Summary of Contents for Gearmore GHF90
- Page 1 HAMMER KNIFE HEAVY DUTY SHREDDER Operation, Service, & Parts Manual For Models: GHF90, 100, & 140 March 2006 FORM: GHFMower.QXD...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Installation ........... .1 Safety Information . -
Page 3: Installation
INSTALLATION BEFORE ATTACHING THE SHREDDER TO THE TRACTOR Make sure that the shredder is suitable for your tractor's horsepower. YOUR TRACTOR's MODELS MAX. H.P. All Models with 540 RPM gearbox 100 HP All Models with 1000 RPM gearbox 120 HP CAUTION: Please note that if these limits are exceeded, it will invalidate your warranty. -
Page 4: Safety Information
SAFETY INFORMATION OPERATIONAL SAFETY: Disengage power to shredder and stop Guards and safety shields are for your engine before dismounting from tractor, protection. DO NOT operate equipment unless they are in place. before making any repairs or adjustments, transporting or unclogging shredder. Always operate tractor PTO (power-take-off) Take all possible precautions when leaving at recommended RPM (revolutions per... -
Page 5: Lubrication
LUBRICATION Grease all fittings according to the following schedule: 1. ROLLER (Ref. 1): Grease at both ends after 4 hours of operation, until grease is visible.. 2. CUTTING SHAFT (Ref. 2): Grease at both ends lightly after 8 hours of operation. DO NOT overgrease. -
Page 6: Pre-Operation Check List
PRE-OPERATION CHECK Check tightness of all bolts and nuts. Check gearbox oil level (Grade SAE80W-90 gear oil). Grease all points, on all GHF mowers. P.T.O. (power take-off) speed should not exceed shredder's rated RPM (revolutions per minute). Check correct length of P.T.O. shaft. When fitted, there should be 3 "... -
Page 7: Shredder Adjustments
SHREDDER ADJUSTMENTS FOR VARIOUS TYPES OF MOWING There is an adjustable rear hatch (Fig. 3) that can be set in one of seven positions to control the amount of power needed to do the work. FOR BEST MOWING OPERATION, OPEN REAR HATCH FULLY TO ALLOW MATERIAL TO EXIT Adjustment of the rear hatch can be made by removing the two bolts at the side (Fig. - Page 8 SHREDDER ADJUSTMENTS Various roller adjustments 3 positions Used for mulching of prunings Used for cutting grass Used to mulch cornstalk Page 6...
-
Page 9: Roller Height Control
ROLLER HEIGHT CONTROL The roller can be adjusted for 2 or 3 cutting heights. By raising the roller, you get a shorter cut, by lowering it, a longer cut is achieved. You can also fine adjust the cutting height with the top link arm. -
Page 10: Drive Belt Tension Adjustment
DRIVE BELT TENSION ADJUSTMENT 1. Check belt tension before each use (Fig. 8). The tension is correct when you can depress one belt 1 cm ( ") between the two pulleys. It is possible for you to insert a tool through the belt cover (Fig. -
Page 11: Troubleshooting
5. If you have any questions or problems, it is always best to contact your dealer immediately. 6. When ordering spare parts, you must contact your authorized Gearmore dealer for original replacement parts. When doing so, please include the following information:... -
Page 12: Deck Assembly
GHF DECK ASSEMBLY Page 10... -
Page 13: Deck Assembly
GHF DECK ASSEMBLY REF# QTY. PART NO. DESCRIPTION 14301033 Deck Frame GHF90 14301034 Deck Frame GHF100 14301035 Deck Frame GHF110 14301036 Deck Frame GHF120 13008021 Grass Hatch GHF90 13008022 Grass Hatch GHF100 13008023 Grass Hatch GHF110 13008024 Grass Hatch GHF120... -
Page 14: A-Frame Assembly
GHF A-FRAME ASSEMBLY Page 12... - Page 15 GRF A-FRAME ASSEMBLY REF# QTY. PART NO. DESCRIPTION 13004088 A-Frame 19704010 Support, P.T.O. 96689323 Bolt M6 x 25 96618421 Bolt M20 x 150 97096011 Washer 97972821 Lock Nut 14311003 Stand 14311001 Cap, Plastic 14311010 Pin w/Chain 97486611 Bolt M6.3 x 19 14311006 Support 19404015...
