Do you have a question about the LMXS30776S and is the answer not in the manual?
Questions and answers
Kathleen Woods
February 10, 2025
Freezer door was left open a little overnight and now the ice maker is not working. Temperature went up in freezer, stuff started to melt. Not sure if the 2 are related.
1 comments:
Mr. Anderson
February 11, 2025
The provided context does not specifically mention the LG LMXS30776S model or address whether the ice maker would stop working if the freezer door was left slightly open overnight. However, it does state that the ice maker may stop producing ice if the ice bin is full or if the ice becomes uneven. If the freezer door was left open, temperature fluctuations could affect ice production. Try closing the door properly, ensuring the ice bin is level, and allowing time for the ice maker to resume operation. If the issue persists, further troubleshooting may be needed.
SAFETY PRECATUTIONSS ..............................2 1. SPECIFICATIONS ................................3 2. PARTS IDENTIFICATION ..............................4 3. DISASSEMBLY................................5-29 REMOVING AND REPALCING REFRIGERATOR DOORS ....................5 DOOR ....................................6-7 SUB, PCB ....................................8 DOOR ALIGNMENT ................................9 FAN AND FAN MOTOR ..............................9-10 REFRIGERATOR LIGHT (TOP) ............................11-12 MULTI DUCT ..................................
2. PARTS IDENTIFICATION Adjustable Refrigerator Shelf LED interior lamps Door-In-Door Case Cheese & Butter Bin Indoor Ice Bin Condiment Bin Crisper EasyReach™ Custom Chill™ Drawer Pullout Drawer Durabase® and Durabase® Divider - 4 -...
4-1 COMPRESSOR 4-2-3 Compressor protection logic 4-1-1 Role 4-1-2 Notes for Usage 4-1-3 Remove the cover PTC (1) Remove the Cover Back M/C (2) Remove two screws on comp base (3) Use a L-shaped flap tooll to pry off the cover (4) Assembly in reverse order of disassembly - 30 -...
Ice Type When checking Resistance values, make sure to R efrigerator turn off the power, and wait for the voltage to Freezer discharge. Fresh Auto Air Filter Power F i l ter Reset Hold 3s ec Within 3 hours after the error : Press the Ice Plus button and Freezer button simultaneousl Ice Plus All errors, except for “E rt”, “E SS”, “E HS”, “E IS(except for Icing sensor)”.
Page 86
11-4 Door Switch, H Function How to <Switch, Refrigerator> Measure Button (Plunger) Beep Standard Multimeter beep – Switch,R - 86 -...
Page 87
11-5 Door Switch, F Function How to No magnet Magnet near the Switch Measure magnet Magnet must be center of Switch Magnet Center Magnet Center Switch Center Switch Center Bad position Good position Standard - 87 -...
Page 90
11-8 Damper Function How to Measure < Damper Circuit > Blue Blue White White Check the 3 Yellow < extension > Check the Check the Standard Damper - 90 -...
Page 91
11-9 Lamp Socket Function How to Measure Standard - 91 -...
Page 92
11-10 Flow Sensor Function How to Measure Standard - 92 -...
Page 96
12-2 Check B B1. LED blinks once, then repeats (FCT0 Fault) Protection Logi c Blink OFF Blink OF F - Purpose : Detecting motor current and voltage error - Check voltage at point A (Motor Voltage), point B (Motor Current) and Point C (Capacitor Voltage) when compressor is off.
Page 97
B3. LED blinks three times, then repeats (Stroke Trip) B4. LED blinks five times, then repeats (Locked Piston) B5. LED blinks six times, then repeats (Current Trip) - 97 -...
Page 98
B6. LED blinks seven times, then repeats n i l n i l n i l n i l n i l n i l n i l - Purpos e: P revent high current due to IPM S hort - Caus e: Damaged IPM (Dead Short) - Test for a dead short at P oint A with a V OM.
