BikeBerry FH-MEK80 Installation And Operating Manual

Bicycle engine

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

The Highest Quality Bicycles and Engine Kits.

Installation and Operating Guide

Model Numbers:

FHMEK80, FHBEK80, FHMEK80B, FHBEK80B, FHBEK48, FHMEK48, FHBEK48B,

FHMEK48B

PLEASE READ THIS ENTIRE GUIDE BEFORE BEGINNING

Table of Contents

Need help?

Do you have a question about the FH-MEK80 and is the answer not in the manual?

Questions and answers

Summary of Contents for BikeBerry FH-MEK80

Page 1 The Highest Quality Bicycles and Engine Kits. Installation and Operating Guide Model Numbers: FHMEK80, FHBEK80, FHMEK80B, FHBEK80B, FHBEK48, FHMEK48, FHBEK48B, FHMEK48B PLEASE READ THIS ENTIRE GUIDE BEFORE BEGINNING ...
Page 2 IMPORTANT SAFETY INFORMATION When installing a bicycle engine kit, it is always a good idea to double check all screws, nuts, and bolts. All nuts must be screwed on tight in case of vibration that may cause the gaskets to blow. Remember, tightening all screws may very well save your life. DISCLAIMER This manual is for entertainment purposes only. The instructions and procedures provided in this manual is an incomplete draft of unverified and incomplete procedures. This manual is for discussion purposes and should not be construed as authoritative information in any form as to be the equipment depicted within. Author does not warrant or assume legal liability or responsibility for accuracy, safety, completeness, or usefulness of any information, apparatus, product, or process disclosed or referred to. Information is provided for informational purposes only. Any actions or assumptions taken on reader’s part as a result of any information disclosed by Author are taken entirely at reader’s own risk. Furthermore, Author shall not be liable for any loss of profits, contracts, opportunities or any direct, indirect, consequential loss of any kind (including death and/or injury), or loss of property arising out of or in connection with the use of information herein. News items, opinions, and/or statements posed by Author may be unsubstantiated and should be considered as such. The advice and strategies contained herein may not be suitable for your situation. You should consult a professional where appropriate. Kits are not guaranteed to fit specific bike(s). Operating a bike, motorized bicycle or bike with a bicycle engine kit installed involves some risks of serious bodily injury. Buyer accepts responsibility for any and all vehicle operation that may lead to personal injury, economic loss, social distress, other losses, costs and damages resulting from operating this motorized bicycle or bicycle engine kit. Seller is not responsible for misuse of this kit or any warranty after installation. Not all motorized bicycle are allowed on road use. We make no guarantee as to the road legality of these bike motors. BikeBerry.com 18003170479 1 ...
Page 3 BEFORE YOU START This manual will teach you how to install a 2stroke engine kit on a bike. Now before we even start, it’s important to know what you’re getting into and what you need for installation to go as smooth as possible. Even though the engine kit is made to be as universal as possible, you bike should have these key features to ensure easier installation: ● Your bike needs to be a standard men’s beach cruiser, road bike, or hardtail mountain bike. ● The seat and down tube diameter should be 2528mm (11.10in) with an open VStyle frame ● The kit should fit most 26 x 1.75in rear wheel with either 12 or 14 gauge 36 count spokes. BikeBerry.com 18003170479 2 ...
Page 4 If your bike matches these specifications, then you’re ready to go… BikeBerry.com 18003170479 3 ...
Page 5 Engine Block Clutch Lever 16. Fuel Valve (Petcock) NT Carburetor 10. Chain Idler Pulley 17. Sprocket Clamp Assembly Exhaust Muffler 11. 415 HD Drive Chain 18. 44T Drive Sprocket Chain Guard 12. Spark Plug 19. Heat Shield Spring Throttle Cable 13. CDI 20. Extension Clutch Spring Clutch Cable 14. 1.5 or 2.5L Gas Tank 21. Spark Plug Removal Tool Throttle Grip Assembly BONUS: Universal UMount BikeBerry.com 18003170479 4 ...
Page 6 INSTALLATION The Rear Wheel Assembly Tools you’ll need: ● 2x 10mm wrench ● an open wrench ● scissors Step 1: Remove the coaster brake arm. If your bike has a rear coaster brake arm attached to the rear wheel, remove it to install the rear sprocket. Make sure not to accidently disassemble the entire rear hub doing so. Once you remove the coaster brake, remove the dust cover. Step 2: Cut a slit in one of the rubber grommets BikeBerry.com 18003170479 5 ...
