1. Manuals
  2. Brands
  3. Toro Manuals
  4. Lawn Mower
  5. 73570
  6. Setup instructions

Toro 73570 Setup Instructions

Hide thumbs Also See for 73570:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Operator's Manual

Loose Parts

Note:
Use the chart below to identify parts for assembly.
DESCRIPTION
Rear Wheel
Wheel Bolt
R.H. Wheel Spindle
L.H. Wheel Spindle
Unplated Thrust Washer – 1.56" O.D x .06"
Thick
Plated Wheel Washer –1.50" O.D x .05" Thick
Bolt – 5/16"-18 x 2.25" Long
Hex Nut – 5/16"-18
Spindle Cap
Front Wheel
Hubcap Washer – 2.50" O.D x .05" Thick
Cotter Pin –.156" x 1.50" Long
Shim Washer – 1.50" O.D x .015" Thick
Hubcap
Steering Wheel
Boot Washer
Nut
Lock Washer
Trim Cover
Seat Assembly
Shoulder Bolt – 5/16"
Locknut – 5/16"
Printed in USA
520xi GARDEN TRACTOR
MODEL NO. 73570–9900001 & UP
QTY.
2
10
1
1
2
4
2
2
2
2
2
2
2
2
1
1
1
1
1
1
2
2
The Toro Company – 1998
All Rights Reserved
INSTRUCTIONS
USE
Installing the rear wheels
Installing the front wheels
Installing the steering wheel
Installing the seat
FORM NO. 3321–971
SET UP

Advertisement

Table of Contents
loading

Related Manuals for Toro 73570

Summary of Contents for Toro 73570

  • Page 1: Loose Parts

    FORM NO. 3321–971 520xi GARDEN TRACTOR SET UP MODEL NO. 73570–9900001 & UP INSTRUCTIONS Loose Parts Note: Use the chart below to identify parts for assembly. DESCRIPTION QTY. Rear Wheel Installing the rear wheels Wheel Bolt R.H. Wheel Spindle L.H. Wheel Spindle Unplated Thrust Washer –...

  • Page 2: Installing The Rear Wheels

    Set-Up Instructions DESCRIPTION QTY. Bolt – 1/4”-20 x .88” Long Hex Nut – 1/4”-20 Attaching the battery cables Flat washer, 1/4” Grille Screw – #8 x .50” Long Securing the grille Grille Washer – .75” O.D. Hitch Pin Hairpin Cotter Installing the drawbar hitch pin Flat Washer –...
  • Page 3 Set-Up Instructions Note: Remove, or be careful not to damage, Insert a 1.50” O.D x .05” thick plated wheel the two upper grille grommets (Fig. 2). washer onto the R.H. spindle (Fig. 4). Using a suitable hoist, raise the front of the Install a front wheel onto the R.H.
  • Page 4 Set-Up Instructions 11. Secure the wheel to the spindle with a cotter pin. Bend the ends of the cotter pin completely around the spindle. 12. Install a hubcap onto the hubcap washer until it snaps in place (Fig. 4). 13. Look at the end of the steering arm and the inside edge of the tire.

  • Page 5: Installing The Seat

    Set-Up Instructions Installing the Seat Install the steering wheel onto the shaft, carefully aligning the splines (Fig. 8). Mount the seat to the seat base using two 5/16” Note: Be sure to align steering wheel in the shoulder bolts and lock nuts (Fig. 7). straight ahead position.

  • Page 6: Checking Front Wheel Toe-In

    Set-Up Instructions Check to Insure that the Checking Front Wheel Toe–In Steering Linkage is Centered With the tractor on a level surface, check to make sure the front wheel toe-in is between 1/8” and 1/4”. With the tractor on a level surface, turn the For instructions on adjusting toe-in, refer to the steering wheel fully to the left and check the Maintenance section in Operator’s Manual.

  • Page 7: Installing The Drawbar Hitch Pin

    Set-Up Instructions Remove the filler caps from the battery. Slowly pour electrolyte into each cell until the electrolyte level is up to the lower part of the tube (Fig. 10). Use an electrolyte with a specific gravity of 1.265. 1254 Figure 11 1262 1.

  • Page 8: Test Driving The Tractor

    Set-Up Instructions Let the load come to a full stop, then engage again. Repeat these procedures (1 and 2) 5 times. Test Driving the Tractor Check the oil level in the crankcase (refer to Engine Oil in your tractor Operator’s Manual for oil type, viscosity and crankcase capacity).

Table of Contents