Kyosho Inferno MP777 Instruction Manual
  1. Manuals
  2. Brands
  3. Kyosho Manuals
  4. Toy
  5. INFERNO MP777
  6. Instruction manual
Kyosho Inferno MP777 Instruction Manual

Kyosho Inferno MP777 Instruction Manual

Hide thumbs Also See for Inferno MP777:
Table of Contents

Advertisement

Quick Links

Download this manual
Before beginning assembly, please read these instructions thoroughly.

INSTRUCTION MANUAL

INFERNO MP777
INDEX
RADIO PREPARATION
BEFORE YOU BEGIN
ASSEMBLY
OPERATING YOUR MODEL SAFELY
EXPLODED VIEW
© 2004 KYOSHO CORPORATION
REQUIRED FOR OPERATION
ARRANGEMENT OF PLASTIC PARTS ON RUNNERS
SPARE PARTS & OPTIONAL PARTS
*SPECIFICATIONS ARE SUBJECT TO BE CHANGED WITHOUT NOTICE.
UNDER SAFETY PRECAUTIONS
This radio control model is not a toy!
First-time builders should seek the advice of experienced modellers before
beginning assembly and if they do not fully understand any part of the
construction.
Assemble this kit only in places out of children's reach!
Take enough safety precautions prior to operating this model.
You are responsible for this model's assembly and safe operation!
Always keep this instruction manual ready at hand for quick
reference, even after completing the assembly.
R
THE FINEST RADIO CONTROL MODELS
2
3
3
4
5
6
7
8
28
29
30
32
33
36
No. 31777

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Inferno MP777 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Kyosho Inferno MP777

Summary of Contents for Kyosho Inferno MP777

  • Page 1: Instruction Manual

    You are responsible for this model's assembly and safe operation! Always keep this instruction manual ready at hand for quick reference, even after completing the assembly. *SPECIFICATIONS ARE SUBJECT TO BE CHANGED WITHOUT NOTICE. No. 31777 © 2004 KYOSHO CORPORATION...

  • Page 2: Required For Operation

    No.39516 (SG shaft only). Manifold (O.S.21RZ, Picco, Nova Rossi) Manifold (O.S.21RG) Required for engine starting: Paint Glow Fuel Fuel Pump Plug Heater For painting the body, use Kyosho paints for models! No.2230 No.73403 No.695145 No.96422 No.695142 POLYCA COLOR Spark Booster...

  • Page 3: Radio Preparation

    Phillips Screwdriver (L.M.S) Screw Cement Wire Cutters Sharp Hobby Knife Rubber Cement TOOLS INCLUDED Instant Glue Hex Wrench (1.5mm, 2mm, 2.5mm, 3mm) Box Wrench KYOSHO Special Glue No.96154 Grease No.1829 Grease No.695101 KNIFE EDGE REAMER ROUND CUTTER & SANDER Cross Wrench...

  • Page 4: Before You Begin

    Read through the manual before you begin, so you will have an overall idea of what to do. Check all parts. If you find any defective or missing parts, contact your local dealer or our Kyosho Distributor. How to read the instruction manual: No.4, No.5, No.6...
  • Page 5 BEFORE YOU BEGIN (2) This kit contains screws and hardware in different metric sizes and shapes. Before using them, check the screws on the true-to-scale diagrams on the left side in each assembly step. Some screws are extras. SCREWS OTHER HARDWARE Screw Self-tapping (TP) Screw Screw...
  • Page 6 ARRANGEMENT OF PLASTIC PARTS ON RUNNERS (1) No.1 Shaded parts are not used. No.4 Use the parts within the dotted lines as tunning options. Shaded parts are not used. No.5 Reverse Reverse...
  • Page 7 ARRANGEMENT OF PLASTIC PARTS ON RUNNERS (2) No.5 No.6 No.9 Shaded parts are not used. 159 160...
  • Page 8 No.2 Gear Differential (For front and rear) 4x4mm Flat surface (For center) 4 x 4mm 4 2.6 x 14mm Set Screw Shaft (Black) 5 6mm 7 8 x 16mm O-ring Ball Bearing For front and rear 10 4 x 10mm Shim For center No.2...

