Page 1
Caseback markings Accurist Watches Logo Model Number MB 119 Calibre Number CAL 0T10 Battery Number SR927W...
Page 2
OS60, OS10 & OT10 Operating Instructions Dial A (minute dial) Top Left (TL) Top Right (TR) Dial C (hour dial) Position A Position B Position C Bottom Left (BL) Bottom Right (BR) Dial B (seconds dial)
Page 3
To set the time: 1. Gently pull out crown to position C. 2. Turn crown either way to correct time. 3. Push in crown to position A. To set the date: 1. Gently pull out crown to position B. 2. Turn crown anti-clockwise to adjust date. 3.
Page 4
OS60, OS10 & OT10 Operating Instructions continued . . . 3. Press BR Button to reset the chronograph 4. When you have finished with the Chronograph function, press BR Button again; this re-starts the small second hand on Dial B. Note: After 30 seconds the Second hand on Dial B will stop at the zero position, however, the time is still continuing to be measured in seconds and when TR Button is pressed to stop the timing, the second hands will automatically move...
Page 5
Chronograph zero set: This procedure is only necessary when the battery is replaced, or when the Chronograph hands do not return to the ‘0’ position, when the Chronograph mode is selected. 1. Gently pull out crown to position C. 2. Push TR Button to advance the sweep second hand to the 12 0’clock position. Please note each push of the TR Button will advance the hand 1 second.
Page 6
FS60 Operating Instructions Top Right (TR) Day indicator (The angle of this fanshaped day indicator may vary from model to model). Chronograph Minute Hand Position A Position B Position C Bottom Right (BR) Chronograph Second Hand Date indicator...
Page 7
To set the time: 1. Gently pull out crown to position C. 2. Turn crown either way to correct time. 3. Push in crown to position A. To set the date: 1. Gently pull out crown to position B. 2. Turn crown anti-clockwise to adjust date. 3.
Page 8
FS60 Operating Instructions continued . . . To set the day: 1. Gently pull out the crown to position B. 2. Turn the crown anti-clockwise to adjust day. 3. Push in crown to position A Note: If the date is set between the hours of around 11.00pm and 2.00am, the date may not change on the following day.
Page 9
Using the chronograph: 1. Press TR Button to start and stop chronograph. 2. Press BR Button to reset the chronograph. (the second and minute hands will return to the 12 o’clock (0) position) Chronograph zero set: This procedure is only necessary when the battery is replaced, or when the Chronograph hands do not return to the 12 o’clock (0) position.
Page 10
Cal OS20 Operating Instructions Top Right (TR) Chronograph minute counterhand Position A Position B Position C Small second dial Bottom Right (BR) 24 hour dial...
Page 11
For timing events up to 1 hour 1. To start chronograph press button TR. 2. To stop chronograph press button TR 3. To return hand to zero position press button BR Troubleshooting - If your watch receives a knock and the second hand is not on zero: 1.
Care of your watch Avoid temperature extremes 1. Avoid leaving your watch in direct sunlight or in extremely warm conditions for long periods of time: this will cause malfunctioning and shorten the life of the battery. 2. Do not leave your watch for long periods of time in extremely cold places; this may cause your watch to gain or lose time.
Page 13
Avoid strong shocks 1. This watch will withstand the bumps and jars normally incurred during sports activities. 2. Avoid dropping your watch on the ground or otherwise imparting severe shock to it. Avoid strong magnetic fields 1. Keep your watch away from strong magnets 2.
Page 14
Periodic inspection 1. A regular 4 to 5 years service by an authorised Accurist technician will ensure trouble free operation. 2. Refer to the After Sales Service section on page 32 for details.
Page 15
IMPORTANT 1. Keep the batteries out of reach of infants and small children. Should accidental ingestion occur consult a doctor immediately. 2. Do not attempt to replace the battery yourself as this invalidates your guarantee. Keep your watch clean Wipe off any moisture that adheres to the case, glass or band with a soft, clean cloth.
Bracelet Adjustment The bracelet requires a small adjustment and the model has a Z-type clasp. 1. Depress the end of the spring bar on the centre clasp with a pin. 2. Relocate the spring bar in an alternative hole.
Page 17
The bracelet requires a significant adjustment or the model does not have a Z-type clasp. 1. Use the enclosed wrist gauge to measure and mark the size of your wrist. 2. Return the completed wrist gauge with your watch...
Resistance to water INDICATIONS ON DIAL OR CASEBACK LIGHT SPRAY, DIAL CASEBACK PERSPIRATION, SWIMMING LIGHT RAIN ETC... BATHING, ETC... WATER RESISTANT WATER RESISTANT WATER RESISTANT 50M (5 ATM) WATER RESISTANT WATER RESISTANT 100M (10 ATM) WATER RESISTANT WATER RESISTANT 150M (15 ATM) AND DEEPER...
Page 19
DIVING: SKIN DIVING: SCUBA DIVING: WHEN USING A DIVING WITHOUT DIVING WITH HELIUM ENRICHED AN AIR TANK AN AIR TANK ENVIRONMENT...
Page 20
Resistance to water continued . . . IMPORTANT - NEVER PULL OUT THE CROWN WHEN THE WATCH IS WET. • Tighten screwlock crown completely • Water resistance is not a permenant property. We strongly recommend you return your watch for resealing every 4 - 5 years and/or when changing batteries •...
Need help?
Do you have a question about the MB 119 and is the answer not in the manual?
Questions and answers