Subscribe to Our Youtube Channel
Summary of Contents for jbc JCB-D800-2
- Page 1 SAFETY AND OPERATING MANUAL Hammer Drill JCB-D800-2 Original instruCtiOns SO53 3LE Customer Helpline 0845 600 5526...
-
Page 3: General Power Tool Safety Warnings
general POwer tOOl safety warnings warning! read all safety There is an increased risk of warnings and all instructions. electric shock if your body is Failure to follow the warnings and grounded. instructions may result in electric c) Do not expose power tools shock, fire and/or serious injury. -
Page 4: Power Tool Use And Care
safety shoes, hard hat, or hearing use the correct power tool for protection used for appropriate your application. The correct conditions will reduce personal power tool will do the job better injuries. and safer at the rate for which it c) Prevent unintentional starting. - Page 5 to control. g) use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
- Page 6 aDDitiOnal safety POints fOr yOur Hammer Drill 1. Remove the plug from the hidden wiring. Contact with a socket before carrying out “live” wire will also make exposed any adjustment, servicing or metal parts of the tool “live” and maintenance. result in operator injury.
- Page 7 symBOls To reduce the risk of injury, user must read instruction manual Double insulation Warning Wear ear protection Wear eye protection Wear dust mask Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.
-
Page 8: Component List
COmPOnent list 1. KeyeD CHuCK 2. auXiliary HanDle 3. gear BOX switCH 4. fOrwarD anD reVerse rOtatiOn COntrOl 5. On/Off switCH 6. switCH lOCK-On ButtOn 7. DePtH stOP 8. Hammer Or Drill seleCtOr 9. CHuCK Key (see 6 ) SO53 3LE Customer Helpline 0845 600 5526... -
Page 9: Technical Data
teCHniCal Data Voltage 230V-240V~50Hz Rated power 800W Gear 1 0-1,300/min Rated no load speed Gear 2 0-2,700/min Gear 1 0-20800bpm Rated impact rate Gear 2 0-43200bpm Protection class Chuck capacity max. 13mm Steel 13mm Drilling capacity Masonry 20mm Wood 40mm Machine weight 2.4Kg nOise infOrmatiOn... - Page 10 How the tool is used and the materials being cut or drilled. The tool being in good condition and well maintained. To use the correct accessory for the tool and ensure it is sharp and in good condition. The tightness of the grip on the handles and if any anti vibration accessories are used. And the tool is being used as intended by its design and these instructions.
-
Page 11: Intended Use
OPerating instruCtiOns nOte: Before using the tool, read the safety and operating manual carefully. intenDeD use The machine is intended for impact drilling in brick, concrete and stone as well as for drilling in wood, metal and plastic. 1. On/Off switCH Depress to start and release to stop your tool. -
Page 12: Auxiliary Handle
4. auXiliary HanDle Slide the handle onto the drill and rotate to the desired working position. To clamp the auxiliary handle rotate the handgrip clockwise. To loosen the auxiliary handle, rotate the hand grip anti- clockwise. Always use the auxiliary handle (See 3 ). - Page 13 8. gear BOX switCH Choose position 1 for high torque/low speed range for large diameter drill bits and screw driving. Choose position 2 for low torque/ High-speed range for small diameter drill bits. If the gears do not engage easily then rotate the chuck by hand to align the gears.
-
Page 14: Working Hints For Your Hammer Drill
wOrKing Hints fOr yOur Hammer Drill If your hammer drill becomes too hot, set the speed to maximum and run no load for 2-3 minutes to cool the motor. Tungsten carbide drill bits should always be used for concrete and masonry. When drilling in metal, only use HSS drill bits in good condition. - Page 15 Plug rePlaCement (uK & irelanD Only) If you need to replace the fitted plug then follow the instructions below. imPOrtant The wires in the mains lead are colored in accordance with the following code: Blue – neutral Brown – live As the colors of the wires in the mains lead of this appliance may not correspond with the colored markings identifying the terminals in your plug, proceed as follows.
-
Page 16: Warranty Statement
warranty statement Cutting edge construction technology in your hands In 1945 JCB began producing construction equipment. Today, we build the world’s number one diggers, each one the product of our unswerving focus on innovation, quality and engineering. JCB power tools are built to give you the same world beating standards of performance. -
Page 17: Ec Declaration Of Conformity
DeClaratiOn Of COnfOrmity Positec Power tools rg24 8al, uK Declare that the product Description JCB Hammer Drill Type (JCB-D800-2) Function Boring holes in various materials Complies with the following Directives, EC Machinery Directive 2006/42/eC EC Low Voltage Directive 2006/95/eC...
Need help?
Do you have a question about the JCB-D800-2 and is the answer not in the manual?
Questions and answers