1. Manuals
  2. Brands
  3. Sebart Manuals
  4. Toy
  5. Sukhoi 29S 50E ARF
  6. Assembly manual

Sebart Sukhoi 29S 50E ARF Assembly Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

SebArt
New
The new Sukhoi
pilot, Sebastiano Silvestri and the design is based on of his new
Tournament Of Champion's competition airplane.
This professional ARTF kit is the result of Sebastiano's long
research in 3D performance. This combined with an extremely
lightweight structure, the all wood airframe, the big control
surfaces and the new revolutionary Lift Generator on landing
gear give the Sukhoi
and crisp control authority at any airspeed and flight
condition....That for this small class of airplane is revolutionary!
The Sukhoi
torque rolls, blenders, waterfalls and almost anything else you can
dream up are waiting you!
.....the only aerobatic limit is your fantasy!
Specifications
Wing Span:.......................
Length:...............................
Wing Area:....................
Weight:......
2.400 g. RTF less battery (84,6 oz)
Radio:......4-Channel with 4 standard servos
Sukhoi
ASSEMBLY MANUAL
S 50E ARF was designed by Italy aerobatic
29
S 50E an impressive thrust-to-weight ratio
29
S 50E can do it all...unbelievable easy harriers,
29
154 cm (61 in.)
154 cm (61 in.)
51,6 dm2 (80 sq.in.)
professional line
29
ARF
Recommended power set up:
Motor:...........................
ESC:.........................
Battery:
FlightPower 3300-6S or 3700-6S
Propeller: ....................
S
50E
Hacker A50-16S
X70 SBec-Pro
APC 16x10E

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Sukhoi 29S 50E ARF and is the answer not in the manual?

Questions and answers

Related Manuals for Sebart Sukhoi 29S 50E ARF

Summary of Contents for Sebart Sukhoi 29S 50E ARF

  • Page 1 SebArt professional line Sukhoi ASSEMBLY MANUAL The new Sukhoi S 50E ARF was designed by Italy aerobatic pilot, Sebastiano Silvestri and the design is based on of his new Tournament Of Champion’s competition airplane. This professional ARTF kit is the result of Sebastiano’s long research in 3D performance.

  • Page 2: Table Of Contents

    Table of contents Table of contents.......................……….. 2 Required radio, motor and battery.....................…. 3 Additional required items, tools and adhesives................3 Warning............................3 Before starting assembly ......................… 3 Using the manual........................... 4 Warranty information…......................... 4 Section 1 – wing fillet installation…....................5 Section 2 –...

  • Page 3: Required Radio, Motor And Battery

    Required radio, motor and battery Radio equipment: • Minimum 4-channel radio system • 4 digital standard servo, recommended JR PROPO DS9401 or DS8301 • 2 servo extension 600mm, for elevator and rudder servos • 2 servo extension 100mm, for aileron’s servos Recommended electric motor for best performance: •...

  • Page 4: Using The Manual

    Rember to take your time and follow the directions. Warranty information SebArt garantees this kit to be free from defects in both material and workmanship at the date of purchase. This warranty does not cover any parts damage by use or modification, and in no case shall SebArt’s liability exceed the original cost of the purchased kit.

  • Page 5: Section 1 - Wing Fillet Installation

    Section 1 – wing fillet installation step 1 Locate the carbon tube and the wing to the fuselage. Locate the corresponding wing fillet to the wing. Test fit the fillet and his alignment with the wing panel and fuselage. step 2 Once satisfied with the fit, glue the wing fillet to the wing panel using medium CA.

  • Page 6: Section 2 - Ailerons Installation

    step 4 Use the covering iron carefully, at a medium temperature, to glue the cover material down around the area of the fillet. Use caution while working around areas where the cover material overlaps to prevent separating the covers. step 5 Repeat steps 1 through 4 for the remaining wing panel and wing fillet.

  • Page 7: Section 3 - Aileron Servo & Control Horn Installation

    step 2 Carefully glue, with some drops of thin CA, each of the four hinges in the aileron. step 3 Locate the aileron and carefully glue, with some drops of thin CA, each of the four hinges into the wing panel. step 4 Work the aileron up and down some times to work the hinges and check for proper movement.
  • Page 8 step 2 Install the servo hardware (gommets and eyelets) and put the servo into the wing panel, as per pictures. step 3 Drill using a 1,5mm drill bit, and install the servo into the wing panel using a Phillips screwdriver.
  • Page 9 step 4 Glue the fibreglass horn with medium CA into the aileron. step 5 Install the hardware and make the final adjustment as per pictures. step 6 Repeat steps 1 through 5 for the remaining wing panel.