Page 7 Cut a straight line between any two holes and thread it through the rear hub. Check to see if all the holes are visible through the spokes. If a spoke is covering any of the 9 holes, you will not be able to use that rear wheel. You will have to find a replacement that is compatible. Step 3: Alignment check Place the second rubber grommet outside of the spokes and align both grommets together so the 9 holes match up evenly. Step 4: Align the assembly. This step is the longer and most time consuming portion of the installation. Place the second rubber grommet on top of the 44 tooth rear sprocket. It doesn’t matter which way the 44T sprocket is facing. Then start pushing all 9 bolts through the assembly. Line up the assembly with the rubber grommet inside the hub and thread the 3way plates behind the entire assembly. Make sure one of the 3 plates is placed over the cut made on the first rubber grommet. BikeBerry.com 18003170479 6 ...
Page 8 Add 9 washers on each bolt and thread the 9 nuts hand tight. Step 5: Torquing the bolts and nuts and Truing your sprocket adapter assembly. This is the portion of the installation where it requires the most patience and frequent adjustment when tightening down your assembly. You want to torque each bolt as tight and evenly as possible without bending the spokes. The key is to torque down each bolt in a STAR pattern to keep the the sprocket alignment true. Think of tightening each bolt down in phases, making sure each bolt is torqued down evenly. As you tighten up your bolts each time, keep watch of your center sprocket. Make sure it still stays centered throughout this process or else risk having to untighten and retighten bolts to keep your sprocket centered and aligned. Once it gets tighter and tighter, you’ll notice any overlap you encountered with the metal plates will disappear. BikeBerry.com 18003170479 7 ...
Page 9 Step 6 (OPTIONAL): Reinstall your coaster brake arm. Make sure your coaster brake arm can clear the 9 bolts from your assembly. To make sure it has enough clearance, dryfit your coaster brake arm back to the wheel and rotate it around the bolts. If it clears, then you can use your coaster brake arm. If it doesn’t, we recommend skipping this step and installing caliper brakes. Unfortunately there are some rear wheels that are not compatible with this sprocket adapter assembly. O ur best recommendation is using a BBR Tuning rear sprocket adapter for ease of installation and better coaster brake clearance. Alternatively, you can bend a 90 degree angle into your coaster brake arm to provide clearance. Ultimately, more stopping power is highly recommended. Getting a Rear, Front or both caliper brakes is best for your safety. Step 7: Reinstall the rear wheel and bike chain back on your bike. BikeBerry.com 18003170479 8 ...
Page 10 Once the sprocket is tight, spin the wheel and check that the sprocket runs true. Deviation can be no more than 1.5mm both ways. Any sidetoside excess deviation can be corrected by spinning the wheel and then tightening the sprocket where needed in order to get correct alignment. Make sure bolts are tight. Notice the concavity or indentation of teeth of the rear sprocket is inward towards spokes. This helps keep the chain closer to the inside of the wheel and spokes and allows for better clearance of the rear stays of the bicycle frame. BikeBerry.com 18003170479 9 ...
Page 11 MOUNTING THE ENGINE Notes Before Mounting your Engine Engine mounting can go 1 of 2 ways: Easy or Challenging This all depends on your bike frame. Example #1 Easy An old style beach cruiser frame will more than likely be the easiest fit for a Flying Horse or Mega Motors engine kit. Old style beach cruisers have the same size (diameter) top tube, down tube, and seat tube. Another reason why old style beach cruisers are the easiest to install a motor on is because the pedal cranks are centered below the seat post. You’ll know why this is important in a minute… BikeBerry.com 18003170479 10 ...
