JL Audio RD500/1 Owner's Manual

JL Audio RD500/1 Owner's Manual

500w monoblock subwoofer amplifier

Advertisement

Quick Links

OWNER'S MANUAL
500W Monoblock Subwoofer Amplifier
Thank you for purchasing a JL Audio amplifier for
your automotive sound system.
Your amplifier has been designed and manufactured to exacting
standards in order to ensure years of musical enjoyment in your vehicle.
For maximum performance, we highly recommend that you have
your new amplifier installed by an authorized JL Audio dealer. Your
authorized dealer has the training, expertise and installation equipment
to ensure optimum performance from this product. Should you
decide to install the amplifier yourself, please take the time
to read this manual thoroughly to familiarize yourself
with its installation requirements and setup procedures.
If you have any questions regarding the instructions in this
manual or any aspect of your amplifier's operation, please contact your
authorized JL Audio dealer for assistance. If you need further assistance,
please call the JL Audio Technical Support Department
at (954) 443–1100 during business hours.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the RD500/1 and is the answer not in the manual?

Questions and answers

Summary of Contents for JL Audio RD500/1

  • Page 1 For maximum performance, we highly recommend that you have your new amplifier installed by an authorized JL Audio dealer. Your authorized dealer has the training, expertise and installation equipment to ensure optimum performance from this product.
  • Page 2: Protect Your Hearing

    (pg. 7) (pg. 8) (pg. 7) Turn On Mode Input Sensitivity Monoblock Subwoofer Amplifier Bass Boost (dB) LP Filter Freq. (Hz) CH. 1 MONO SUBWOOFER OUPUT CH. 2 +12 VDC Ground Remote 2 | JL Audio - RD500/1 Owner’s Manual...
  • Page 3: Planning Your Installation

    You should also take the time to Cooling Efficiency Considerations: securely mount the amplifier so that it does not The outer shell of your JL Audio amplifier come loose in the event of a collision or a sudden is designed to remove heat from the amplifier jolt to the vehicle.
  • Page 4: Product Description

    4 AWG copper wire, no longer than 36 inches and efficiency. (90 cm) from the amplifier to the ground The RD500/1 can be operated with a wide connection point. In some vehicles, it may be variety of source units and system configurations.
  • Page 5: Power Connections

    For optimal grounding, we recommend the use of a JL Audio ECS master ground lug (XB-MGLU). Alternatively, a sheet metal screw or bolt can be used with a star washer.
  • Page 6: Turn-On Options

    TURN-ON OPTIONS The RD500/1 can be switched on and off using without having to locate a remote turn-on lead at one of three methods, determined by the position the source unit, which can be very useful when of the amplifier’s “Turn-On Mode” switch. Please...
  • Page 7: Input Section

    RCA cables or plugs or use the JL Audio ECS Speaker Wire to RCA adaptor (XD-CLRAIC2-SW). Line output converters are usually not needed with the RD500/1.
  • Page 8: "Bass Boost" Control

    50 Hz and 500 Hz via the “LP Filter Freq. (Hz)” if the RBC-1 was not connected at all. In other words, it operates strictly as a level attenuator. control knob (80 Hz is a good starting point for tuning most systems). 8 | JL Audio - RD500/1 Owner’s Manual...
  • Page 9: Subwoofer Outputs

    PREOUTS SUBWOOFER OUTPUTS The RD500/1 incorporates a buffered, pass- The RD500/1 is designed to deliver power into through preamp output section, so that additional subwoofer loads equal to or greater than 2 ohms amplifiers can be easily added to the system.
  • Page 10: Status Led / Protection Circuitry

    The latter can result from a short circuit between the positive and negative speaker wires or between either speaker wire and the vehicle chassis. 10 | JL Audio - RD500/1 Owner’s Manual...
  • Page 11 If your amplifier fails or malfunctions, please return it to your authorized JL Audio dealer so that it may be sent in to JL Audio for service. There are no user serviceable parts or fuses inside the amplifier. The unique nature of the circuitry in the JL Audio amplifiers requires specifically trained service personnel.
  • Page 12 “Clipping” LED is solidly lit with the “Input Sensitivity” control turned all the way down, set the “Input Voltage” switch to the “High” position, then slowly increase the “Input Sensitivity” control until the “Clipping” LED is solidly lit. 12 | JL Audio - RD500/1 Owner’s Manual...
  • Page 13 APPENDIX B: RD500/1 Specifications Amplifier Section: Amplifier Topology: NexD™ High Speed Class D Power Supply: Unregulated MOSFET switching type Rated Power at 14.4V with less than 1% THD+Noise (20Hz - 20 kHz) RMS Method 250W RMS x 1 @ 4 ohms...
  • Page 14: Appendix C: Troubleshooting

    Check the input connectors to ensure that they all are making good contact with the input jacks on the amplifier. 14 | JL Audio - RD500/1 Owner’s Manual...
  • Page 15 “My amplifier shuts off once in a while, usually at higher volumes.” Check Check your voltage source and grounding point. The power supply of the RD500/1 will operate with charging system voltages down to 10V. Shutdown problems at higher volume levels can occur when the charging system voltage (or remote turn-on voltage) drops below 10V.
  • Page 16 Use this diagram to document your amplifier’s switch and control positions. Monoblock Subwoofer Amplifier CH. 1 ( L ) ( L ) CH. 2 ( R ) ( R ) +12 VDC Ground Remote 16 | JL Audio - RD500/1 Owner’s Manual...
  • Page 17 Turn On Mode Input Sensitivity Bass Boost (dB) LP Filter Freq. (Hz) MONO SUBWOOFER OUPUT...
  • Page 18 NOTES 18 | JL Audio - RD500/1 Owner’s Manual...
  • Page 19 NOTES...
  • Page 20 All warranty returns should be sent to JL AUDIO ’s Amplifier Service Facility freight-prepaid through an authorized JL AUDIO dealer and must be accompanied by proof of purchase (a copy of the original sales receipt). Direct returns from consumers or non-authorized dealers will be refused unless specifically authorized by JL AUDIO with a valid return authorization number.

Table of Contents