  • Page 10: Section 4 - Rudder Installation & Tail Wheel Installation

    Section 4 – rudder installation & tail wheel installation step 1 Test fit the rudder into the fuselage, check for a correct alignment. step 2 Glue it carefully with medium CA. step 3 Insert the three hinges in their appropriate slots and glue them with some drops of thin CA.
  • Page 11 step 4 Drill in the rudder, 20mm from the bottom, the location for the tail wheel using a 2mm drill bit. With the hobby knife cut a groove of 20mm length into the rudder. step 5 Than locate the items included in the hardware pack and assemble them as per picture. step 6 Drill on fuselage the screw locations for the tail wheel using a 1,5mm drill bit, and install it as per picture.

  • Page 12: Section 5 - Elevator Installation

    step 7 Carefully put some drops of medium CA into the 2 mm hole, carefully locate the rudder and glue the hinges with some drops of thin CA. step 8 Work the rudder right and left some times to work the hinges and check for proper movement. Section 5 –...
  • Page 13 step 2 Insert carefully the elevator through the fuselage. step 3 Insert the stabiliser into fuselage space and locate the elevator hinges into the stabiliser. step 4 Glue carefully the hinges in the stabiliser with some drops of thin CA.

  • Page 14: Section 6 - Elevator Servo & Control Horn Installation

    step 5 Locate the carbon tube in his position and carefully check the alignment of the stabilizer with the fuselage, as per pictures. step 6 Once satisfied with the alignment, glue carefully with thin CA the stabilizer at the fuselage. Section 6 –...
  • Page 15 step 2 Than install the servo hardware (gommets and eyelets) and locate the servo into the fuselage. step 3 Drill using a 1,5mm drill bit, and install the servo into the fuselage using a Phillips screwdriver. step 4 Glue the fibreglass horn with medium CA into the elevator. Than install the hardware and make the final adjustment as per picture.

  • Page 16: Section 7 - Rudder Servo & Control Horn Installation

    Section 7 – rudder servo & control horn installation step 1 Locate the following items included in the hardware pack, servo extension 600mm long and servo. step 2 Than install the servo hardware (gommets and eyelets) and locate the servo into the fuselage. step 3 Drill using a 1,5mm drill bit, and install the servo into the fuselage using a Phillips screwdriver.

  • Page 17: Section 8 - Landing Gear & Wheels Installation

    step 4 Glue the fibreglass horn with medium CA into the rudder. Than install the hardware and make the final adjustment as per picture. Section 8 – landing gear & wheels installation step 1 Locate the following items included in the hardware pack.
  • Page 18 step 2 Locate the landing gear on the fuselage and fix it with the screws included in the hardware pack. step 3 Sand with the sanding paper the inside of the wheel pant; locate the wood reinforcement, glue it with some drops of medium CA and drill the location for the wheel axis screw using a 3mm drill bit as per pictures.
  • Page 19 step 5 Drill the location for the wheel pant fixing screw using a 1,5mm drill bit and than fix the wheel pant with the screw included in the hardware pack. step 6 Test fit the L.G. Lift Generator and his alignment with the fuselage. step 7 Glue carefully the landing gear fillet with some drops of medium CA, as per picture.

  • Page 20: Section 9 - Electric Motor Installation

    Section 9 – electric motor installation For best performance, we recommend to use HACKER motor. step 1 Locate the engine mount on the fuselage, fix it using the four screws included in the hardware pack and than glue it carefully with medium CA. step 2 Locate the motor and fix it with the four screws included in the motor hardware pack.
  • Page 21 step 3 Locate and fix the ESC and his switch as per picture. step 4 Glue with some drops of medium CA on side of the Velcro strip included in the hardware pack. step 5 With the hobby knife open the cooling holes in the fuselage as per picture.

  • Page 22: Section 10 - Glow Engine Installation (Option)

    If you want to install a glow engine, you need the hardware pack and the reinforcement wood parts set, that is available as optional. Visit the website WWW.SEBART.IT for price and for download the manual instructions for this special application.
  • Page 23 step 2 Slide the cowling onto the fuselage and install the spinner back plate. Then apply another piece of masking tape on the same line of the one applied before. Drill the location for the four self-tapping screws using a 1.5mm drill bit. step 3 Attach the cowl using the four self-tapping screws, included in hardware pack, and a Phillips screwdriver.

  • Page 24: Section 12 - Final Radio Installation

    Section 12 – final radio installation Install the receiver, two extension 100mm for aileron servos and the battery pack as per the picture. Wings installation Locate the wing panels and fix them using the two nylon screws, included in the hardware pack, and a Phillips screwdriver.

  • Page 25: Decal Set Application

    Decal set application Control throws Please, follow carefully the recommended linkage setups for ailerons and elevators. For the AILERON we recommend the following throws: Low rate: 20° up / 20° down Expo: 40% 3D rate: 45° up / 45° down Expo: 80% For the ELEVATOR we recommend the following throws: Low rate: 20°...

  • Page 26: Rates And Expos

    Finally... Finally... Finally... Finally... have a nice flight! have a nice flight! have a nice flight! have a nice flight! SebArt di Sebastiano Silvestri Via Roma 83/85 38017 Mezzolombardo (TN) – Italy www.sebart.it...

Table of Contents