Motorola TalkAbout MS350MR User Manual

Body-Worn Operation
To maintain compliances with FCC/Health Canada RF exposure
®
guidelines if you wear a radio on your body when transmitting always
place the radio in a Motorola-supplied or approved clip holder, holster,
case or body harness for this product. Use of non-Motorola-approved
Two-Way Radio
accessories may exceed FCC/Health Canada RF exposure guidelines.
User's Guide
If you do not use one of the Motorola-supplied or approved body-worn
accessories and are not using the radio held in the normal use position,
ensure the radio and its antenna are at least 1 inch ( 2.5 cm) from your
body when transmitting.
Data Operation
If applicable, when using any data feature of the radio with or without an
accessory cable, position the radio and its antenna at least one inch
( 2.5 cm) from the body.
Approved Accessories
53724: Remote Speaker with Push-to-Talk Microphone
53725: Headset with Swivel Boom Microphone
53727: Earbud with Push-to-Talk Microphone
53728: Flexible Ear Receiver
56320: Earpiece with Boom Microphone
Electromagnetic Interference/Compatibility
Note: Nearly every electronic device is susceptible to electromagnetic
interference (EMI) if inadequately shielded, designed or otherwise
configured for electromagnetic compatibility. This device complies with
Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference; and
Model MS350MR
KEM ML36100 30A
2. This device must accept any interference received, including
interference that may cause undesired operation.
This radio floats with included NiMH battery.
IC Canada
It may not float with some AA batteries.
The term "IC:" before the equipment certification number only signifies
that the Industry Canada technical specifications were met.
For More Information
Facilities
For further information, you may contact Motorola Solutions, Inc. as follows:
To avoid electromagnetic interference and/or compatibility conflicts, turn
off your radio in any facility where posted notices instruct you to do so.
USA: Call 1-800-638-5119, send e-mail to giantintl@callcenter.com.
Mexico: Call 01-800-021-0000 Hospitals or health care facilities may be using equipment that is
sensitive to external RF energy.
Uruguay: Call 00-04-01-78-70-11
Panama: Call 507-340-0293
Aircraft
When instructed to do so, turn off your radio when onboard an aircraft.
This radio is not for sale in Canada.
Any use of a radio must be in accordance with applicable regulations