  • Page 9: Rear Gearbox

    No.2, No.4, Rear Gearbox No.5, No.10 4 x 20mm TP F/H Screw 4x20mm 4 x 25mm TP F/H Screw 13 x 16mm Thick Thin Shim 17 , 18 7 8 x 16mm Ball Bearing 4x25mm 17 , 18 Adjust the backlash with the shims.
  • Page 10 No.5, No.10 3x15mm Wing Stay Note the types of screws ! 4x15mm 3x15mm 3 x 15mm TP Screw 4 x 15mm 4 x 20mm 4x20mm TP Screw Screw 4x15mm 4x20mm Ò R Ó Ò R Ó marked. No.4, No.5 < >...
  • Page 11 No.5, Rear Suspension No.10 45 5 x 35mm Set Screw 14.5mm approx. 14.5mm 44 7.8mm 43 7.8mm Ball End Ball End No.4, No.10 Rear Suspension Nylon Nut 3x25mm 46 7.8mm Ball Note the direction. 3 x 25mm Cap Screw Holes for mounting. No.4, Rear Suspension No.10...

  • Page 12: Front Gearbox

    No.9, No.10 Chassis 4 x 20mm TP F/H Screw 4x20mm 4x20mm No.4, No.9, Chassis 3x18mm No.10 3 x 10mm F/H Screw 3 x 18mm Cap Screw Long Torque Rod Ball 55 6.8mm Ball End (L) 56 6.8mm Ball 3x10mm Front Gearbox No.6, No.10 4x20mm(F/H) 4 x 20mm...
  • Page 13 No.5, No.6, No.10 Front Gearbox 5 x 4mm Set Screw Tighten the set screw to the flat spot. 4 x 15mm 5x4mm TP F/H Screw 4 x 20mm TP F/H Screw 4x15mm ÒLÓ Use the "L" marked piece. 4x15mm Joint Cup (L) For now, no need to tighten screws firmly.
  • Page 14 No.5, No.6, No.10 Front Suspension For left side. For right side. 4x12mm E2.5 Left Note the direction. E2.5 4 x 12mm Right Set Screw Note the direction. 74 3 x 38mm E2.5 E Shaft E2.5 E-ring (Silver) Bottom For adjusting the ground clearance. 41 4 x 74mm E3 E Shaft...
  • Page 15 No.6 No.10 Front Suspension 3x10mm 3x15mm 3 x 3mm Set Screw 3x3mm 3 x 4mm Set Screw 3 x 10mm Set Screw 3x3mm 3 x 15mm Screw 2.6 x 5mm F/H Screw 5.8mm Ball 48 5.8mm 3x4mm Ball End (S) 2.5mm Diameter 2.5mm 2.6x5mm...
  • Page 16 Center Gearbox No.8 approx. 7mm Brake Caliper Brake Pad (Black) 12mm Center Differential Disk Plate Bolt (Long) Center Gearbox No.4, No.6, No.9, No.10 (Short) 4 x 15mm TP F/H Screw 3x8mm 3 x 8mm TP F/H Screw 3x8mm 4x15mm 3x3mm 13mm Center Gearbox 3x10mm...
  • Page 17 No.7, No.10 Steering 4x10mm Note the direction. 4 x 10mm F/H Screw Steering Collar Flanged Nut 104 6 x 10mm Ball Bearing 3x10mm 4x10mm 3 x 10mm Steering Pin 3x10mm Washer 3x10mm 4x10mm No.7, No.10 Steering Remove these screws and retighten after installing 3 x 10mm Long...
  • Page 18 No.3 Engine Engine Assemble the following parts with pulling the crankshaft. Engine taper collet included in the kit. Tapered Coret The short side of must be in the groove of Pilot Nut 115 3 x 5 x 0.2mm Shim No.3 Engine Engine 3 x 6mm...
  • Page 19 No.3, No.10 Engine Insert a sheet of paper before installing. Front 4 x 6mm 4x10mm F/H Screw 4x10mm 4 x 10mm Flanged Cap Screw 4x6mm 4x6mm No.9, No.10 Muffler 4 x 4mm Set Screw 3 x 6mm F/H Screw Manifold 4x4mm Muffler Bend so it fits into the muffler.
  • Page 20 3 x 15mm 3x15mm Fuel Tank TP Screw 3x15mm No.8, No.9, 3 x 10mm No.10 TP F/H Screw O-ring P3 Cut the Silicone Tube, depending on Engine and Muffler. 3x10mm Note the direction for O-ring. Note the types of screws ! 2x8mm 2x8mm 2x20mm...
  • Page 21 No.9, No.10 Radio Hook Pin Receiver Antenna Better to fill some sponge between radio box and receiver as well as battery. Battery No.10 Radio 3 x 12mm TP F/H Screw 3x12mm 3x12mm Part bags used. Must be purchased separately!
  • Page 22 No.9, No.10 Radio 3x12mm 3x12mm 3x10mm 3x15mm 3x10mm Steering Servo Throttle Servo (For transponder.) Note the types of screws ! 3 x 10mm 3 x 15mm Cords TP F/H Screw TP Screw 3 x 12mm 3 x 10mm Screw TP Screw Connect as per radio.

