PIONEER Service Manual. A subscription to, or additional copies of, Also test with plug reversed Earth PIONEER Service Manual may be obtained at a nominal (Using AC adapter ground charge from PIONEER. plug as required)
Page 3
The backlighting lamp of LCD in this equipment contains mercury. Disposal of this material may be regulated due to environmental considerations according to Local, State or Federal Laws. For disposal or recycling information, please contact your local authorities or the Electronics Industries Alliance: www.eiae.org L 13942296513 u163 SC-09TX http://www.xiaoyu163.com...
Page 4
To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be installed before shipment. Please be sure to follow this method especially if it is specified in this manual. SC-09TX http://www.xiaoyu163.com...
Compared with eutectic solders, lead-free solders have higher bond strengths but slower wetting times and higher melting temperatures (hard to melt/easy to harden). The following lead-free solders are available as service parts: • Parts numbers of lead-free solder: GYP1006 1.0 in dia. GYP1007 0.6 in dia. GYP1008 0.3 in dia. L 13942296513 u163 SC-09TX http://www.xiaoyu163.com...
Disturbed image (video jumpiness) Volume too high Too dark Volume fluctuating Too bright Sound interrupted Mottled color Cleaning the Fan Before shipment, be sure to clean the fan, using the following cleaning materials: Cleaning paper : GED-008 u163 SC-09TX http://www.xiaoyu163.com...
2P Extension cable GGD1550 These are used for a diagnosis of Power amplifier Section and product inside. 24P FFC GGD1551 7P Extension cable GGD1552 4P + 3P Extension cable GGD1553 12P + 3P Extension cable GGD1554 L 13942296513 u163 SC-09TX http://www.xiaoyu163.com...
2.0mm CABLE HOLDER (*;1.5mm CABLE HOLDER) mark found on some component parts indicates the importance of the safety factor of 2.0mm WIRE TRAP the part. Therefore, when replacing, be sure to use parts of identical designation. B*B-PH-K-S PH CONNECTOR SC-09TX http://www.xiaoyu163.com...
Page 25
<POWER AMP> FRONT CENTER 1/2 CENTER SW 1/2 SURROUND A SURROUND L/R SURROUND B SURROUND BACK L/R SURROUND BACK EXT. L/R FRONT L/R CENTER 1/2 ZONE2 SW 1/2 SURROUND L/R SURROUND BACK L/R u163 EXT. L/R ZONE3 ZONE2 ZONE3 SC-09TX http://www.xiaoyu163.com...
Hard serial line for microcomputer 232C Microcomputer which is controlled by rewriting Soft serial serial communication Other controls u163 The main circuit block Interruption block Switch Principal which is controlled by related to power ON memories other communication SC-09TX http://www.xiaoyu163.com...
1 Input a PCM signal (signal from a CD, etc.). Failure in the DIR 2 Set the listening mode to Pure Direct (PCM Direct). 3 Set the signal switch to Auto or PCM. u163 Failure in the D/A Failure in the DSP SC-09TX http://www.xiaoyu163.com...
Page 35
Check the video output signal from the HDMI input/output. u163 Failure in the buffer Failure in the HDMI TX between TX and scaler SC-09TX http://www.xiaoyu163.com...
Page 36
MONITOR output and on the LCD display? Only on the monitor screen Only on the LCD display Neither Failure in the LCD_SW (HDMI), Failure in the video Failure in the buffer (Composite), or LCD module converter block OSD block L 13942296513 u163 SC-09TX http://www.xiaoyu163.com...
Page 37
• Can the unit be turned on using a remote control unit connected via the SR IN connector? Failure in the EVENT Poor connection in microcomputer or the the front block IR 232C Assy u163 SC-09TX http://www.xiaoyu163.com...
Page 38
(main) microcomputer (For details on the Assys other Assy on which microcomputers are mounted, see the block u163 diagram.) * If the version of the AUDIO (DSP) microcomputer is not displayed, check also the connection between the DSP Assy and the MAIN DIGITAL Assy. SC-09TX http://www.xiaoyu163.com...