Safety and General Information

per airline crew instructions.
Medical Devices – Pacemakers
Important Information on Safe and Efficient Operation
The Advanced Medical Technology Association recommends that a
Read This Information Before Using Your Radio.
minimum separation of 6 inches (15 cm) be maintained between a
handheld wireless radio and a pacemaker. These recommendations are
The information provided in this document supersedes the general safety
consistent with the independent research by and recommendations of
information in user guides published prior to December 1, 2002.
the U.S. Food and Drug Administration.
Transmit and Receive Procedure
People with pacemakers should:
Your two-way radio contains a transmitter and a receiver. To control your
• ALWAYS keep the radio more than 6 inches (15 cm) from their
exposure and ensure compliance with the general population/ uncontrolled
pacemaker when the radio is turned ON.
environment exposure limits, always adhere to the following procedure:
• Not carry the radio in the breast pocket.
• Transmit no more than 50% of the time.
• Use the ear opposite the pacemaker to minimize the potential for
• To receive calls, release the PTT button.
interference.
• To transmit (talk), press the Push to Talk (PTT) button.
• Turn the radio OFF immediately if there is any reason to suspect that
Transmitting 50% of the time, or less, is important because the radio
interference is taking place.
generates measurable RF energy exposure only when transmitting (in
Medical Devices – Hearing Aids
terms of measuring standards compliance).
Some digital wireless radios may interfere with some hearing aids. In the
Exposure to Radio Frequency Energy
event of such interference, you may want to consult your hearing aid
Your Motorola two-way radio complies with the following RF energy
manufacturer to discuss alternatives.
exposure standards and guidelines:
Medical Devices – Other
• United States Federal Communications Commission, Code of Federal
If you use any other personal medical device, consult the manufacturer
Regulations; 47CFR part 2 sub-part J.
of your device to determine if it is adequately shielded from RF energy.
• American National Standards Institute (ANSI)/Institute of Electrical
Your physician may be able to assist you in obtaining this information.
and Electronic Engineers (IEEE) C95. 1-1992.
Safety and General Use While Driving
• Institute of Electrical and Electronics Engineers (IEEE) C95.
Check the laws and regulations regarding the use of radios in the area
1-1999 Edition.
where you drive, and always obey them. If you do use your radio while
• International Commission on Non-Ionizing Radiation Protection
driving, please:
(ICNIRP) 1998.
• Give full attention to driving and to the road.
• Ministry of Health (Canada) Safety Code 6. Limits of Human Exposure
• Use hands-free operation, if available.
to Radiofrequency Electromagnetic Fields in the Frequency Range
• Pull off the road and park before making or answering a call if driving
from 3 KHz to 300 GHz, 1999.
conditions so require.
• Australian Communications Authority Radiocommunications
The use of a two-way radio while engaged in activities requiring
(Electromagnetic Radiation—Human Exposure) Standard, 2003.
concentration may cause distraction or otherwise impair your ability to
• ANATEL ANNEX to Resolution No. 303 of July 2, 2002.
safely participate in such activities. Always use technology safely.
• ANATEL ANNEX to Resolution No. 533 of September 10, 2009.
Do not place a portable radio in the area over an air bag or in the air bag
To ensure optimal radio performance and make sure human exposure to
deployment area. Air bags inflate with great force. If a portable radio is
radio frequency electromagnetic energy is within the guidelines set forth
placed in the air bag deployment area and the air bag inflates, the radio
in the above standards, always adhere to the following procedures.
may be propelled with great force and cause serious injury to occupants
Portable Radio Operation and EME Exposure
of the vehicle.
Antenna Care Potentially Explosive Atmospheres
Turn off your radio prior to entering any area with a potentially explosive
Use only the supplied or an approved replacement antenna.
Unauthorized antennas, modifications, or attachments could damage the atmosphere. Only radio types that are especially qualified should be
radio and may violate FCC regulations. used in such areas as "Intrinsically Safe." Do not remove, install or
charge batteries in such areas. Sparks in a potentially explosive
Do NOT hold the antenna when the radio is "IN USE." Holding the
atmosphere can cause an explosion or fire resulting in bodily injury or
antenna affects its effective range.
even death.
Note: The areas with potentially explosive atmospheres referred to
above include fueling areas such as below decks on boats, fuel or
chemical transfer or storage facilities, areas where the air contains
chemicals or particles (such as grain, dust or metal powders) and any
other area where you would normally be advised to turn off your vehicle
engine. Areas with potentially explosive atmospheres are often—but not
always—posted.
Blasting Caps and Areas
To avoid possible interference with blasting operations, turn off your
radio when you are near electrical blasting caps, in a blasting area, or in
areas posted "Turn off two-way radios". Obey all signs and instructions.
Operational Cautions
Antennas
Do not use any portable radio that has a damaged antenna. If a
damaged antenna comes into contact with your skin, a minor burn can
result.
Batteries
All batteries can cause property damage and/or bodily injury such as burns
if a conductive material—like jewelry, keys or beaded chains— touch
exposed terminals. The conductive material may complete an electrical
circuit (short circuit) and become quite hot. Exercise care in handling any
charged battery, particularly when placing it inside a pocket, purse or other
container with metal objects.
Exercise care when removing NiMH or AA batteries. Do not use sharp or
conductive tools to remove either of these batteries.
Battery Charger Safety Instructions:
Save these Instructions
1. Do not expose the charger to rain or snow.
2. Do not operate or disassemble the charger if it has received a sharp
blow, or has been dropped or damaged in any way.
3. Never alter the AC cord or plug provided with the unit. If the plug will
not fit the outlet, have the proper outlet installed by a qualified
electrician. An improper condition can result in a risk of electric
shock.
4. To reduce the risk of damage to the cord or plug, pull the plug rather
than the cord when disconnecting the charger from the AC
receptacle.
5. To reduce the risk of electric shock, unplug the charger from the
outlet before attempting any maintenance or cleaning.
6. Use of an attachment not recommended or sold by Motorola may
result in a risk of fire, electric shock or personal injury.
7. Make sure the cord is located so it will not be stepped on, tripped
over or subjected to damage or stress.
8. An extension cord should not be used unless absolutely necessary.
Use of an improper extension cord could result in a risk of a fire
and/or electric shock. If an extension cord must be used, make sure
Date : Sept 15, 2010
that:
Model : MS350R • The pins on the plug of the extension cord are the same number,
size and shape as those on the plug of the charger.
Description : Line Arts for User Guide
• The extension cord is properly wired and in good condition.
• The extension cord size is 18 AWG for lengths up to 100 feet, and
16 AWG for lengths up to 150 feet.
9. The supply cord of the AC adaptor cannot be replaced. If the cord
is damaged, call customer service at 1-800-638-5119 in Canada or
e-mail us at giantintl@callcenter.com.

