE SHEETS (5/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp □ Service □ ........Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp □ Service □...
Page 252 SERVICE SHEETS (6/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp □ Service □ ........Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp □ Service □...
Page 253: Anticorrosion Check
ANTICORROSION CHECK (1/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.15...
Page 254 ANTICORROSION CHECK (2/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.16...
Page 255 ANTICORROSION CHECK (3/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.17...
Page 256 ANTICORROSION CHECK (4/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.18...
Page 257 ANTICORROSION CHECK (5/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.19...
Page 258 6.20...
Page 259 ALPHABETICAL INDEX (1/5) changing gear ..........2.29, 2.45 → 2.48 ABS ...............2.34 → 2.37 child booster seat ..........1.25 → 1.27 child restraint/seat ..........1.25 → 1.35 accessories................ 5.49 child safety....1.2, 1.9 – 1.10, 1.25 → 1.35, 3.9 → 3.11 accessories socket ............3.15 adjusting your driving position .......1.15 →...
Page 260: Maintenance
ALPHABETICAL INDEX (2/5) engine fuel priming bulb ..............1.75 fuel tank ..............1.70 → 1.75 technical specifications ..........6.6 engine coolant ..............4.9 fuel tank capacity ............... 1.70 fuses ..............5.31 → 5.40 engine immobiliser............. 1.11 engine immobiliser (switch) ..........2.2 engine oil ................4.4 engine oil grade ............4.5 →...
Page 261: Practical Advice
ALPHABETICAL INDEX (3/5) map reading lights ..........3.12 – 3.13 keys ................1.2 – 1.3 methods of restraint in addition to the front seat belts ....1.20 → 1.22, 1.24 mirrors ................3.14 levels ..............4.4, 4.8 → 4.10 multimedia equipment ............3.30 levels: coolant ................
Page 262: Technical Specifications
............... 5.43 tanks and reservoirs: remote control door locking unit ........1.2 → 1.4 windscreen washer ............4.10 technical specifications ........6.2, 6.6 → 6.8 RENAULT ANTI-INTRUDER DEVICE (RAID) ..... 1.8 replacement parts ..............6.8 telephone ................3.30 reverse gear towing .................. 6.7 breakdown ............5.45 →...
Page 263: Alphabetical Index
ALPHABETICAL INDEX (5/5) warning buzzer ..............1.65 warning lights........1.44 → 1.53, 1.52 → 1.59 washing ..............4.16 – 4.17 weight .................. 6.7 weights ................6.7 wheelbrace ................5.2 windows ..............3.9 → 3.11 windscreen washer ........1.68 – 1.69, 4.10 wiper blades ..............
Page 266 à999107640Rö ê î ä RENAULT S.A.S. SOCIÉTÉ PAR ACTIONS SIMPLIFIÉE AU CAPITAL DE 533 941 113 € / 13-15, QUAI LE GALLO 92100 BOULOGNE-BILLANCOURT R.C.S. NANTERRE 780 129 987 — SIRET 780 129 987 03591 / TÉL. : 0810 40 50 60...

Renault DUSTER Driver's Handbook Manual

Table of Contents

Section 2: Driving

Section 3: Your Comfort

Section 4: Maintenance

Section 5: Practical Advice

Section 6: Technical Specifications

Quick Links

Chapters

Need help?

Questions and answers

Related Manuals for Renault DUSTER

Summary of Contents for Renault DUSTER

Table of Contents