Possible causes: u163 Failure in the V-AUDIO Failure in the MULTI CH Assy, A-AUDIO Assy, or IN Assy, MOTHER1 Assy, the Assy being connected, or the Assy being or poor connection of connected, or poor connectors connection of connectors SC-09TX http://www.xiaoyu163.com...
Page 40
L 13942296513 Assy, or the Assy being Assy, or the Assy being Assy, A-AUDIO Assy, or connected, or poor connected, or poor the Assy being connected, connection of connectors connection of connectors or poor connection of connectors u163 SC-09TX http://www.xiaoyu163.com...
Page 41
Is ±15-V power output from the OP amp, which is or the power-supply block connected located at the stage after the DAC? to that regulator u163 Failure in the DAC or Poor connection of connectors its peripheral circuits on the path of power supply SC-09TX http://www.xiaoyu163.com...
Page 42
VIDEO CONVERT is set to ON, is the video Assy suspected signal output from an FFC cable connected to the HDMI connector of this unit? Failure in the COMPOSITE Assy or Failure in the HDMI Assy or the FFC cable S-VIDEO Assy suspected suspected u163 SC-09TX http://www.xiaoyu163.com...
Page 43
FFC cable connected to the HDMI connector of this unit? u163 Failure in the Failure in the Failure in the Failure in the COMPONENT Assy HDMI Assy A-REG Assy COMPONENT Assy or the FFC cable suspected suspected suspected suspected SC-09TX http://www.xiaoyu163.com...
Page 44
Use of a digital oscilloscope is recommended for checking. Failure in the Poor connection in the periphery u163 of the main (system) micro- EVENT microcomputer computer or defective unit (Possible defective parts: IR 232C, MOTHER 2, MOTHER 1, and board connectors) SC-09TX http://www.xiaoyu163.com...
Page 45
Failure in the DISPLAY block of the front LCD8V power microcomputer or a panel supply block of the front panel Failure in the Assy that cannot be controlled or poor connection between the uncontrollable Assy and other Assy u163 SC-09TX http://www.xiaoyu163.com...
Page 46
ICE INPUT 6CH Assy. power supply. SMPS Assy * How to confirm that the speaker relay is activated: Check if sound of relay operation is heard when the SP Relay ON/OFF key on the front panel is pressed. SC-09TX http://www.xiaoyu163.com...
PROTECT screen (2) Accumulate time EX.SSP DOWNLOAD screen EVENT DOWNLOAD Display DOWNLOAD New ITEM DOWNLOAD DSP u-com DOWNLOAD HDMI DOWNLOAD 1st DSP Firm DOWNLOAD u163 3rd DSP Firm DOWNLOAD screen Return to VERSION SC-09TX http://www.xiaoyu163.com...
Page 48
Detection of abnormality in the fans for HDMI i.Link − Number of HDMI OVER (abnormal voltage) detections Detection of over-voltage in the HDMI MCACC Clear the numbers of detections mentioned above. − − − This is to be used before shipment or after repair. SC-09TX http://www.xiaoyu163.com...
Page 49
[k] [l] [ENTER] Service mode continuation L 13942296513 Setting of the Timer of Exception "Set Stream The Timer of Exception Path" command on CEC "Set Stream Path" Key Operation [k] [l] To DOWNLOAD Service mode screen continuation u163 SC-09TX http://www.xiaoyu163.com...
ON or OFF. the function for FAN ON/OFF which the test code While the fans are on, they operate has been registered. at high speed. The fan for HDMI is not turned on or off but continues to operate. u163 SC-09TX http://www.xiaoyu163.com...
T y p e 1 ] i P o d m o d e T y p e 1 ] [ENTER] L 13942296513 [ENTER] To Normal mode Via the Power On routine (Power ON sequence mode) u163 SC-09TX http://www.xiaoyu163.com...
