For additional information or to speak to a representative, through openings, as they may touch dangerous voltage points or short out please contact the Philips Communication, Security & Imaging parts that could result in a fire or electric shock. Never spill liquid of any location nearest you: kind on the unit.
SAFETY PRECAUTIONS SECURITE ATTENTION RISQUE D’ÉLECTROCUTION. NE PAS OUVRIR ! CAUTION: TO REDUCE THE RISK OF DANGER : POUR ÉVITER TOUT RISQUE ELECTRICAL SHOCK, DO NOT OPEN D’ÉLECTROCUTION, VEUILLEZ NE PAS COVERS. NO USER SERVICEABLE PARTS OUVRIR LE BOÎTIER. IL N’Y A PAS DE INSIDE.
Page 5
SICHERHEITSHINWEISE SEGURIDAD VORSICHT PRECAUCIÓN ELEKTRISCHE SPANNUNG. RIESGO DE DESCARGA ELÉCTRICA NICHT ÖFFNEN! ¡NO ABRIR! PRECAUCIÓN: PARA REDUCIR EL RIESGO VORSICHT: DAS GEHÄUSE ZUR DE DESCARGA ELÉCTRICA, NO ABRA LAS VERMEIDUNG VON ELEKTRISCHEN TAPAS. EN EL INTERIOR NO HAY NINGÚN SCHLÄGEN NICHT ÖFFNEN. DAS GERÄT COMPONENTE REPARABLE POR EL USUARIO.
Page 6
VEILIGHEIDSMAATREGELEN SICUREZZA VOORZICHTIG ATTENZIONE GEVAAR VOOR ELEKTRISCHE SCHOK. PERICOLO DI SCOSSA ELETTRICA. NIET OPENEN! NON APRIRE. VOORZICHTIG: MAAK HET APPARAAT NIET ATTENZIONE: PER RIDURRE IL PERICOLO DI OPEN OM DE KANS OP ELEKTRISCHE SCOSSA ELETTRICA, NON APRIRE LE SCHOKKEN TE VERMIJDEN. BEVAT GEEN COPERTURE.
LTC 2372 & LTC 2375 Operation ... .16 the nearest Philips Communication, Security & Imaging Service LTC 2376 & LTC 2377 Operation ... .16 Center for authorization to return and for shipping instructions.
Page 8
PHILIPS PHILIPS PHILIPS PHILIPS PHILIPS MADE IN KOREA CLASS II VIDEO IN Figure 1 Typical Configuration for LTC 2372 & LTC 2375 VidQuad Digital Processor Unit PHILIPS PHILIPS PHILIPS PHILIPS PHILIPS ALARM / REMOTE MADE IN KOREA CLASS II Auto-terminating...
INSTALLATION LTC 2372 and LTC 2375 Connection MADE IN KOREA CLASS II VIDEO IN Figure 3 LTC 2372 & LTC 2375 Connection Video Inputs/Outputs: Camera 1 Video Input 1 - BNC Camera 2 Video Input 2 - BNC Camera 3 Video Input 3 - BNC Camera 4 Video Input 4 - BNC...
Grounding Connection If the unit is not rack-mounted, a separate grounding wire may be required to eliminate the effects of image interference. Attach a wire compliant with local codes between the grounding screw on the rear panel and a suitable earth ground. PROGRAMMING LTC 2372 &...
Time and Date 5.3.3 Time/Date Set This menu allows you to set the date and time format, the • Select TIME/DATE SET and press the key. The current time/date, and the displayed position on the monitor. following menu is displayed: •...
5.5.2 Alarm Dwell Time • Press the key to increase the dwell time. Dwell times The ALARM DWELL function allows you to set the automatic may be programmed from SKIP to 9 seconds (when you reset period after an alarm is generated. reach 9 seconds, pressing the key will toggle you through the sequence again).
5.5.4 Video Loss Alert VCR Out Mode (LTC 2377 only) The VIDEO LOSS ALERT function enables you to define if The VCR OUT MODE defines how the unit’s video output to an alarm is generated when any of the video inputs is the VCR or a DVR is recorded, either as quad mode, or as the lost/defective.
• Select COLOR ADJUST and press the key. The CAMERA 1 TITLE SET following menu is displayed: CAMERA 1 BRIGHTNESS CAMERA 1 ..TO EXIT PRESS ENTER KEY ..• Press the < > keys to move the cursor to the required position.
Set the Password 5.9.1 Disable Password The unit incorporates a password function for entry to the The password function can be disabled. menu operation. This ensures that only authorized persons can • Select DISABLE PASSWORD and press the key. The change the unit settings.
OPERATION VidQuad LTC 2372 & LTC 2375 Front Panel VidQuad MODE DISPLAY Menu LTC 2376 & LTC 2377 Front Panel LTC 2372 & LTC 2375 Operation 3. The VCR/DVR images can be viewed as recorded in a quad The LTC 2372 and LTC 2375 are operational as soon as power format or any quad can be zoomed to full-screen.
Page 17
6.2.5 Quad Display 6.2.7 Video Loss Alert • Press the QUAD key to display all four camera inputs on The LTC 2376 and LTC 2377 may be programmed to produce the system monitor screen. Each quadrant displays the video an alarm if the video signal to any of the four camera channels from its respective camera.
6.2.9 Computer Time/Date Interface MAINTENANCE The LTC 2376 and LTC 2377 have the capability for time and The Quad unit requires no routine maintenance and is date settings to be set from a remote device. The commands are designed for long, trouble-free use under normal as follows: operating conditions.