Licensing Information

Your Motorola radio has 22 operating channels. The FRS channels
operate within the range of free use frequencies and do not require

Control Buttons

authorization from your local regulatory body.
The GMRS channels may require authorization from your local regulatory
body.
Channels and Frequencies
Channel Frequency Description Channel Frequency Description
1 462.5625 MHz GMRS/FRS 12 467.6625 MHz FRS
2 462.5875 MHz GMRS/FRS 13 467.6875 MHz FRS
3 462.6125 MHz GMRS/FRS 14 467.7125 MHz FRS
4 462.6375 MHz GMRS/FRS 15 462.5500 MHz GMRS
5 462.6625 MHz GMRS/FRS 16 462.5750 MHz GMRS
6 462.6875 MHz GMRS/FRS 17 462.6000 MHz GMRS
7 462.7125 MHz GMRS/FRS 18 462.6250 MHz GMRS
8 467.5625 MHz FRS 19 462.6500 MHz GMRS
9 467.5875 MHz FRS 20 462.6750 MHz GMRS
10 467.6125 MHz FRS 21 462.7000 MHz GMRS
11 467.6375 MHz FRS 22 462.7250 MHz GMRS
Mexico
Use of GMRS frequencies is subject to the Rules and Regulations of the
Secretary of Communications and Transport (SCT) and Federal Waterproof
Telecommunications Commissions (COFETEL). SCT/COFETEL requires that
This radio is waterproof to IP-67 standards. It will withstand submersion
all operators using GMRS frequencies obtain a permit before operating
under up to 1 meter of water for up to 30 minutes. The radio is resistant
their equipment. To obtain a permit from the SCT, the user must proceed
to water, rain, and splashes only when the battery cover and headset
in accordance with Articles 14 and 15 of the Federal Telecommunications
accessory port are sealed. Open the battery compartment door or
Law. Consult your local SCT/COFETEL office for more information:
headset port cover only when the radio is dry. Use of a headset
www.sct.gob.mx./www.cft.gob.mx.
accessory should be in dry environments only.
Uruguay
The charging base and AC adaptor are not waterproof. Do not expose
Use of GMRS frequencies is subject to the Rules and Regulations of the
the charger to rain or snow. Charge the radios only in a dry location. Do
Regulatory Unit Communications Services (URSEC). URSEC requires that
not place wet radios into the charging base.
all operators using GMRS frequencies obtain a permit before operating
Installing the Batteries
their equipment. The authorization shall depend on the channel
Radio floats with included NiMH battery. It may not float with some AA
availability at the time the authorization is requested. To obtain a permit
batteries. Each radio can use either 1 NiMH rechargeable battery pack
from URSEC, consult your local URSEC office for more information:
or 3 AA alkaline batteries and beeps when the batteries are low.
www.ursec.gub.uy.
Installing NiMH Rechargeable Battery Pack ( Optional Accessory)
Panama
1. Turn the radio off.
The Republic of Panama does not require authorization to use FRS/GMRS
radio equipment frequencies. 2. With the back of the radio facing you, loosen the retaining screw on
the battery door and open the cover.
USA
Use of GMRS frequencies is subject to the Rules and Regulations of the 3. Remove the NiMH battery pack from the clear plastic bag (do not
disassemble or unwrap the battery pack).
Federal Communications Commission (FCC).
Date : Jan 14, 2011
4. Insert the NiMH battery pack with the diagram facing you. (The
The FCC requires that all operators using GMRS frequencies obtain a
ribbon should be underneath the battery pack and should wrap
radio license before operating their equipment. To obtain the FCC forms,
Model : MS350R
around the right side of the pack for easy removal.)
please visit the FCC's Web site at wireless.fcc.gov/uls/index.htm?job=home
Description : Line Arts for User Guide
to source form 605 and 159, which include all the instructions you will need. 5. Close the battery cover and tighten the retaining screw on the battery door.
If you wish to have the document faxed or mailed, or if you have Installing the Three AA Alkaline Batteries
questions, please use the following contact information:
1. Turn the radio off.
For a fax: For mail service: If you have
2. With the back of the radio facing you, loosen the retaining screw on
Contact the Call the FCC questions about
the battery door and open the cover.
Fax-0n-Demand Forms Hotline the FCC License:
3. Insert the three AA alkaline batteries with + and - polarity as shown
system Call the FCC
inside. (The ribbon should be underneath the AA alkaline batteries
and should wrap around the right side of the batteries.)
1-202-418-0177 1-800-418-FORM 1-888-CALL-FCC
4. Close the battery cover and tighten the retaining screw on the
(3676) (225-5322)
battery door.
Control Buttons
Caution: Radio may not float with some AA batteries installed.
Radio Battery Meter
The radio battery icon shows the battery charge level, from full
to empty
radio chirps periodically or after releasing
Removing the NiMH Battery Pack ( Optional Accessory)
1. Turn the radio off.
2. With the back of the radio facing you, loosen the retaining screw on
the battery door to release the battery cover and open the cover.
3. Remove the NiMH battery pack by pulling the ribbon attached to
the radio.
4. Close the battery cover and tighten the retaining screw on the
battery door.
Removing the Three AA Alkaline Batteries
1. Turn the radio off.
2. With the back of the radio facing you, loosen the retaining screw on
the battery door, release the battery cover and open the cover.
3. Gently remove each alkaline battery by easing each battery out
individually.
4. Close the battery cover and tighten the retaining screw on the
battery door.
Notes
• Exercise care when removing NiMH or AA batteries. Do not use
sharp or conductive tools to remove either of these batteries.