Page 12 Example #2 EasyMedium New Style Beach Cruisers (from 2005 and on) have larger down tube diameter, larger top tube diameter, and/or forward pedaling crank position. If you have an old style bicycle, please continue reading. If you have a new style bicycle with the following: ● Only a larger down tube, please go to page 12. ● Combination of both larger down tube and pedaling cranks, please go to page 15. Mounting an Engine on Older Style Frames: 1. Remove rear and front engine mount hardware from the engine block. 2. Align the engine block on your frame. 3. Make sure the engine is angled where the tip of the intake manifold sits parallel with the ground. BikeBerry.com 18003170479 11 ...
Page 13 4. Reinstall front and rear mounting hardware. Make sure the rear and front mounts sit flush with the bicycle frame. When installing the hardware, put in the washers first, then the lock washer, and then thread the nut. Mounting an Engine with a Larger Down Tube: 1. Requires: Universal Mounting Bracket 2. Disassemble the Universal Mounting UMount BikeBerry.com 18003170479 12 ...
Page 14 3. Remove all mounting hardware from front and rear mounting studs. 4. Remove front mounting studs from engine block. You can use 1 of the 2 following techniques to accomplish this: a. Use a vicegrip to remove the front mounting studs b. Thread 2 nuts on both front mounting studs and torque the jam nut to loosen the the mounting stud. BikeBerry.com 18003170479 13 ...
Page 15 5. Align the UMount plate with the holes from the front mount. 6. Thread the UMount bolts through the plate a. Optional: Use locktite on the bolt threads to secure the assembly. 7. Place and Align the engine block in the bicycle frame. 8. Make sure the tip of the manifold intake is parallel with the ground. This is important for proper fuel consumption. If it’s angled, you’ll have problems feeding your motor air and fuel. 9. Install the rear mount hardware, but only hand tight for now. We are now going to adjust the front mount. 10. Install UBracket and thread washer and nuts tight a. Option, use lock tight to secure nuts. 11. Install rear motor mount hardware to complete the engine mount. BikeBerry.com 18003170479 14 ...
Page 16 Mounting an Engine with Forward Pedaling Cranks + Larger Down Tube 1. Requires: JNM Vibration Motor Mount + Heavy Duty Universal UMount 2. Remove all mounting hardware from front and rear mounting studs. BikeBerry.com 18003170479 15 ...
Page 17 3. Remove front and rear mounting studs from engine block. You can use 1 of the 2 following techniques to accomplish this: a. Use vicegrip to remove the front and rear mounting studs. b. Thread 2 nuts on both front and rear mounting studs and torque the jam nut to loosen the mounting stud. BikeBerry.com 18003170479 16 ...
Page 18 4. Install the extended front and rear studs from the JNM Vibration Motor Mount assembly. a. option: Use Locktite to secure studs inside engine block. 5. Then thread the rear mounting bracket and both front and rear rubber mount. BikeBerry.com 18003170479 17 ...
Page 19 6. Position Engine inside the bike frame. Make sure the intake manifold is parallel with the ground 7. Take the HD UMount plate and thread the top hole pattern through the front motor mount. 8. Place 1 of the 2 U brackets on the bottom hold patterns over the larger down tube. 9. Thread the washer, locking washer and nuts for the front mount. 10. Thread the remaining rear mount assembly for the rear mounting studs. BikeBerry.com 18003170479 18 ...
Page 20 Installing the Clutch Assembly Tool Required: ● Open Wrench ● Screwdriver or Allen Keys/Wrench Required parts: clutch cable, clutch lever, the heat shield spring and the extension spring. BikeBerry.com 18003170479 19 ...
Page 21 1. Remove any preexisting grip handles on your handlebar and thread the clutch lever on the left side of your handlebar. 2. The clutch cable has 2 different looking ends. Take the side with the nipple piece and install the clutch cable into the clutch lever by threading the nipple piece into the clutch lever nipple housing. BikeBerry.com 18003170479 20 ...
