Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Kamasa-TOOLS K 10253
Summary of Contents for Kamasa-TOOLS K 10253
- Page 1 Operating instructions Cordless K 10253 impact wrench...
-
Page 2: Operational Precautions
Operational precautions General safety instructions warning! Consider work area environment. Do not expose tools to rain. Do not use tools in damp or wet locations – Keep work area clean and well lit. Do not use tools in the present of flammable liquids or gases. -
Page 3: Product Safety Instructions
Product safety instructions warning! Disconnect battery pack from tool or place the main switch in the locked or off position before making any adjustments, changing accessories, or storing the tool. Such preventative safety measures reduce the risk of starting the tool accidentally. Remove adjusting keys or wrenches before turning the tool on. - Page 4 additional safety rules for charger & battery pack warning! Do not charge battery pack when temperature is below 10°C (50°F) or above 40°C (104°F). Do not attempt to use a set-up transformer, an engine generator or DC power receptacle. Do not allow anything to cover or clog the charger vents. Always cover the battery pack terminals with the battery pack cover when the battery pack: is not used.
-
Page 5: Specific Safety Rules And/Or Symbols
Watts d.c. Direct current Millimeter ft-lb Foot-Pound Newton meter Revolutions or Reciprocations per minute Model No. K 10253 Voltage 18.0V dc No load speed/min 0–1800 rpm Max tightening torque 540 Nm (400 ft-lb) Impacts per minute 2300 Tool weight (with battery) 2.9 kg (battery 0.720 kg) -
Page 6: Major Components
Major components Anvil Carbon brush panel Main switch Forward/Reverse knob Battery knob Fuel gauge label Battery pack accessory Charger Kamasa Tools is a trade mark of KG Knutsson AB, SE 191 81 Sollentuna, Sweden, Phone +46 8 92 30 00 www.kamasatools.com... -
Page 7: Operating Instructions
Operating instructions Installing or Removing Battery Pack (See Fig.1 Fig.2) Always switch off the machine before insertion or removal of the battery pack. To remove the battery pack, push the button on the battery pack and pull the tool unit from the battery pack in the direction.(See Fig.1.) Fig 1 To insert the battery pack, align the tool unit slides with the battery pack sliding groove and push the tool unit into place. - Page 8 LED indication Function The Battery Pack has a “SW” button and 4-step green LEDs for indicating remaining capacity status and Over temperature condition. The remaining capacity (RC) and temperature protection status green LED indications POWER INDICATION (3 seconds) when the “SW” button is momentarily pressed. Remaining Capacity LED Indication RC Status LED 1 (green)
-
Page 9: Tool Operation
Tool operation Installing Or Removing Socket Always be sure that the machine is switched off and the battery pack is removed before installing or removing the socket. Caution Fig. 1 To install the socket, push the socket into the driving spindle as far as it will go. - Page 10 Replacement of the carbon brush Replace the carbon brush while the motor is not rotated and the carbon brush is run out. (Replace the motor after the carbon brush has been replaced 2–3 times) Replacement procedure is as follows: Loose the carbon brush panel counterclockwise by using a screwdriver (Fig.1) Take out the carbon brush (Fig.2) Put the new carbon brush and carbon brush panel back into the housing in proper order (Fig.3) Lock the carbon brush panel back clockwise by using a screwdriver (Fig.
- Page 11 K 10253 Parts name Qt Spare part No Parts name Qt Spare part No Front cover ass’y Forward/reverse knob Rubber washer K 10269 Main switch K 10271 Washer Discharge protector Front impact ass’y K 10269 Battery connector Rear impact ass’y K 10269 Housing (L&R)
- Page 12 Kamasa Tools is a trade mark of KG Knutsson AB, SE 191 81 Sollentuna, Swe- den, Phone +46 8 92 30 00 www.kamasatools.com...
Need help?
Do you have a question about the K 10253 and is the answer not in the manual?
Questions and answers