1. Introduction ALTO L12,L16,L20 FEATURES CHANNEL STRIPS. AUX send 1/2 switch-able to PRE/POST fader 60 mm high precision faders Each input channel with Mute, SOLO function, low cut filters-75Hz, 18 dB/OCT and Overload & signal present LEDs. Group “SUB” 1-2”, “SUB3-4”, or “main L-R” mix send switch-able 4 AUX sends with master control and SOLO function per channel: 2 ×...
2. Specification (L-12/16/20) 8. TECHNICAL SPECIFICATION Mono input channels Microphone input electronically balanced, discrete input configuration Frequency response 10Hz to 55kHz, + Distortion (THD & N) 0.005% at 4dBu, 1kHz Gain range 0dB to 60dB (MIC) SNR (Signal to Noise Ratio)
Page 5
Power supply Main voltage USA/Canada 100 120V~, 60Hz Europe 210 240V~, 50Hz U.K./Australia 240V~, 50Hz Power Consumption 70 watts Fuse 100 120V~ : T800mAL 210 240V~ : T500mAL Standard IEC receptacle Main connection...
RIGHT DFX OUT FX OUT L FX OUT R CTRL ROOM DSP BOARD LEVEL DFX SEND PRESETS VARIATIONS MUTE Titel ALTO MIXING CONSOLE DSP FOOTSWITCH Size Model No: Revision L-20 BLOCK DIAGRAM VER030125 Date: 1-Oct-2003 Sheet File: L20MAP.Sch Drawn By:...
7. Test Procedure Finished product test procedure 1. Instruments AP tester Double trace oscillometer Voltmeter 2. Functions test a. Input the proper AC power supply, turn on the main power, POWER LED will be illuminated (green). Then switch on PHANTOM power, PHANTOM LED will be illuminated (red), use a voltmeter to test the first pin and second pin of each MIC (MIC 1, MIC 2), the volt of phantom power should be 46V(±2V).
Page 44
LEVEL LEDs will turned off, when turn MAIN MIX LEVEL pot clockwise to the maximize, the LEVEL LEDs will be illuminated in sequence. test that whether the relating LED is illuminated when the level of output signal reaches the exactly value as LED shows .
Page 45
b. Turn EQ HI &LOW knob to the MAX and the MIN (EQ MID at the middle), test the frequency response, the frequency response curve is shown as follows, please refer to the following figure. Audio Precision 07/21/03 15:54:30 c. Turn EQ MID to the MAX and the MIN (EQ HI &LOW at the middle), test the frequency response, the frequency response curve is shown as follows, please refer to the following figure.
Page 46
Remarks: the frequency response test of normal instruments: a. Turn EQ LOW knob of the relating channel clockwise to the max (+15), the output is +15dBu(± 2dB), then turn EQ LOW knob of the relating channel counter-clockwise to the min. (-15), the output is –15dBu(± 2dB); Input the signal at 2.5kHz, Turn EQ MID knob of the relating channel clockwise to the max (+12), the output is +12dBu(±...
Page 75
No. Part No. Description Specification Remark 409 HC00233 IC socket (PCB) PLCC32 (D03-32T.A.4) 410 SG00016 SMD integrated circuit UDA1345TS (Philips) 411 AE00221 tin soldering paste SJ-617 412 NE11475 label 413 NH00035 bond paper 0.06*1M 414 NI00017 membrane 0.055*1M 415 AC00002 solder wire 63/37% C19,C12,C5,C2,C24,C16,C21,C25,C26,C28,...
Page 76
R1,R2,R3,R4,R5,R6,R7,R8 459 AE00221 tin soldering paste SJ-617 460 AC00002 solder wire 63/37% 461 MJ01235 side cover board L-12 left 462 MJ01236 side cover board L-20 left 1.0t*400*115 463 MJ00058 single light board 1*2135*1220 20.45kg 464 NE02717 label MADE IN CHINA 465 NH00038 paper 0.115*1M...
Page 77
No. Part No. Description Specification Remark 490 ND00282 EV foam 30*20*6 black 491 MI02287 barrier 0.3t*74*83.5*50.3_V1.1 492 MJ00087 iron board 0.3*200*3000 1.431kg 493 NA00279 clip-chain bag 0.04t*100*150mm_V1.0 494 AD00012 twin adhesive 90*120mm_V1.0 495 HA03865 row-stand connector wiring 2P-2P 305mm UL1007 28AWG...
Need help?
Do you have a question about the L-12 and is the answer not in the manual?
Questions and answers