Table of Contents
Advertisement
One-Star Alignment
It requires only one alignment star but, without accurate polar alignment and cone error calibration (see
Appendix A), it may produce lesser pointing accuracy than the other alignment methods. Refer to the
manual for information on how to perform accurate polar alignment. Below describes a step-
by-step procedure on how to perform the One-Star Alignment:
1. Make sure the telescope has been polar aligned.
2. In the alignment screen, select
3. The
will provide a list of stars available in your current sky for alignment. Using the
scroll keys, choose a star you are most familiar with and press ENTER. When the telescope
stops slewing, adjust its position with the directional keys until the star is centered on the
crosshairs in the finderscope. Now look through the eyepiece and adjust the telescope so that the
object is centred in the field of view of the eyepiece. Press ENTER to confirm.
4. Once completed,
Following is some pointers on how to choose appropriate alignment stars:
Star: Choose a star closer to the Celstrial Equator (smaller declination absolute value).
Two Star: Choose two stars that are on the same side of the meridian. and at least 3 hours apart in
and
apart in
two stars that are well more than 3" but less than
Three Star For the first two alignment stars, follow the same guideline as choosing for the
Alignment. For the third alignment star, choose a star that is on the opposite side of the
meridian of the first two stars. Both first alignment star and third alignment
have an absolute value of 30
the
of the third star should be at least
guideline when determining the correlation between the first and third stars in
Accuracy Enhancement (PAE)
three star alignment methods provide alignment adequate for any visual observing purpose. For
applications that require extra high precision in a particular part of the sky, the
Pointing Accuracy Enhancement (PAE) function to further improve the accuracy.
performed in up to 85 zones to cover the whole sky. The
should be already mapped out accurately by the
The following provides a step-by-step procedure on how to perform PAE:
1. Choose a star as reference object from a star chart or planetarium software. This star should be a
known, bright object that is currently located in the same part of the sky with the object of your interest.
2. Find the reference object in the
is under the control of the planetarium software, click on the object to slew to it.
3. Adjust the telescope so that the reference object is in the center of the eyepiece or CCD view.
4. Press and hold down the ESC key for
name of the reference object will appear in a blinking mode (3 times). If the go-to command is sent
from the
object".
5. Make sure that the reference object is still in the center of the view and press ENTER. If you do not
wish to record the result, press ESC to abort the operation. After pressing ENTER, the
will record the amount of pointing inaccuracy and recalculate the model of the sky. Now the pointing
accuracy of this particular part of the sky should be greatly improved.
The result for the star alignments and PAE is stored in the hand control even after the power has
been shut off. You will only need to perform the star alignment once as long as these two criteria
are met: 1 The telescope is moved to its home position (Park the telescope) before turning off the
power. 2. The telescope setup. including the mount, has not been moved. Accessory change is
acceptable as long as it is done with great caution. When
time. make sure that the time entered during initial setup is based on the same source as last time.
For example, if you enter the time on your watch during this observing session, the time you enter
next time should also be read from your watch.
using the scroll keys. Press ENTER to confirm.
will display "Alignment
If ou suspect that the polar alignment is off by l
70
hand control database and go-to the object. If the mount
2 seconds. The hand control will display "Re-center" and the
software, instead of the name of the object, the hand control will display "Last
o
and above, choose
apart in
If the first chosen star has a small
The following formula can be used as a
where the chosen alignment
Further accuracy enhancement is not necessary.
hand control is turned on for the
Star
should
provides a
PAE can be
is located
Hide quick links:
Advertisement
Table of Contents
