Advertisement
Quick Links
AUDIO MOUNT KIT
P/N 2880458
APPLICATION
2009-2015 SPORTSMAN XP MODELS, 2015 SPORTSMAN SP 570 AND 570 TOURING MODELS;
SPORTSMAN 570 AND SPORTSMAN 570 TOURING MODELS;
SPORTSMAN ACE MODELS;
RANGER AND RZR MODELS
BEFORE YOU BEGIN
Read these instructions thoroughly and make sure all parts and tools are accounted for. Please retain these
installation instructions for future reference and parts ordering information.
KIT CONTENTS
Ref
1
2
3
4
5
6
7
8
10
7
Qty
1
2
1
1
1
1
1
Audio Mount Bracket, SPH
1
P/N 9925685 Rev 01 09/14 Page 1 of 8
8
4
12
6
9
11
2
5
Part Description
Audio Cable
Plastic Clamp
Charger
Bluetooth Speaker
Audio Mount Bracket, XP
Audio Mount Base
Strap Audio Mount
1
3
Part Number
2412741
2878747
4015142
4015226
5260513
5260511
5260512
5415440
Advertisement
Summary of Contents for Polaris 2880458
- Page 1 AUDIO MOUNT KIT P/N 2880458 APPLICATION 2009-2015 SPORTSMAN XP MODELS, 2015 SPORTSMAN SP 570 AND 570 TOURING MODELS; SPORTSMAN 570 AND SPORTSMAN 570 TOURING MODELS; SPORTSMAN ACE MODELS; RANGER AND RZR MODELS BEFORE YOU BEGIN Read these instructions thoroughly and make sure all parts and tools are accounted for. Please retain these installation instructions for future reference and parts ordering information.
-
Page 2: Tools Needed
10-15 min IMPORTANT Your Polaris AUDIO MOUNT KIT is exclusively designed for your vehicle. Please read the installation instructions thoroughly before beginning. Installation is easier if the vehicle is clean and free of debris. For your safety, and to ensure a satisfactory installation, perform all installation steps correctly in the sequence shown. - Page 3 3. Align audio mount bracket (5) on the pod (B) and use as template to drill the holes (E) of dia 5/16” as shown in figure. 4. Fasten audio mount bracket (5) with audio mount base (6) using four screws (10) and nyloc nuts (11). Tighten screws until snug.
- Page 4 6. Align and Install audio mount assembly using two tuflok rivets (12) as shown in figure. 7. Use rubbing alcohol, pledge or other temporary lubricant on the rubber gasket, both sides. Push back bezel and cluster assembly (A) onto the pod as shown in figure.
- Page 5 3. If you cannot remove the cluster by hand, consider removing the upper pod (G) by removing three screws (H) as shown in figure. 4. Align audio mount bracket (7) with pod (G) and use as template to drill the holes of dia 5/16” as shown in figure.
- Page 6 6. Align and Install audio mount bracket assembly on the pod using two tuflok rivets (12) as shown in figure. 7. Use rubbing alcohol, pledge or other temporary lubricant on the rubber gasket, both sides. Push back bezel and cluster assembly (F) to fix onto the upper pod as shown in figure.
- Page 7 FOR SPORTSMAN ACE MODELS (1.75” TUBE MOUNT) 1. Fasten plastic clamp (2) with audio mount base (6) using four screws (10). Tighten screws until snug. 2. Snap fit bluetooth speaker (4) and strap (8) on to the audio mount assembly (K) as shown. 3.
- Page 8 FOR RANGER AND RZR MODELS (DASH MOUNT) 1. Place audio mount base (6) at required location on the passenger side dash panel and use as template to drill hole of dia 5/16” as shown in figure. NOTE: Ensure audio mount assembly installed on dash will not obstruct vehicle operation and driver’s vision.