Page 22 3. Thread the heat shield spring on the opposite side of the clutch cable. 4. Thread the wire itself through the clutch base screw located right under the intake manifold. 5. Once it’s threaded through the clutch base screw, thread the extension spring through the clutch cable. 6. Lastly, thread the clutch cable through the clutch arm on the engine. Make sure you unthread the screw that will hold the clutch cable in place. 7. Once you threaded the cable through the clutch arm, make sure you pull on the clutch cable for a stronger tension, while you rethread the clutch screw into the clutch arm. 8. Operate the clutch lever to make sure your clutch arm swings towards the motor. The key for proper installation is making sure the clutch arm is flush with the engine. Once you pull the clutch lever, the clutch arm should move inward towards the motor allowing it to disengage your motor. Once your engine is disengaged, you can pedal freely. With the clutch lever in released, it will engage the motor. Pulling in the clutch lever will have some resistance. This is normal. BikeBerry.com 18003170479 21 ...
Page 23 BikeBerry.com 18003170479 22 ...
Page 24 Installing the Chain Tool requirements: Screwdriver Alan Keys/Wrench Needle Nose Pliers Motorized Bike Chain Breaker 1. Remove the gear case cover. 2. Once removed, unscrew the screw pin and remove the flower nut. a. The easiest way to remove the flower nut is pulling in the clutch lever and disengage the motor. Then press the clutch plate against the engine to free the flower nut to unthread easily. 3. Then remove the clutch plate. You’ll notice that if you spin the 3 pegs sticking out in the middle of the gear, it will also spin the 10T sprocket. BikeBerry.com 18003170479 23 ...
Page 25 4. Remove the clutch case cover. Allow it to hang in place once you remove all the screws. 5. Remove the master link from your 415 HD Chain. 6. Install the chain on both front and rear sprocket. 7. Measure and remove any excess chain for a tight fit. We recommend less than a ½ inch in play. Remove any slack with a motorized bike chain breaker. 8. Reinstall the master link 9. Reinstall the gear case assembly and cover. Then reinstall the clutch case cover. BikeBerry.com 18003170479 24 ...
Page 26 10. Install the Idler Chain Pulley. a. When installing the pulley, the first thing you should do is adjust the idler wheel position so that it is aligned. Then tighten it down on the frame. b. Place the idler on the bicycle frame and tighten it down until it is snug. Make sure it’s not too tight where you can’t adjust it. c. While you’re adjusting the idler pulley, keep 2 things in mind: make sure the chain is tight, only providing no more than ½ inch of slack and make sure the chain is aligned straight for proper chain guidance. d. Once you have those 2 things checked, thread the nuts as tight as possible. Use 2 #mm wrenches for each side. While tightening the idler pulley, it will move side to side and off position so we recommend watching out for any misalignment while tightening your pulley down. BikeBerry.com 18003170479 25 ...
Page 27 BikeBerry.com 18003170479 26 ...
Page 28 Installing the Throttle Assembly Tool requirements: ● permanent marker ● ¼ inch drillbit + drill ● screwdriver. Before installing the throttle handles, you must first remove the preexisting grips on your handlebar. 1. Disassemble your kill switch from the throttle grip handle if not done so already. 2. Take your measuring tape and measure 4¼ inches from the end of the right side of the handlebar. 3. Mark that position with a permanent marker right at the top of the handlebar. 4. Drill a 1mm pilot hole where you marked your handlebar. Then follow it up with a 5mm drill. 5. Thread the throttle cable through the kill switch. Then thread the Lpiece on the kill switch. 6. Then thread the cable button in the grip handle coupling. BikeBerry.com 18003170479 27 ...
Page 29 7. Then install the entire assembly by threading it through the entire handlebar. Insert the kill switch notch in the drilled hole, then screw everything together. You can adjust the Lpiece so it sits more comfortably with the locking nut. NOTE: Care should be taken with the cable and throttle grip handle. If you are too rough with it, you will break it. Be gentle when installing the throttle. 8. (Optional) Install the other handle grip on the left side of the handlebar. BikeBerry.com 18003170479 28 ...
Page 30 Installing the Carburetor The other end of the throttle cable is installed inside the carburetor. 1. NT Carburetor 5. EWasher 2. Screw Top 6. Jet Needle 3. Spring 7. CClip 4. Slide BikeBerry.com 18003170479 29 ...