Display Screen Guide

Display Screen Guide
• Remove the batteries before storing your radio for extended periods
of time. Batteries corrode over time and may cause permanent
damage to your radio.
• The battery door must be tightly closed with the screw to maintain
the waterproof seal of the radio.
Using the Battery Charger ( Optional Accessory)
The battery charger provides drop-in charging convenience for NiMH
batteries and can be placed on any flat surface, such as a desk or
workbench. Charge the NiMH battery overnight (at least 16 hours) before
using it for the first time. After the initial charge, an empty battery is fully
charged within 14 hours.
1. Follow the steps above to install a NiMH Battery Pack.
2. Plug the AC power supply cord into the jack on the desk stand.
3. Plug the AC power supply into a standard wall outlet.
4. With a radio facing forward, slide it into one of the charging pockets.
5. When charging in the battery charger, the red light on the charger
base will glow continuously.
Notes
• The light will remain red after the NiMH battery pack is fully charged.
• When moving between hot and cold temperatures, do not charge the
NiMH battery pack until the battery temperature acclimates (usually
about 20 minutes).
• For optimal battery life, remove the radio from the charger within 16
hours. Do not store the radio while connected to the charger.
• If the radio is kept on while charging, the charging time will be extended.
• Even though the charger is connected, you may not be able to transmit
Getting Started
a message if the battery is completely empty
battery to charge to 1 bar
• When the radio is wet from rain or snow, thoroughly dry the surface
Control Buttons
before charging or removing the batteries.
Attaching and Removing the Belt Clip
1. Attach belt clip to pocket or belt strap.
2. Align the belt clip post with the hole in the back of the radio.
3. Gently push until the clip clicks in place.
To Remove
1. Push down on the release tab at the top of the belt clip to release
the catch.
2. Pull the belt clip away from the back of the radio.
Turning your Radio On and Off
In the ON position, the radio chirps and briefly shows all feature icons
available on the radio. The display screen then shows the current
channel, code and all features that are enabled.
Press and hold for 3 seconds to turn the radio on. Press and hold
for 3 seconds to turn the radio off.
Setting the Volume
Press and hold for three seconds, then press the
you reach a comfortable listening level.
The MS350MR Series has 16 volume levels controlled by the
keys.
1. Press to increase volume.
2. Press to decrease volume.
3. Hold or to rapidly increase volume.
Do not hold the radio close to your ear. If the volume is set to an
uncomfortable level, it could hurt your ear.
Talking and Listening
To communicate, all radios in your group must be set to the same
channel and Interference Eliminator Code.
1. To talk, press and hold
2. When you are finished talking, release
For maximum clarity, hold the radio two to three inches away from your
. When the radio has one segment left, the radio chirps
mouth and speak directly into the microphone. Do not cover the
(Low Battery Alert).
microphone while talking.
Talk Range
Your radio is designed to maximize performance and improve
transmission range. Do not use the radios closer than five feet apart.
Power Boost
To boost your radio's power up to high power, press the top portion of the
button when talking. If you know your party is close by, you can
conserve your battery's energy by pushing the lower part of the
button to use less power.
Note: If you are on an FRS only channel (see Channels and Frequencies
table) the radio will only use low power when either portion of the
is pressed.
Monitor Button
Use the Monitor function to check if a channel is currently in use by
others. For maximum range performance, the Monitor function will also
help you to hear signals that are weak.
To latch the Monitor function on, press and hold
When an empty channel is located, you will hear continuous static and
noise on that channel.
To turn the Monitor function off, tap
Push to Talk Timeout Timer
To prevent accidental transmissions and save battery life, the radio emits
a continuous warning tone and stops transmitting if you press
continuous seconds.
There are 10 options you may set to your preferences. Each press of the
MENU key advances you to the next option setting. Press the
keys to change the setting. The menu will automatically close 5 seconds
after the last press of any button. After the last menu item, the radio exits
MENU mode and returns to operation of the radio. A press of the button
while setting any menu option will immediately save all your settings and
return to operation of the radio.
All MENU settings will revert back to the factory default values if the
battery is fully discharged or removed for more than 30 seconds.
Menus and Values
1. Channel (1-22)
2. Interference Eliminator Code (1-121 or OFF)
3. Call Tone (1-10 or OFF)
4. iVOX (ON/OFF)
5. VOX sensitivity (1-3)
6. QT Noise Filtering (ON/OFF)
. Allow time for the
before attempting to transmit a message.
Control Buttons
or keys until
or
.
.
for three seconds.
a second time or press .
for 60
Menu Options
or
Continued on back
Model MS350MR