HDMI in the HDMI system power off. system. When an abnormality of over- Abnormality detection LED flashes after the MCACC LED voltage is detected in the in the HDMI system power off. power supply for HDMI system. u163 SC-09TX http://www.xiaoyu163.com...
Page 55
When the power is turned on again, perform the following "How to Enter Release Mode". [How to Enter Release Mode] During Standby mode, simultaneously press and hold the " j (DOWN)" and "ZONE2 ON/OFF" keys for 2 seconds. u163 SC-09TX http://www.xiaoyu163.com...
Page 56
DSP NG : There is no response from the DSP microcomputer. HDMI NG : There is no response from the HDMI microcomputer. NEW ITEM NG : There is no response from the NEW ITEM microcomputer. u163 SC-09TX http://www.xiaoyu163.com...
Page 57
MODEL ID ERROR : The model ID stored in the flash memory on the host board and that stored in this unit are different. CONFIG ERROR : This error is generated when the unit is turned off while the Config ROM data are being written to the flash memory. u163 SC-09TX http://www.xiaoyu163.com...
7. DISASSEMBLY 3 7 63 1515 0 The screws which is used in rear part (reference information) L 13942296513 ABA7078 CBZ30P080FTB PCZ26P060FTB PMZ30P060FTB VPZ30P100FTB BBT30P060FTB u163 SC-09TX http://www.xiaoyu163.com...
Page 59
Exterior Section Top plate B Remove the three screws. Remove the seven hex. screws (+ washer). Remove the top plate B. Rear view L 13942296513 Top plate B Side panel BU and BL Remove the four screws. u163 SC-09TX http://www.xiaoyu163.com...
Page 60
L 13942296513 Side Panel BL Side Panel BL P. metal B Side L Side R Remove the 12 screws. Remove the two screws (+ washer). Remove the two P. metals B. P. metal B P. metal B u163 SC-09TX http://www.xiaoyu163.com...
Page 61
HDMI Assy ×4 Beam L HDMI shield Assy and beam L Remove the seven screws. Remove the beam L. Remove the two screws. Remove the six screws. Remove the HDMI shield Assy. HDMI shield Assy u163 Rear view SC-09TX http://www.xiaoyu163.com...
Page 62
Reconnect the connector. Shield sheet A Side angle Remove the two screws. Remove the one screw. L 13942296513 Side angle Side angle Side L Side R Remove the 20 screws. Remove the two side angles. u163 ×6 ×6 SC-09TX http://www.xiaoyu163.com...
Page 64
Remove the shield sheet B. Beam S Shield sheet B Beam S Heatsink REG A-REG Assy A-REG Assy Remove the two screws. L 13942296513 Disconnect the seven connectors. Remove the A-REG Assy with heatsink REG. ×6 COMPOSITE Assy Exchange of PCB u163 SC-09TX http://www.xiaoyu163.com...
Page 65
PERCH DISP Assy Disconnect the one flexible cable. Remove the PERCH DISP Assy. L 13942296513 MAIN DIGITAL Assy Disconnect the four connectors. Remove the front section. Exchange of PCB u163 Front section FRONT BUFF Assy FRONT USB Assy SC-09TX http://www.xiaoyu163.com...
Page 66
Disconnect the one flexible cable and five connectors. IR 232C Assy PRIMARY Assy ICE REG Assy DAC Assy Release the three jumper wires. ICE INTERFACE Assy Side L Side R L 13942296513 Remove the five screws. Panel stay Remove the three screws. u163 Rear view SC-09TX http://www.xiaoyu163.com...
Page 67
Also be aware of the hazard of electric shock when working ∗ u163 on the SMPS section, as the primary power circuit (high voltage) resides in this section. ICEPOWER SMPS Assy SC-09TX http://www.xiaoyu163.com...