Page 31 1. Unscrew the carburetor and remove all the internal components: the screw top, the throttle spring, the slide, the CWasher, and the jet needle with an eclip attached. 2. Once removed, reassemble these pieces outside of the carburetor. a. Thread the jet needle through the slide. b. Then drop and align the the Cwasher over the jet needle. Make sure the slit on the Cwasher is aligned with the slit on the slide. c. Then place the spring and then the screw top over the slide. BikeBerry.com 18003170479 30 ...
Page 32 3. Thread the throttle cable through the screw top then through the spring. Push the spring into the screw top to expose the throttle cable. 4. Line the throttle cable up with the slit side of the slide. Thread the throttle cable through the slit and drop the cable’s nipple piece into the slide housing. 5. Once you let go of the spring, the whole assembly should be held in place. 6. Reinstall the assembly back into the carburetor. Make sure you line up the slide slit with the guide peg inside the carburetor. Then screw everything back on tightly. 7. Loosen the manifold clamp and install the carburetor on the intake manifold. BikeBerry.com 18003170479 31 ...
Page 33 Installing the Electrical Assembly There are 3 electrical parts to the engine: The CDI, the Magneto Loop Set, and the Spark Plug. The CDI can be mounted anywhere on the bike as long as it can reach the spark plug. The spark plug is threaded on top of the engine head and the magneto loops set is installed inside the engine. NOTE: When it comes to wiring, you may need to splice your wires together, which involves cutting and stripping the insulation away from the tip of the wires. 1. Remove the spark plug crown before attaching the CDI spark plug cap. WARNING: Fail to remove this crown can damage or ruin the spark plug cap. 2. Once you mount your CDI, install the CDI spark plug cap onto the spark plug. BikeBerry.com 18003170479 32 ...
Page 34 3. Connect the black wire from the CDI to the black wire from the magneto. 4. Connect the blue wire from the CDI to the blue wire from the magneto. 5. Connect the green wire (sometimes black) from the kill switch to the black wire from the CDI. 6. Connect the red and yellow from the kill switch to the blue wires from the CDI. BikeBerry.com 18003170479 33 ...
Page 35 7. (Recommended but Optional) : Check to see if you’re wired properly by removing the spark plug and checking for spark. a. Use the spark plug removal tool to remove the spark plug from the head. If your CDI spark plug cap is installed, remove it before removing the spark plug. b. Engage the motor by releasing the clutch. c. Hold the spark plug against the engine head to ensure visible spark. d. Then hold the rear wheel off the ground and rotate it to create spark. e. If you have spark, you installed it properly. If you do not have spark, please check your wiring. BikeBerry.com 18003170479 34 ...
Page 36 Installing the Muffler Exhaust, Gas Tank & Fuel Assembly Once you have all the major components completed, install the remaining parts. BikeBerry.com 18003170479 35 ...
Page 37 Use this ratio for your first 4 tanks of gas. After BreakIn Fuel Ratio 24:1 (56oz of oil per gallon of gas) Clutch Adjustment Guide Sometimes the clutch bevel wheel inside the motor are too tight due to manufacturing. This will help free your clutch and adjust your clutch assembly for proper use. When adjusting your clutch, please remember to disassemble your rear drive chain from the engine’s 10 tooth sprocket before continuing. 1. Begin by removing your gear case cover. 2. Remove the locking screw holding in your flower nut. 3. Remove the flower nut. 4. Remove the clutch plate and clutch spring, exposing the clutch bevel wheel. Some models do not include the clutch spring. If your model does not, it’s normal. 2Stroke engine kits do not require it. 5. Make sure the bevel wheel is spinning freely. If it is, you’ll be able to move it with your hand. If it does not, tap the 3 studs counterclockwise gently with a rubber mallet. Repeat until clutch bevel wheel spins freely. 6. Assemble the spring and clutch plate the way it was when you started and tighten the flower nut hand tight. NOTE: The way the clutch works is that clutch arm pushes away from the clutch cover away from the clutch pads, freeing the drive chain. When this happens, you’re able to pedal your bike because you disengaged your motor. When the clutch arm is not pulled in, the clutch plate pushes up against the clutch pads and engages the motor. 7. You must adjust the flower nut so the clutch plate moves ⅛ inches when you disengage the motor. If your flower nut is threaded out more than ⅛ inches, your clutch may slip when attempting to start the engine. If it’s less than ⅛ inches, it will be too tight to disengage. Make sure you adjust it just right. 8. Reinstall the locking screw for the flower nut. Then reinstall the gear case gasket and cover. BikeBerry.com 18003170479 36 ...