  • Page 23: Throttle Linkage Adjustment

    2.6mm Servo Horn Radio Note the directions of 2x6mm No.7, No.9, No.10 2.6x6x1mm Adjust the height with 2.6x6x1mm collar. 2.6x6x2mm 19mm With O.S. and NOVA Rossi engines : Adjust the height with 2.6x6x2mm collar. approx. 19mm 2.6x6x3mm Adjust the height with 2.6x6x3mm collar. With Picco engines : 3x3mm approx.
  • Page 24 Engine Rainy Weather No.3, No.10 After putting the cover on, loosen the screw, fit in the plastic washer and screw in the 3 x 10mm screw again. TP F/H Screw Soak inner sponge with oil. No.1948 Air Cleaner Oil 3x10mm 3x15mm 3x10mm Fuel Filter...
  • Page 25 Shock Oil Shock No.1 Fill in until shock oil nearly overflows. Check if piston moves smoothly. Then, gently move the piston up and down to get rid of air bubbles. Pull down the piston. ( ) — No.1 (Short) — For Front Shock ( ) —...
  • Page 26 Clean the tire rims with thinner beforehand. Wheels Apply instant glue little by little in the below order. Slide the tires into these slots in the wheels. Apply rubber cement and install in tires. No.4, No.6, No.10 Wheels < > <...
  • Page 27 After painting, remove the box for the color scheme. protective film from the body shell. Paint the body shell from the inside using Kyosho’s spray colors. Apply decals to any spots you like. Decals Cut off shaded portion. Drill holes with the specified diameter.
  • Page 28 No.10 Body Shell Wing Plastic Washer Slightly bend the body pins as shown in the diagram for easier removal. Body Pin MEMO Part bags used.
  • Page 29 OPERATING YOUR MODEL SAFELY WARNING: Do NOT operate the model in the following places and situations: (Non-observance may lead to accidents!) Always check the dry batteries in the radio! When the dry batteries get weaker, transmission and reception of the radio decrease. You may lose control of your model when operating it under such condition.

  • Page 31: Exploded View -1

    < > EXPLODED VIEW ( 1 ) Gear Differential IF102 IF39 IF39 ORG06 IF101 ORG06 IF102 BRG0120 BRG0120 IF102 IF103 IF106 BS107 < > IF102 < Front / Rear > IF101 IF102 IF39 IF39 ORG06 IF104 ORG06 IF102 BRG0120 IF102 BRG0120 IF103 BS107...

  • Page 32: Spare Parts

    SPARE PARTS FOR JAPANESE MARKET ONLY. Part Names Quantity Part Names Quantity BS45 Front Center Shaft 90 x 2 IF118 57 x 1 55 x 2 Rear Torque Rod Set 3x18mm 17 18 195 x 4 BS53 Shim Set 3x18mm Cap Screw 3x10mm BS79 Switch Boots 139 x 3...
  • Page 33 SPARE PARTS FOR JAPANESE MARKET ONLY. Part Names Quantity Part Names Quantity MP777 128 129 135 136 137 IF325 1050 W0141V 111 x 10 Receiver Box Set (MP777) 3mm Tapered Washer 140 146 170 3x6x2mm 92 138 x 2 145 147 x 4 x 10 W0142 3x6x2mm Collars...

  • Page 34: Optional Parts

    OPTIONAL PARTS FOR JAPANESE MARKET ONLY. Part Names Quantity Part Names Quantity BSW71 201 202 1050 IFW304 1890 Color Nylon Wing (Blue) instead of 201 202 SP Steering Plate instead of 201 202 BSW71 2625 IFW305 1050 instead of 201 202 SP Front Shock Stay instead of Color Nylon Wing (Fluorescent Green)
  • Page 35 Silicone Oil (500) Silicone Oil (2000) Silicone Oil (50000) for diffs. 3000 100000 SIL0550 SIL3000 SIL100000 Silicone Oil (550) Silicone Oil (3000) Silicone Oil (100000) THE FINEST RADIO CONTROL MODELS http://www.kyosho.co.jp/ 243-0034 046-229-4115 ) 10 00 18 00 PRINTED IN JAPAN 61920406-1...

Table of Contents