Note that confirmation with audio check or version check is insufficient for checking if updating has been completed. If you set the unit to STANDBY OFF without confirming of "OK" indication on the FL display, be sure to perform the updating procedures again. u163 SC-09TX http://www.xiaoyu163.com...
Page 70
(1) Check the version by pressing and holding the ENTER key and ZONE 2 (MULTI-ZONE CONTROL) key simultaneously for several seconds. (2) Check the downloaded version with the LCD screen. DSP1 : ∗.∗∗∗ DSP3 : ∗.∗∗∗ (3) For confirmation, check basic operations. u163 SC-09TX http://www.xiaoyu163.com...
Page 71
"OK" is not displayed. If an error is generated because any scratches on the disc, "OK" is not displayed. → In such a case, play back the same stream stored on another track as backup. L 13942296513 u163 SC-09TX http://www.xiaoyu163.com...
9. Select the communication speed. u163 • Base speed: 19200 • Data Send Speed: 57600 10. Click on "START" button. 11. "Completed" is displayed in the"ufu.exe" window. Select the communication speed. • Base Speed: 19200 • Data Send Speed: 57600 SC-09TX http://www.xiaoyu163.com...
Therefore, do not connect the iPod until this indication is displayed. L 13942296513 4. Connect the iPod. The name of the file for updating is always "Player.rom." 5. Counting continues until updating is completed. 6. Updating is completed. Turn the power OFF. u163 SC-09TX http://www.xiaoyu163.com...
Page 74
7. Check to make sure that the version has been updated. Press and hold the [i] and [POWER] keys for about 5 sec. 8. After about 20 sec., the updated firmware version is automatically displayed. L 13942296513 u163 SC-09TX http://www.xiaoyu163.com...
Screws adjacent to b mark on product are used for disassembly. For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions, apply as you think it appropriate.) 9.1 PACKING SECTION L 13942296513 u163 SC-09TX http://www.xiaoyu163.com...
Page 77
AHA7461 16 Spacer TER AHB7143 17 Accessory Box TER AHB7153 18 Packing Case TER AHD8506 19 Packing Sheet TER AHG7133 20 Packing Sheet TER NF AHG7136 21 Handle Cover AHX7034 22 iPod Caution Card ARM7111 L 13942296513 u163 SC-09TX http://www.xiaoyu163.com...
9.2 EXTERIOR SECTION 3 7 63 1515 0 Part of Panel base L BKU L 13942296513 u163 Refer to “9.4 MAIN CHASSIS SECTION (1/2)”, “9.5 MAIN CHASSIS SECTION (2/2)”. Refer to “9.3 FRONT SECTION”. SC-09TX http://www.xiaoyu163.com...
Page 79
22 Washer WH30FTC 23 Screw BBT30P060FTB L 13942296513 24 Screw FBN 4 x 10 ABA7143 25 Washer WA42D080D050 26 Gasket (6 x 6 x 25) ANK7141 > 27 Ferrite Core (L1949) ATX7010 28 Caution Label TER KU ARW7371 u163 SC-09TX http://www.xiaoyu163.com...
3 7 63 1515 0 ∗ F. Panel Assy BKU U PERCH DISP ∗ 5081 PERCH FFC Part of CN5091 F. Panel Assy BKU U (AZW7304) ∗ L 13942296513 V-AUDIO ∗ CN3108 MOTHER 2 CN8514 HN MODULE CN7801 MAIN DIGITAL CN307 u163 SC-09TX http://www.xiaoyu163.com...
NEW ITEM CN7007 L 13942296513 COMPOSITE CN2005 AUDIO BRIDGE 1 NEW ITEM J3411 CN7008 T1501 DAC CN1052 MAIN DIGITAL CN973 T1501 Part of u163 Panel base L BKU Refer to “9.6 REAR SECTION (1/2)”, “9.7 REAR SECTION (2/2)”. SC-09TX http://www.xiaoyu163.com...
Need help?
Do you have a question about the SC-09TX and is the answer not in the manual?
Questions and answers