Connecting With Soundbar; Compatible Models - Samsung SWA-8000S Owner's Manual
Wireless rear speaker kit
Hide thumbs
Also See for SWA-8000S:
- Manual (31 pages) ,
- Owner's manual (7 pages) ,
- User manual (128 pages)
Table of Contents
Advertisement
Available languages
Available languages
Connecting the SWA-8000S with Soundbar
c Before connecting to the Wireless Receiver Module, connect your subwoofer first.
c Use the speaker cable to connect the wireless receiver module to the speakers.
c Plug the Power cord into a power outlet. The LED turns on.
c If the Wireless Receiver Module is not linked to your Soundbar (displaying the LED indicator in Red), connect
them as follows.
1.
Check the Soundbar is in Power Off (Standby) status.
2.
Press the "Mute" button on your remote control for 5~6 seconds until the "ID SET" message appears on your
Soundbar display.
3.
Check the Wireless Receiver Module is in Standby status (displaying the LED indicator in Red).
4.
Press the ID SET button on the back with a sharp pin for 5~6 seconds until the LINK LED indicator on the
Wireless Receiver Module blinks (in Blue).
5.
Turn on your Soundbar with the "power" button on your remote control and wait for a while. They are completely
connected to each other if you can see the LINK LED indicator is continuously lit (in Blue).
c Once connected, your Soundbar and the Wireless Receiver Module are automatically reconnected even after
you turned them off and then on.
Compatible Models
HW-K360
HW-K369
HW-K390
HW-KM36
HW-KM36C
Wireless Models (including the frequency of 5.15GHz-5.35GHz)
• Hereby, Samsung Electronics, declares that this equipment is in compliance with the
essential requirements and other relevant provisions of Directive 1999/5/EC.
The original Declaration of Conformity may be found at http://www.samsung.com,
go to Support > Search Product Support and enter the model name.
This equipment may be operated in all EU countries.
This equipment may only be used indoors.
Wireless Models (excluding the frequency of 5.15GHz-5.35GHz)
• Hereby, Samsung Electronics, declares that this equipment is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC.
The original Declaration of Conformity may be found at http://www.samsung.com,
go to Support > Search Product Support and enter the model name.
This equipment may be operated in all EU countries.
HW-K450
HW-K550
HW-K460
HW-K551
HW-K490
HW-K560
HW-KM45
HW-K561
HW-KM45C
HW-K590
HW-J6000R
HW-JM4000
HW-J6001R
HW-JM4000C
HW-J6010R
HW-J6090R
HW-J6011R
HW-J4000
Hide quick links:
Advertisement
Table of Contents
Need help?
Do you have a question about the SWA-8000S and is the answer not in the manual?
Questions and answers
How to pair
To pair the Samsung SWA-8000S with your soundbar, follow these steps:
1. Connect the Cables:
- Plug the power cable into the Wireless Receiver Module.
- Plug the power cords of the Soundbar, Subwoofer, and Wireless Receiver into AC wall outlets.
2. Activate ID SET Mode:
- Press and hold the ID SET button on the back of the Wireless Receiver Module and Subwoofer for about 5 seconds.
- Keep holding until the STANDBY indicators turn off and the LINK indicators (Blue LEDs) blink quickly.
3. Enable ID SET on Soundbar:
- Ensure the Soundbar is powered off (STANDBY mode).
- Press and hold the Mute button on the Soundbar remote until ID SET appears on the Soundbar display.
4. Power On the Soundbar:
- Once the LINK indicator (Blue LED) on the SWA-8000S blinks, turn on the Soundbar.
5. Confirm Connection:
- When the LINK indicators (Blue LEDs) on the Subwoofer and SWA-8000S glow continuously, the setup is complete.
- This process may take a few minutes.
If the surround speaker volume is low, try pairing the devices again. If the issue persists, contact Samsung for assistance.
This answer is automatically generated