Page 102
LED operating condition Cause Service guideline LED two - time repetiton (Stroke Trip) - off - - off - - off repeating LED five - time repetiton (Piston Lock Trip) - off - - off repeating LED six - time repetiton (Current Trip) - off - - off repeating...
Page 103
12- 5 SERVICE DIAGNOSIS CHART COMPLAINT POINTS TO BE CHECKED REMEDY Warm position. Recommended position. Recommended position. colder position. Warm position. - 103 -...
Page 104
12- 6 REFRIGERATORION CYCLE Troubleshooting Chart TEMPERATURE STATE OF STATE OF THE OF THE CAUSE REMARKS THE UNIT EVAPORATOR COMPRESSOR 12-6-1 Cleaning - 104 -...
Page 105
12-6-2 SEALED SYSTEM DIAGNOSIS “Not Cooling” Complaint All components operating, No airflow problems, Not frosted up as a defrost problem problem has been isolated to sealed system area Frost Partial None Pattern? Equalization Equalization Test Test Very Fast Very Slow Very Slow Very Fast Fast...
Page 107
13-2 ICEMAKER FUNCTIONS 13-2-1Icemaking mode 13-2-2 Harvest mode 13-2-3 Fill/Park Position 13-3 Trouble Shooting Ice & Water System Issues 13-3-1 Icemaker not making ice or not making enough ice (Environmental Diagnosis) No making ice saddle valve. Water fill tube heater Is Icemaker’s tray filled all the water valve’...
Page 108
13-3-2 Icemaker not making ice or not making enough ice (Icemaker Unit & Ice-detecting sensor Diagnosis) - 108 -...
Page 109
STEP (Ice-detecting sensor Diagnosis) 2. Close the left door 1. Remove Ice bin from compartment 3. Wait for 3min. (Door switch pushed) 4. Freezer door stays open Ice Type Refrigerator 5. Push the refrigerator Freezer button & lock button at the same time.
14-1-1 Function 14-1-2 How to Toggle the Display between °D & °C 14-1-3 Lock function (dispenser and display button lock) - 110 -...
Page 111
14-1-4 Filter condition display function 14-1-5 Air Filter selection 14-1-6 Ice Plus selection 14-1-7 Dispenser Use selection - 111 -...
Page 112
14-1-8 CONTROL OF FREEZER FAN MOTOR 2. When refrigerator is overloaded, fan motor runs in high speed as powered-up Standard speeds is used for general purposes. 3. To improve cooling speed, the RPM of freezer fan motor changes from normal speed to high. 14-1-9 Cooling Fan Motor 14-1-10 Ice Compartment Fan 14-1-11 Refrigeration room Fan Motor...
Page 113
14-1-14 Defrosting (removing frost) For initial power on or for restoring power, defrosting starts when the compressor running time reaches 4 hours. 8-1-15. 14-1-15 Defect Diagnosis Function plus - 113 -...
REFRIGERATOR PARTS CAUTION: Use the part number to order part, not the position number. 141H 142C 141A 142A 142B 142D 141F 141B 141H 141H 141A 141A 141F 141F 141B 141B 255A 255B 154D 144A 177C 177E 132P 255A 162A 146E 141D 132S 161B...
Need help?
Do you have a question about the LMXS30776S and is the answer not in the manual?
Questions and answers
Freezer door was left open a little overnight and now the ice maker is not working. Temperature went up in freezer, stuff started to melt. Not sure if the 2 are related.
The provided context does not specifically mention the LG LMXS30776S model or address whether the ice maker would stop working if the freezer door was left slightly open overnight. However, it does state that the ice maker may stop producing ice if the ice bin is full or if the ice becomes uneven. If the freezer door was left open, temperature fluctuations could affect ice production. Try closing the door properly, ensuring the ice bin is level, and allowing time for the ice maker to resume operation. If the issue persists, further troubleshooting may be needed.
This answer is automatically generated