Bosch GSC 10,8 V-LI Professional Original Instructions Manual page 11

OBJ_BUCH-840-005.book Page 11 Thursday, November 22, 2012 4:08 PM
Technical Data
Cordless Sheet Metal
Shears
Article number
Rated voltage
Stroke rate at no load n
0
Max. steel sheet cutting
capacity*
Smallest curve radius
Weight according to
EPTA-Procedure 01/2003
2
* to 400 N/mm with reference to steel sheet
Noise/Vibration Information
Measured sound values determined according to EN 60745.
Typically the A-weighted sound pressure level of the product
is less than 70 dB(A). Uncertainty K < 1.5 dB.
The noise level when working can exceed 80 dB(A).
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745:
2 2
a = 3.5 m/s , K< 1.5 m/s .
h
The vibration emission level given in this information sheet has
been measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with another.
It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained,
the vibration emission may differ. This may significantly in-
crease the exposure level over the total working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may signif-
icantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep hands warm, organise work patterns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with the fol-
lowing standards or standardization documents: EN 60745
according to the provisions of the directives 2011/65/EU,
2004/108/EC, 2006/42/EC.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
D-70745 Leinfelden-Echterdingen
Dr. Egbert Schneider Helmut Heinzelmann
Senior Vice President Head of Product Certification
Engineering PT/ETM9
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Leinfelden, 23.11.2012
Bosch Power Tools
Assembly
GSC 10,8 V-LI
Battery Charging
 Use only the battery chargers listed on the graphics
3 601 J26 1..
V= 10.8
-1
min 3600
Note: The battery is supplied partially charged. To ensure full
capacity of the battery, completely charge the battery in the
mm 1.3
battery charger before using your power tool for the first time.
mm 15
The Lithium-Ion battery can be charged at any time without
reducing its service life. Interrupting the charging procedure
does not damage the battery.
kg 1.4
The battery is equipped with a NTC temperature control
which allows charging only within a temperature range of be-
tween 0 °C and 45 °C. A long battery service life is achieved
in this manner.
Battery Charge-control Indication
The three green LEDs of the battery charge-control indicator
4 indicate the charge condition of the battery 2. For safety
reasons, it is only possible to check the status of the charge
condition when the machine is at a standstill.
– To indicate the charge condition, press and hold button 3
LED
Continuous lighting 3 x green
Continuous lighting 2 x green
Continuous lighting 1 x green
Flashing light 1 x green
Removing the battery
– To remove the battery 2, press the unlocking buttons 1 and
Operation
Starting Operation
Inserting the battery
 Use only original Bosch lithium ion batteries with the
Note: Use of batteries not suitable for the machine can lead to
malfunctions of or cause damage to the power tool.
– Insert the charged battery 2 into the handle until it can be
Switching On and Off
– To start the machine, push the On/Off switch 5 forward so
– To switch off the machine, push the On/Off switch 5 to-
The Lithium-Ion battery is protected against deep discharging
by the "Electronic Cell Protection (ECP)". When the battery is
page. Only these battery chargers are matched to the lith-
ium ion battery used in your machine.
of the switched off machine.
pull the battery out of the machine to the rear. Do not ex-
ert any force.
voltage listed on the nameplate of your power tool. Us-
ing other batteries can lead to injuries and pose a fire haz-
ard.
felt to engage and faces flush against the handle.
that the "I" is indicated on the switch.
ward the rear so that the "0" is indicated on the switch.
To save energy, only switch the power tool on when using it.
English | 11
Capacity
≥2/3
≥1/3
<1/3
Reserve
1 609 92A 007 | (22.11.12)