For each device to be commanded you must repeat this procedure. If you want to program X-Light 2 for a satellite device, digital terrestrial, follow the above procedure whereas paragraph 3 varies as follows:...
If the device responds correctly to the commands Press the device key of step 1:The code is learned and X-Light/X-Wire is ready. b) If the device does NOT respond correctly: start over from step 2 Note The complete automatic search could last several minutes (even 15-20 minutes);...
5. HOW TO READ BACK A MEMORIZED CODE If you have followed the automatic programming , once the search is over and the code is set, it is useful to know it and to write it down for future reference. Press the device key for the code belonging to the device that you want to read and keep it pressed for approximately 10 seconds.
Page 6
à l’arrière de la télécommande et insérez aux places prévues en respectant scrupuleusement la polarité. Lorsque les touches de sélection émettent 3 clignotements elles indiquent que la X-Light/X-Wire est prête à être programmée.. 2. NOUVELLE PROGRAMMATION PARMI L’ORDINATEUR (valable uniquement pour la version X Light) Ce système innovatif breveté...
Si l’appareil répond correctement aux commandes appuyez de nouveau sur la Touche de Sélection choisie au point 1: Le code est mémorisé et la X-Light/X-Wire est prête pour fonctionner. b) Si l’appareil N’Y répond PAS correctement répétez toute la procedure à...
Page 8
partir du point 2. Note La recherche automatique pourrait durer quelques minutes (même 15-20 minutes).Afin qu’elle soit efficace, il est important de garder la télécommande bien orienté vers l'appareil. Si vous avez accidentellement arrêté d’appuyer sur la touche l'appareil ne se soit éteint ou qu’une de ses fonctions ne se soit “...
Page 10
τις μπαταρίες στο πίσω μέρος και εισάγετε τις μπαταρίες, με μεγάλη προσοχή στην πολικότητα. Τα φωτεινά πλήκτρα Επιλογής θα εκπέμπουν 3 διαλείποντα φωτεινά σήματα ως ένδειξη ότι το X-Light / X-Wire είναι έτοιμο για προγραμματισμό. 2. ΝΕΟΣ ΠΡΟΓΡΑΜΜΑΤΙΣΜΟΣ ΜΕΣΩ ΥΠΟΛΟΓΙΣΤΗ (ισχύει μόνο για to X Light) Αυτό...
Page 11
του κωδικού που εντοπίσατε: Το πλήκτρο Selezione (Επιλογή) που επιλέξατε εκπέμπει 2 βραχεία διαλείποντα φωτεινά σήματα = OK. Το X-Light/X-Wire είναι έτοιμο για να διαχειρίζεται τη συσκευή σας. Σημείωση: Αν στο τέλος της διαδικασίας τα πλήκτρα επιλογής εκπέμπουν ένα παρατεταμένο φωτεινό σήμα, σημαίνει ότι σημειώθηκε ένα λάθος. Ελέγξτε αν εντοπίσατε...
Page 12
Σημείωση: Η αυτόματη αναζήτηση μπορεί να διαρκέσει μερικά λεπτά (μέχρι και 15-20 λεπτά). Για την καλή έκβαση της, είναι σημαντικό να κρατήσετε το τηλεχειριστήριο προσανατολισμένο προς τη συσκευή. Αν έχετε ελευθερώσει κατά λάθος το πλήκτρο “ ” πριν να σβήσει η συσκευή ή να ενεργοποιηθεί κάποια λειτουργία, μπορείτε να συνεχίσετε την...
Per ogni apparecchio da comandare occorre ripetere questa procedura. Se su X-Light 2 si vuole programmare per un apparecchio satellitare, digitale terrestre, Sky o altro seguire la procedura appena descritta considerando che il punto 3 varia come segue:...
Page 15
Se l’apparecchio risponde correttamente ai comandi premete di nuovo il Tasto di Selezione scelto al punto 1: Il codice è memorizzato e X-Light / X-Wire è pronto per funzionare. b) Se l’apparecchio NON risponde correttamente ripetete tutto dal punto 2.
Page 16
5. INDIVIDUALIZZAZIONE DEL CODICE MEMORIZZATO Se avete seguito la procedura di programmazione automatica, una volta terminata la ricerca, è utile conoscere il codice memorizzato ed annotarlo per eventuali impieghi futuri. Premete il tasto di Selezione del quale volete conoscere il codice e tenetelo premuto per circa 10 secondi.
Page 18
é necessário repetir o procedimento desde o começo. É necessário repetir este procedimento para cada aparelho. Se quiser programar o X-Light para um aparelho satelitar, digital terrestre, Sky ou outro, seguir o procedimento descrito acima considerando que o ponto 3 varia como segue: Pressionar contemporaneamente a tecla de Seleção DTT/SAT encima a direita...
Page 19
Se o aparelho responder corretamente aos comandos pressione novamente a Tecla de Seleção escolhida no ponto 1: O código foi memorizado e X-Light/X-Wire está pronto para funcionar. b) Se o aparelho NÃO responder corretamente, repita tudo desde o ponto 2.
Page 20
5. IDENTIFICAÇÃO DO CÓDIGO MEMORIZADO Se você tiver seguido o procedimento de programação automática, no final da pesquisa, será útil conhecer o código memorizado e anotá-lo para eventuais usos futuros. Pressione a tecla de Seleção do qual você quer conhecer o código e mantenha-o pressionado por cerca 10 segundos.
Need help?
Do you have a question about the X-LIGHT and is the answer not in the manual?
Questions and answers