-
Page 16: Rotor Shaft Assembly
GHF ROTOR SHAFT ASSEMBLY Page 14... -
Page 17: Rotor Shaft Assembly
GHF ROTOR SHAFT ASSEMBLY REF# QTY. PART NO. DESCRIPTION 14302028 Complete Rotor GHF90 14302029 Complete Rotor GHF100 14302030 Complete Rotor GHF110 14302031 Complete Rotor GHF120 As Req'd 48020002 Hammer Knife As Req'd 13002076 Special Lock Nut M16 As Req'd 13002075 Bolt M16 x 1.8 x90... -
Page 18: Roller Assembly
GHF ROLLER ASSEMBLY REF# QTY. PART NO. DESCRIPTION 14305002 Complete Roller Assy. GHF90 14305003 Complete Roller Assy. GHF100 14305004 Complete Roller Assy. GHF110 14305005 Complete Roller Assy. GHF120 13005071 Roller Support 14305028 Bearing Hub Support UK209 Bearing 14305043 Nut H309... -
Page 19: Drive Assembly
GHF DRIVE ASSEMBLY REF# QTY. PART NO. DESCRIPTION 19703010 Gearbox Assy, 540 RPM (no ext. shaft) 19703009 Gearbox Assy, 1000 RPM (no ext. shaft) 19703017 Support Bracket 97095511 Washer 15 x 28 97095711 Washer 17 x 30 13003015 Pulley SPB250 13003006 Taper Lock 45 x 80 19603001... -
Page 20: Gearbox Assembly (540 Rpm)
GHF 540 RPM GEARBOX ASSEMBLY Page 18... - Page 21 Oil Seal 48030484 Pinion Shaft Z12 48030008 Spacer 40.3 x 51.5 30308 Bearing 30208 Bearing 40X80X10 Oil Seal 48030500 Extension Tube GHF90 48030501 Extension Tube GHF100 48030502 Extension Tube GHF110 48030503 Extension Tube GHF120 48030013 Bushing 48030363 48030511 Extension Shaft GHF90...
-
Page 22: Gearbox Assembly (1000 Rpm)
GHF 1000 RPM GEARBOX Page 20... - Page 23 96859001 Cotter Pin 48030485 Pinion Gear Z16 48030008 Spacer 40.3 x 51.5 30308 Bearing 30208 Bearing 40X80X10 Oil Seal Contact Gearmore 48030013 Coupler 48030363 Contact Gearmore 22209 Bearing 45X85X10 Oil Seal 96874976 Snap Ring 85 x 3 96693723 Bolt M12 x 25...
-
Page 24: Driveline Assembly
GHF PTO SHAFT Bondioli & Pavesi REF# QTY. PART NO. DESCRIPTION 572080351 RS Yoke 1-3/8 6 Spline 572083751 RS Yoke 1-3/8 21 Spline (Optional) 41208 #8 Cross Kit 204086860 Outer Tube Yoke 341054000 Roll Pin O.T. 225730860 Outer Drive Tube 225690860 Inner Drive Tube 204086861... -
Page 25: Driveline Assembly
GHF PTO SHAFT Weasler REF# QTY. PART NO. DESCRIPTION 110-8606 Yoke Auto Lock 400.724621 Yoke Auto Lock 201-6806 Cross and Bearing Kit 410.800245 Yoke Inner Tube 795.1290 Spring Pin 12 x 90 710.554 Inner Tube 710.634 Outer Tube 410.800263 Yoke Outer Tube 961-4589 Bearing Kit 902-4560... -
Page 26: Limited Warranty
Our obligation shall be limited to repairing or replacement of any part, provided that such part is returned within thirty (30) days from date of failure to Gearmore through the dealer from whom the purchase was made, transportation charges prepaid.
Need help?
Do you have a question about the GHF90 and is the answer not in the manual?
Questions and answers