Page 38 9. If this was done correctly, your clutch should be able to engage and disengage properly. NT Carburetor (aka the Stock Carb) Adjustment Guide If your engine is under performing, these steps should help you solve those issues. The NT carburetors are vey simple and easy to tune. Figuring out the issue may depend on a few factors. Before attempting any carburetor adjustments, make sure your carburetor is clean of any debris, manifold gasket is in good condition, your fuel filter and air filter are not blocked or clogged, your carburetor manifold is well sealed, and the intake manifold nuts are tight. Now for the NT Carburetor adjustment... There’s only 1 direct method in turning these carburetors: Adjust the EClip connected to your jet needle. It has a series of notches at the top that represents different fuel mixtures. You can remove and reposition the Eclip for any desired position. The top notch is for the leanest mixture and the bottom notch (closest to the needle poing) is the richest. So now you know how to adjust it, the next step is figuring out where to adjust it. One main factor that can affect your carburetor is elevation. The higher your elevation, the richer you need to adjust your clutch. BikeBerry.com 18003170479 37 ...
Page 39 8. Clutch Pad 9. Clutch Bevel Gear 10. Lock Nut 11. Spring Gasket PI14 12. Clutch Base Peg 13. Clutch Base 15. 202 Main Bearing 16. Adjustment Nut 17. Main Clutch Spring 18. Clutch Pin Mandrel 19. Flat Key 20. Clutch Shaft 21. Pintle 22. Ferrule 23. 10 Tooth Sprocket 24. Clutch Actuator 25. Shaft Fixed Pin 26. Bucking Bar 27. Clutch Camshaft Bearing 28. Clutch Arm 29. Washer 30. Nylon Lock Nut 33. Extension Spring 35. Clutch Screw Base 36. Clutch Screw Base 37. Heat Shield Spring 38. Clutch Cable Pt. 1 Pt. 2 39. Clutch Lever 40. Clutch Wire Screw 55. Clutch Case Cover BikeBerry.com 18003170479 38 ...
Page 40 1. Gear Case Cover Bolt 2. Gear Case Cover 3. Round Column Bolt 4. Spring Gasket 5. Small Bevel Wheel 6. Small Seal Loop #2 7. Crankcase Bolt 8. Crankcase Bolt #2 9. Crankcase 1 of 2 10. Motor Mount 11. Motor Mount Bracket 12. Rear Mount Washer 13. Rear Mount Nylon 14. Motor Mount Stud 15. Bottom Crank Case 16. Front Motor Mount Lock Nut Body Stud 17. Keyway 18. 202 Main Bearing 19. Crank 20. Crank Bearing 21. Crank Connecting 22. Crank Cover 23. Crank Arm 24. Piston Ring Sets Pin 25. 66/80cc Piston 26. Piston Retaining 27. Piston Pin 28. Crank Connector Clips Bearing BikeBerry.com 18003170479 39 ...
Page 41 2Stroke Cylinder Head Diagram 1. Spark Plug 2. Cylinder Body Cap 3. 66/80cc Top Head 4. Motor Head Stud Gasket 5. 66/80cc Cylinder Body 6. Intake Manifold 7. 66/80cc Bottom Head 8. Intake/ Exhaust Stud Gasket Gasket 9. Muffler Exhaust 10. Locking Nut 11. Washer 12. Lock Washer Gasket BikeBerry.com 18003170479 40 ...
Page 42 2Stroke Drivetrain Diagram 1. Sprocket Bolt 2. Sprocket Assembly 3. Sprocket Assembly 4. 9 Hole Sprocket Plate 1 of 2 Plate 2 of 2 Assembly Grommet 5. 9 Hole Sprocket 6. Nylon Lock Nut 7. Lock Washer 8. Washer Assembly Grommet 11. 44T Rear Sprocket 12. HD 415 Drive Chain 13. Chain Guard BikeBerry.com 18003170479 41 ...
Page 43 2Stroke Electrical Assembly Diagram 40. Magneto Case Cover 43. Magneto Case Cover 47. Magneto Loop Set 48. Magneto Washer Screw Gasket 50. Magneto Nut 51. Magneto 54. Clutch Case Cover 55. Clutch Case Cover Screw 56. CDI 57. Spark Plug Cap BikeBerry.com 18003170479 42 ...
Page 44 2Stroke Fuel Components Diagram 1. Gas Tank Cap 2. Gas Tank 3. Fuel Valve Pipe 4. Fuel Valve 6. Gas Tank Mounting 7. Washer 8. Nylon Lock Nut 9. CClip Bracket 10. Throttle Cable 11. Cable Adjustment 12. Carburetor Spring 13. Float Bowl Screw 14. Washer 15. EWasher 22. Jet Needle 25. Fuel Intake Nozzle 32. Intake Manifold 34. Air Filter Cap 35. Air Filter 43. Jet 44. NT Carburetor 45. Float Bowl Gasket 46. Float 50. Float Bowl BikeBerry.com 18003170479 43 ...

This manual is also suitable for:

Fh-bek80 Fh-mek80-b Fh-bek80-b Fh-bek48 Fh-mek48 Fh-bek48-b ... Show all